revelo LIFT 20 Bike Owner’s Manual
- June 5, 2024
- revelo
Table of Contents
revelo LIFT 20 Bike
visit www.revelo.ca/pages/manuals for the latest updates
Safety – Read This First!
- Always make sure the stem, handlebar, seat and wheels are fully tightened by making sure the quick release levers are firmly closed.
- Make sure the quick release lever for the folding hinge is securely closed. Refer to the section on Folding.
- Do not attach a front bicycle basket to the handlebars or dangle any bags/objects from the handlebar/stem system unless they are designed to specifically work with your LIFT
- Do not ride on surfaces where the wheels or pedals could get caught (e.g. on train/ tram tracks, or potholes) and do not ride directly into bumps or curbs.
- Do not attempt any stunt riding (eg. jumps, sharp turns, wheelies).
- When adjusting the height of your saddle, if the “Minimum Insertion” marking is visible on the vertical post then insert the post deeper into the fra
- Wear a regionally certified, properly fitted bicycle helmet.
- The total weight of the rider and backpack must not exceed 100 kgs (220 lbs).
- If your model came equipped with handlebar ends, check that the grips are tightly secured to the handlebar.
- Tires should not be inflated past the recommended pressure that is marked on the sidewall.
- For night riding, inspect that your bike reflectors are not missing or damaged. Always have your front and rear lights on and wear reflective gear.
- Obey all local and national traffic, helmet laws and never ride while under the influence of drugs or alcohol.
- Before your first ride, practise riding in a safe open area with a smooth surface that is away from other pedestrians and vehicles (eg. a vacant parking lot)
Assembly
This guide provides the basic information to get you going quickly before you
ride. If you are unsure of any aspect of LIFT, please bring your LIFT to a
professional bicycle mechanic for final assembly.
Visit www.revelo.ca for additional information.
Some illustrations may not be exactly as shown.
Tools You Need
- Pedal wrench (models equipped with folding pedals require a 15mm wrench.
- 4mm allen key to adjust the stem collar. (3) 5mm allen key to adjust the handlebar clamp and magnet plate. (4) Pump to inflate tires.
Step 1: Attach Handlebar
If the handlebar is already attached, go to Step 2:
Setting Up The Stem.
If necessary, temporarily remove the stem collar ① from the handlebar post by
loosening the pinch bolt with an allen key.
Insert vertical handlebar post ② down into the stem ③Loosen the handlebar post
clamp m to center the handlebar and rotate the handlebar so the brake levers ⑤
are facing towards the front of the bike. Tighten the handlebar clamp ④ once
the handlebar is properly positioned.
Step 2: Setting Up The Stem
The Stem Collar ① allows for quick centering of the handlebar and resists
twisting by locking into the stem ②. Carefully follow all instructions to
avoid handlebar twisting during riding and potential injury
NOTE: The stem collar for 2021 and newer is silver. Some illustrations may
show a black stem collar but the install is identical.
2a: Remove Stem Collar
Using an allen key, loosen the pinch bolt ③ on the stem collar and temporarily
remove the collar ① from the handlebar post ④.
2b: Set Handlebar Position for Riding
Open quick release levers ⑤. Slide the handlebar to the desired riding height
and turn it until it is perpendicular to the front wheel. Firmly close both
quick release levers ⑤ .
If necessary, rotate the adjustment knob ⑥ clockwise to increase clamping
strength and counter-clockwise to loosen.
Test clamping pressure by placing the front wheel between your feet and
attempt to twist the handlebar. If handlebar twists, more clamping pressure is
required. ( Use the adjustment knob to increase clamping pressure ).
Optimal clamping pressure typically leaves a small impression on the palm of
your hand or thumb.
2c: Identify Stem Collar Tooth & Notch
The stem collar tooth ⑦ is designed to mate into a notch ⑧ in the stem (ensure
there is no gap).
2d: Install Stem Collar
Slide the stem collar ① back onto the handlebar post ④ with the notched tooth
⑦ facing towards the bike.
2e: Bolt Stem Collar
Mate the stem collar tooth ⑦ into the stem notch ⑧(do not leave gap).
Tighten pinch bolt ③ with allen key.
2f: Close Levers Before Riding
Ensure that both quick release levers ⑤ are firmly closed prior to riding.
The handlebar can always be lowered for thin profile walking or folding as needed (refer to the Folding and Carrying & Rolling sections). For instant height adjustment before riding, slide the handlebar up until the stem collar locks into the stem. Then, firmly close both levers.
Before every ride ensure the stem collar is fully mated and quick releases are firmly closed so that the handlebar can not twist !
Step 3: Attach Pedals
( For models with Detachable Pedals, skip this section and refer to the user manual included with the pedals for installation ).
Folding Pedal installation requires a 15mm wrench.
Pedals tighten opposite to each other. Left (L) pedal tightens counter-
clockwise. Right (R) pedal tightens clockwise.
Left Pedal: Insert pedal axle into crank arm threads and turn axle
counter-clockwise. Start by using fingers first then tighten with a 15mm
wrench.
Right Pedal: Insert pedal by turning axle clockwise.
Push pedal inwards towards frame to release locking pegs ①, then rotate to
fold ②. Reverse procedure to unfold pedals.
Step 4: Attach Seat
Ensure seat post is inserted so that the minimum insertion line is not visible above the clamp.
Open seat post lever ① and insert seat post ② into frame ③.
Tighten seat post clamp so that the lever is folded over and closed.
If necessary, rotate the adjustment knob m clockwise to increase clamping
strength and counter-clockwise to loosen.
Step 5: Tighten Magnet Plate
Using a 5mm allen key, tighten the magnet plate so that the plate is
perpendicular to the ground. Test and adjust if needed by folding the bike
following the “Z-fold” instructions in the next section. The whole magnet
should contact the plate for maximum holding strength when the bike is folded
and rolled.
Using Your LIFT
Bike Fit
LIFT is incredibly lightweight and built for spontaneous living. Go everywhere you desire at any given moment.
The LIFT’s design allows for a fully adjustable bike rider fit from 147-186cm (4’10”-6’2″) & up to 100 kgs (220lbs).
Revelo’s patented THINstem rotating handlebar system provides instant rider height adjustment and a thin walking profile.
Folding
LIFT is one of the fastest folding, easiest rolling and most portable performance folding bikes on the market!
During the “break-in” period, the frame hinge may exhibit some stiffness. This will improve quickly with regular use.
1: Open Fork Mounted Kickstand
Open the fork mounted kickstand ① to the folding position.
2: Adjust Right Pedal Position
Set your right pedal ② to the 7 o’clock position. This prevents pedals from
tangling with brake cables during folding.
Folding the pedals (or removing them if equipped with detachable pedals) helps
with the folding procedure.
3: Lower & Rotate Handlebar
Release both stem quick release levers then drop the handlebar down ③ towards
the front tire. Pivot the handlebar 90° clockwise ④ then lock into place with
levers ⑤.
Do not pinch or over-twist cabling.
4: Lower Seat
Lower the seat as much as possible .
Tighten seat post clamp ⑥.
5: Unlock & Open Frame Lever
The frame is locked in place with a hinge clamp and lever. To unlock, first
position yourself to the left side of the bike. Place your right palm over the
lever then press the lever against the frame while sliding the button ⑦ at the
top of the lever towards the front of the bike; simultaneously grab the lever
from below and pull the lever out away from the bike
When securely relocking the hinge, ensure that the ball head screw ⑧ behind
the lever is not visible.
The hinge clamp is factory set for optimal clamping. Over time, if opening/closing the lever becomes difficult or loose, adjust the ball head screw ⑧ behind the lever.
Rotating the screw clockwise will create a looser hinge and counter-clockwise to tighten the hinge. Optimal clamping is one that provides a moderate “snap”
8: Fold the Frame
With the frame lever open and handlebar locked in a 90° position:
Using your left hand, grab the handlebar ⑨.
Using your right hand, grab the built-in frame handle ⑩ and lift the rear.
Pivot the frame in a “Z” fashion ⑪ to draw the rear wheel towards the front
wheel until the magnets lock ⑫.
9: Close Frame Lever
Flip the frame lever ⑬ inwards for a compact, tidy look.
To disengage the frame magnets ⑫ for unfolding, while holding the frame it is
sometimes helpful to give the rear tire a slight kick.
Carrying & Rolling
LIFT keeps you moving even after the ride:
Use the built-in frame handle for easy, convenient transport.
With the crank facing outward, loop one end over the seat and the other over the forward most handle grip
With LIFT unfolded, pivot & lock the handlebar at 90° to create a thin walking profile.
Standing left of LIFT, grab the handlebar. Tilt LIFT slightly back on its rear
wheel, then roll as you walk. Optional: Extend & lock the seat, hold it and
roll.
Gears
Your multi-speed LIFT has a derailleur drive train. Low gears (down to 1) require less pedalling effort and are ideal for steep hills. For flatter terrain and faster speed, shift to a higher gear (higher number).
Only shift gears while the bike/rear wheel is moving forward and the chain is under tension.
Wheels
If your model is equipped with a Quick Release wheelset, you may want to remove it occasionally for eg. travel, storage or service.
Front Wheel
- Disengage the brake quick-release mechanism to move the brakes away from the rim.
- Open the quick-release wheel lever by pulling away from the wheel.
- While holding the fork with one hand, pull the wheel out from the fork dropouts.
Rear Wheel
- Set the gear to its highest position. This moves the chain and derailleur to the outermost position.
- Disengage the brake quick-release mechanism to move the brakes away from the rim.
- Open the quick-release wheel lever by pulling away from the wheel.
- While standing behind the bike, use your right hand to pull backward on the derailleur body.
- Use your other hand and pull the wheel out from the fork dropouts.
Maintenance
LIFT has a warranty of 5 years on the frame and fork, and 1 year on non-wear
items including quick releases and frame hinge lever. In addition to regular
bike maintenance and annual tune up, it is important to also maintain
(1) stem quick releases, and (2) the hinge locking system. Please refer to the
videos in the tutorial section online:
“Maintaining the THINstem Quick Release” and “Operating the Revelo LIFT
Frame Hinge”. Most routine service below can be performed by the owner.
Consult your local bicycle repair shop as required.
Clean the frame of dirt and debris as needed using a soft, damp cloth, warm water and non-detergent based soap. Do not use power washers. Relubricate the chain with a chain lubricant only.
Periodically check to ensure that fastening bolts have not loosened. Hand tighten with the appropriate tool as necessary. Do NOT use power tools to tighten any bolts.
Check brake pad wear. Adjust if they do not properly hit the wheel rim.
Periodically check tire pressure as indicated on the sidewall.
Check for missing spokes and for non-trued (wobbly) wheels.
Check headset stiffness. While squeezing the front brake, rock the bike back and forth. Clunking noises could indicate a loose headset.
Check frame for any noticeable signs of fraying or cracks.
Thank you for choosing Revelo LIFT. Enjoy your ride!
#RideRevelo
If you are unsure of any aspect of LIFT, please bring your LIFT to a
professional bicycle mechanic.
www.revelo.ca
References
- Revelo | Premium Folding Bike Technology. Exclusive Anti-lock Braking
- Portable Bikes Owner's Manual - Revelo Bikes