decon wheel MEM6137P Remover and Wheel Cleaner Instruction Manual
- June 12, 2024
- decon wheel
Table of Contents
decon wheel MEM6137P Remover and Wheel Cleaner
Product Information
The product in question is the Helium and Nitrum, specifically the MEM6137P and MEM6138P models.
Assembly Instructions for Helium and Nitrum
- Remove wheels and sleeves. This applies only to the STD rear axle and not the PRO rear axle or short COG rear axle.
- Assemble the plate (right side) according to the provided picture. The following parts are required for right side mounting:
Item No.| Part Number| Qty| Description
---|---|---|---
1| HW072| 1| Hub sleeve
2| XSTM6X12| 1| Stop Screw M6 x 12
3| XSM8X16| 1| Screw: Round – M8 x 16
4| 310031| 1| Bracket
5| 320003| 1| Stop Pin
Note: If you only order the mounting set, the axle is not included. Please refer to the service manual for replacement options.
- Assemble the under placed battery bag or, if you have ordered a Lithium battery, place the battery holder as shown in the provided picture.
Assembly of Battery Bracket MEM5015
Item No. | Part Number | Qty | Description |
---|---|---|---|
1 | MEM5002 | 1 | Hoop Clamp |
2 | MEM5003 | 4 | Screw Countersunk M5 x12 |
3 | XSFM5X12 | 2 | Nut Self-Locking M5 Bolt |
4 | XSM5ML | 2 | Round-Square M8 x16 Nut Self-Locking M8 |
5 | XSSM8X16 | 4 | Battery plate eDrive/ eMove Screw Countersunk M6 x16 Nut |
Self-Locking M6
6| XSM8ML| 4| Bracket
7| MED5001 Rev3| 1| –
8| XSFM6X16| 4| Screw Countersunk M6 x16
9| XSM6ML| 4| Nut Self-Locking M6
10| MEM5011| 1| Bracket
Product Usage Instructions
To assemble the Helium and Nitrum, follow these steps:
- Start by removing the wheels and sleeves. This step is necessary only if you have the STD rear axle.
- Next, assemble the plate on the right side according to the provided picture. Use the following parts: Hub sleeve (HW072), Stop Screw M6 x 12 (XSTM6X12), Screw: Round – M8 x 16 (XSM8X16), Bracket (310031), and Stop Pin (320003).
- If you have ordered a Lithium battery, place the battery holder as shown in the picture. If not, assemble the under placed battery bag.
- For the assembly of the battery bracket (MEM5015), follow the provided instructions and use the specified parts.
Note: If you have only ordered the mounting set, please note that the axle is not included. Refer to the service manual for replacement options.
Assembly instructions for Helium and Nitrum With 0° Camber MEM6137P and MEM6138P
-
Remove wheels and sleeves.
Only STD rear axle. Not PRO rear axle or short COG rear axle. -
Check the correct placement for the eMove and assemble with axle Ø12,7-46 with part number: X0E-2530E-00. Stop pins are assembled with Part Numbers: 320003.
-
Assemble the plate (right side) according to picture.
Parts for right side mounting:
Item | No. | Part Number | Qty | Description |
---|---|---|---|---|
1 | HW072 | 1 | Hub sleeve | |
2 | XSTM6X12 | 1 | Stop Screw M6 x 12 | |
3 | XSM8X16 | 1 | Screw : Round – M8 | x 16 |
4 | 310031 | 1 | Bracket | |
5 | 320003 | 1 | Stop Pin |
Note! If you only order the mounting set, the axle it’s not included, for replacement see the service manual.
- Assemble the under placed battery bag or if have order a Lithium battery place the battery holder as the picture bellow.
Assembly of Battery bracket MEM5015
Item | No. | Part Number | Qty | Description |
---|---|---|---|---|
1 | MEM5002 | 1 | Hoop | |
2 | MEM5003 | 4 | Clamp | |
3 | XSFM5X12 | 2 | Screw Countersunk M5 x12 | |
4 | XSM5ML | 2 | Nut Self-Locking M5 | |
5 | XSSM8X16 | 4 | Bolt Round-Square M8 x16 | |
6 | XSM8ML | 4 | Nut Self-Locking M8 | |
7 | MED5001 Rev3 | 1 | Battery plate eDrive/ eMove | |
8 | XSFM6X16 | 4 | Screw Countersunk M6 x16 | |
9 | XSM6ML | 4 | Nut Self-Locking M6 | |
10 | MEM5011 | 1 | Bracket |
Tightening torque
Metric coarse threads, steel.
Thread | Tightening torque |
---|---|
M3 | 1,2 Nm |
M4 | 3 Nm |
M5 | 6 Nm |
M6 | 10 Nm |
M8 | 25 Nm |
M10 | 50 Nm |
M12 | 85 Nm |
Hubsleever.
Thread | Tightening torque |
---|---|
M16x1 | 30 Nm |
M18x1 | 40 Nm |