Panasonic ER-CTW1 Multifunctional Trimmer Instruction Manual

: June 12, 2024
: Panasonic

Table of Contents

Panasonic ER-CTW1 Multifunctional Trimmer
Troubleshooting
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Panasonic ER-CTW1 Multifunctional Trimmer

Product Information

Model No.: ER-CTW1
Language: English

Important Information

A: head
B: Water inlet
C: Trimming height indication mark
D: Dial (Height adjustment control)
E: water outlet
F: blade
G: Comb attachment [A] (1 mm to 10 mm)
H: Comb attachment [B] (11 mm to 20 mm)
I: Comb attachment [C] (21 mm to 30 mm)
J: Comb attachment for body hair [D]

Product Usage Instructions
Mounting the Head

Hold the head and align it with the main body.
Push the head onto the main body until it clicks into place.

Mounting the Comb Attachment

Select the desired comb attachment (G, H, or I) based on the desired trimming height.
Align the comb attachment with the head and push it onto the head until it clicks into place.

Note: The trimmer can also be used without the comb attachment for a trimming height of approximately 0.5 mm.

Turning on the Power
Switch on the power to start using the trimmer.

Removing and Mounting the Head

To remove the head, push the head release button and lift the head off the main body.
When the head is removed, stand it upright.
To mount the head, align it with the main body and push it down until it clicks into place.

Cleaning the Trimmer
Removing Light Dirt

Remove the comb attachment.
Run water down the water inlet to remove light dirt.
Shake the head up and down several times to remove excess water.
Wipe off any remaining water with a dry cloth and ensure it is completely dry.

Removing Heavy Dirt

Remove the head, comb attachment, and blade.
Rinse them with running water to remove heavy dirt.
Shake the head up and down several times to remove excess water.
Wipe off any remaining water with a dry cloth and ensure all parts are completely dry.

Removing and Mounting the Blade
To remove the blade

Hold the head securely.
Place your thumb against the blades and push them away from the head.

To mount the blade

Fit the mounting hook into the blade mounting on the head.
Push in until you hear a click to secure the blade.

Lubrication

Apply a drop of lubrication oil to each indicated point.
Attach the blade to the head.
Switch on the power and allow the trimmer to run for approximately 5 seconds.

Troubleshooting
If the trimmer becomes blunt or makes a loud sound:

Clean the blade and apply lubrication oil.
If the problem persists, replace the blade.
If the problems still cannot be solved, contact your dealer or a service center authorized by Panasonic for repair.

Specifications

Airborne Acoustical Noise: 66 dB (A) re 1 pW
This product is intended for household use only.

Before operating this unit, please read these instructions completely and save them for future use.

Please read the code on the cover for detailed operating instructions.

Important information

Apply the lubrication oil to the blade before and after each use.
Failure to apply the lubrication oil may cause the following problems.
The appliance has become blunt.

Parts identification
(Fig. 1) A Head

Panasonic-ER-CTW1-Multifunctional-Trimmer-FIG-1

Water inlet
Trimming height indication mark
Dial (Height adjustment control)
Water outlet
Blade

B Comb attachment [A]

(1 mm to 10 mm)
C Comb attachment [B]
(11 mm to 20 mm)
D Comb attachment [C]
(21 mm to 30 mm)
E Comb attachment for body hair [D]

How to use

Clean the appliance after use.
Mount the head to the main body until it clicks.
Mount the desired comb attachment and adjust the trimming height as needed.
It can also be used without the comb attachment.
(Trimming height: approx. 0.5 mm)
Turn on the power

Note
The use time after a full charge is as follows.

ER-CBL1: 70 minutes
ER-CBN1: 40 minutes

(Based on dry use at 20 °C – 30 °C)
The operating time may differ depending on the frequency of use and the operating method.

Removing and mounting
(Fig. 2)

Remove the head while pushing the head release button (C ).
Stand the head when it is removed.
Mount the head to the main body until it clicks.

Removing and mounting
the comb attachment (Fig. 3) Remove the comb attachment from the head. Mount the comb attachment to the head until it clicks.

How to clean

Make sure that the main body is turned off.
Lubricate after cleaning

To remove light dirt To remove heavy dirt

Remove the comb attachment, and run water down the water inlet. (Fig. 4)
Remove the head, comb attachment, and blade, and rinse them with running water.
Shake up and down several times to remove the water.
Wipe off the water with a dry cloth and dry it well.
Removing and mounting the blade
To remove the blade, hold the head, place your thumb against the blades, and then push them away from the head. (Fig. 5-1)
To mount the blade, fit the mounting hook ( C) into the blade mounting on the head ( B) and then push in until you hear a click. (Fig. 5-2)

Replacement parts