AlgoLaser DELTA Laser Engraver User Guide

AlgoLaser DELTA Laser Engraver

Before You Start

Disclaimer and safety Guidelines

1. The laser engraver emits laser light. Placing any living body under the laser emission port (marked with an orange warning sign) is strictly forbidden.
2. Patients with photosensitive epilepsy are prohibited from using or approaching the laser engraver.
3. When using the laser engraver, the operator and anyone near the machine must wear laser safety goggles. Operating the laser engraver without goggles’ protection is not allowed. Our machine comes with a pair of safety goggles, but additional laser safety goggles need to be purchased separately. The goggles should offer wavelength protection of 400-445m (±Sm), an outer diameter of +5, and a minimum L-level LS.
4. Avoid placing flammable materials near the laser engraver. When the laser engraver is running, closely observe it and avoid leaving it unattended to prevent the engraved objects from catching fire. Set up the laser engraver in a fireproof area and ensure proper ventilation. If possible, we recommend purchasing a fire extinguisher and keeping it nearby the machine.
5. Ensure there is enough space when operating the laser engraver. Engraving certain materials may produce smoke, so it’s important to use exhaust equipment to vent the smoke out.
6. When the machine is running, avoid letting your body or other objects touch the laser beam, as this may cause serious bodily injury or beam reflection. Do not touch the radiator, as it may still be hot even after the laser engraver has stopped working.
7. Do not allow children or teenagers to use the laser engraver alone, especially children under the age of 14. Adult supervision is required at all times.
8. The operating temperature range of the machine is -10° C to 40° C.
9. The use of the laser engraver carries a significant risk of fire.
   When operating the machine, please ensure that someone is available to handle any potential fire emergencies at all times.

Parts List

Machine

• A. Front Assembly * 1
• B. Left Y-Axis Assembly * 1
• C. Right Y-Axis Assembly * 1
• D. Rear Panel Assembly * 1
• E. X-Axis Assembly * 1
• F. ILB-20A Laser Module *1

Laser module

Consumable

MACHINE ASSEMBLY

Remove the Packaging

Step 1: Hold the handle and remove the foam from the packaging box.
Please note that the machine and foam should be taken out together and must not be separated.

Assemble the X-Axis Assembly

Step 2: Take out the small sponge and its accessories from the foam.

Take out the Laser Module

Mount the Air Assist

Mount the Laser Module

Step 5: Take out X-Axis Assembly, and mount the Laser Module on it.

Mount the Laser Module

Step 6: Insert the laser module into the fixture from the top and raise the lever, ensuring it makes contact with the magnet for a secure fit.

Assemble the X-Axis Assembly

Step 7: Place X-Axis Assembly on the top of the machine.
NOTE: X-Axis Assembly with the end of the Cable Box should face Left Y-Axis Assembly.
Then install the end with Cable Box of X-Axis Assembly on the Block of Left Y-Axis Assembly with 2 screws. Install the other end of the X-Axis Assembly on the Block of Right Y-Axis Assembly with 2 screws.

Screw type: M4X10 Screw

Take Out the Machine

Tighten the Belt

Step 9: Install a screw on E (X-Axis Assembly), and tighten the screw until the belt is properly tightened (this means the laser module can move smoothly}.

Screw type: M4X22 Screw

Adjust the Belt

Step 10: Slide the X-Axis Assembly and ensure smooth movement. If it doesn’t slide smoothly, please adjust the screw. Turning the screw in the “+” direction tightens the belt, while turning it in the “-” direction loosens the belt.

Flip the Machine

Step 11: Turn the machine upside down and attach the Feet and Antennae to the bottom.
Then flip the machine back over, placing it face-up.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>