Commerical Electric 1005730702 2 Bar LED Under Cabinet Light User Guide
- June 4, 2024
- Commerical Electric
Table of Contents
1005730702 2 Bar LED Under Cabinet Light
User Guide
THANK YOU
We appreciate the trust and confidence you have placed in Commercial Electric
through the purchase of this under cabinet light We strive to continually
create quality products
designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing
Commercial Electric!
Product Description
SPECIFICATIONS
11W(2PK)
Input: 120V/60Hz
Safety Information
Carefully read and understand the information in this manual before you begin the installation. Failure to do so could lead to electric shock or a fatal hazard.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING: This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC Rules and
ICES-005 of the IC Rules. These limits are designed to provide reasonable
installation protection. This equipment generates and can radiate radio
frequency energy and, ii not installed and used in accordance with the
instructions may cause harmful interference.
However, there is no guarantee that interference will not occur in a
particular installation. II this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving area.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to a different outlet and circuit from the receiver outlet and circuit.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: This is a non-replaceable LED light source.
Do not dismantle this fixture. There are no user-serviceable parts inside.
CAUTION: For indoor and dry location use only.
CAUTION: Do not touch the fixture when the light source is ON.
CAUTION: Deviation from the assembly instruction may result in a risk of
fire and electric shock.
CAUTION: Do not operate this fixture with a missing or damaged cover or
housing.
CAUTION: Do not mount this fixture near a heat source as it may damage
this fixture.
CAUTION: Do not stare directly into the LED light.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons:
a) Use only insulated staples or plastic ties to secure cords;
b) Route and secure cords so that they will not be pinched or damaged when the
cabinet is pushed to the wall;
c) Position the portable cabinet light with respect to the cabinet so the lamp
replacement markings are able to be read during rel amping;
d) Not intended for recessed installation in ceilings, or soffits;
e) The National Electrical Code (NEC) does not permit cords to be concealed
where damage to insulation may go unnoticed. To prevent fire danger, do not
run cords behind walls, ceilings, soffits, or cabinets where it may be
inaccessible for examination.
Cords should be visually examined periodically and immediately replaced when
any damage is noted.
Limited Warranty
The manufacturer warrants this product to be free from defects in materials
and workmanship for a period of three (3) years from the date of purchase.
This warranty applies only to the original consumer purchaser and only to
products used in normal use and service. II this product is found to be
defective, the manufacturer’s only obligation, and your exclusive remedy, is
the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty
shall not apply to any product that is found to have been improperly
installed, set up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the
product as a result of an accident, misuse, abuse, negligence, alteration,
faulty installation, or any other failure not relating to faulty material
workmanship. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including
labor/expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at
1-877-527-0313 or visit
www.HomeDepot.com.
Pre-Installation
PLANNING INSTALLATION
Compare all parts with the parts listed in the Package Contents section. If
any part appears missing or damaged, do not install and use this light.
Contact customer service.
TOOLS REQUIRED
Package Contents
NOTE: Hardware not shown to actual size.
Part | Description | Quantity |
---|---|---|
A | LED bar light | 2 |
B | Direct connector | 1 |
C | Rotatable clip | 4 |
D | Double-sided tape | 4 |
E | Self-tapping mounting screw | 4 |
F | Linking cord 450 mm ( 17 in.) | 1 |
G | Wire Guides | 8 |
H | Linking cord 1020 mm (40 in.) | 1 |
I | AC/DC Adaptor 24V / 2.0A /1.82 m (6 ft.) cord | 1 |
Installation
PLANNING INSTALLATION
Before installation, make sure the surface you intend to mount the product on
is free of moisture, oil, grease, dust, and dirt to ensure proper adhesion.
Test painted surfaces. Adhesive tape may damage the surface when removed.
Option 1.
Remove both of the screw hole covers.
Place the light over the desired mounting location and mark the center of the
holes to be tapped.
Secure the light to the surface with the two sell-tapping screws (E).
Place the screw hole covers back.
Option 2.
Take out the rotatable clip (C) and open as shown in the figure.
Place the clip (C) over the desired mounting location and mark the center of
the holes to be drilled. The hole centers of the two clips must be in a
straight line.
Secure the clips (C) to the surface with the sell-tapping screws (E).
Place the lights in the clips (C) as shown in the figure.
Adjust the clips (C) to the desired angle.
Choose the clip direction accordingly, which decides the bar light rotating
direction.
Option 3.
Take out the clip (C) and attach the double-sided tape (D) onto the clip (C)
as shown in the figure.
Place the clip (C) in the desired locations.
Place the lights in clip (C) as shown in the figure.
Adjust the clip (C) to the desired angle.
Choose the clip direction accordingly, which decides the bar light rotating
direction.
Affix self-adhesive wire guides (G) to desired locations as needed to guide and secure the linking cord and AC/DC plug-in adaptor cord.
Movement sensor
NOTE: Wave your hand once below the sensor to turn ON the light, and wave
again to turn it OFF.
After the light is turned ON, hold your hand under the sensor for a few
seconds to activate the dimming function. The brightness will repeat from
highest to lowest and then from lowest to highest. Move your hand away from
the sensor range at your desired brightness, which will be memorized by the
light even if alter power is cut off.
6 To link more lights
Attention: The LED units on the same series can be powered by one
adaptor, the maximum linkages are 9 units.
Only connect to the lights of the same series. (UCL006IS2-UL)
Only ONE light is allowed to receive the main power input from the supply
circuit.
Otherwise, it will cause damage or lire.
Link the light with the direct connector (B).
Link the light with the 17 in. cord (F).
Link the light with the 40 in. cord (H).
Questions, problems, missing parts? Before returning to the store, call
Commercial Electric Customer Service
8a.m.-7p.m., EST, Monday- Friday, 9a.m.- 6p.m. Saturday.
1-877-527-0313
HOMEDEPOT.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>