saxby 49909 Outdoor Wall Light Instruction Manual

: June 12, 2024
: saxby

Table of Contents

saxby 49909 Outdoor Wall Light
Product Usage Instructions

saxby 49909 Outdoor Wall Light

Equinox Outdoor Wall Light (49909)

INSTRUCTION MANUAL

Safety Warnings
This is a Class 1 product and must be earthed.

Care Information
Do not clean the units with a pressure washer.

Assembly/ User Instructions

Before you start

The Light pack contains:

Equinox Outdoor Wall Light (49909)

The following tools may be required:

Not specified

UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

Assembly/ User Instructions Continued

Layout
Installation position of each set of wires.

Wiring
Carefully note the A, B, C, D markings on the wires.

A – Not specified
B – Not specified
C – Not specified
D – Not specified

Gasket Drain Hole
Ensure the gasket drain hole is not blocked.

Front view of mounting box
Check that the front view of the mounting box aligns with the desired installation position.

Commissioning
V4 18/04/2022
For more information, visit www.saxbylighting.com

Product Usage Instructions

Ensure the product is properly earthed before installation.
Do not use a pressure washer to clean the units as it may damage the product.
Before starting the assembly, check the contents of the light pack and ensure you have all the necessary tools.
Follow the layout instructions to determine the installation position of each set of wires.
When wiring, carefully note the markings (A, B, C, D) on the wires.
Make sure the gasket drain hole is not blocked to prevent water accumulation.
Align the front view of the mounting box with the desired installation position.
Once installed, commission the product according to the provided instructions.

For additional information and support, please visit www.saxbylighting.com.

Equinox Outdoor Wall Light (49909)
INSTRUCTION MANUAL

Safety Warnings

This is a Class 1 product and must be earthed.

Please read these instructions carefully before commencing any work, and retain for reference.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully and responsibly. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
This product is rated at IP44.

The shade must be replaced immediately should it become cracked or damaged. This fitting must not be used without the shade in place.

Care Information

Do not use solvents or abrasive cleaners as these could damage the finish. Do not clean the units with a pressure washer.
In normal circumstances, stainless steel is very resistant to corrosion, but may require maintenance to preserve the high quality appearance. Wash the product with warm soapy water, removing all surface deposits. Rinse with clear water, and with a soft cloth, wipe dry.
In some cases, surface corrosion may arise after installation. This is normally caused by tiny iron particles left behind after the brushing process when finishing. Wash and dry as detailed above, then with a soft cloth soaked with a protective oil, wipe all over.
If the product is subject to extreme environmental conditions such as marine locations, industrial pollution, or acid rain, these maintenance procedures should be carried out around four times a year. For severe corrosion, non- abrasive cream cleaners or proprietary stainless steel cleaners should be used to remove the corrosion. Wash, dry and coat with oil, as detailed above.
Glass parts – Remove and wash in warm water or just use a damp cloth. Do not use abrasive materials as these will damage the finish.

Assembly/ User Instructions

Before vou start

Check the packaging and make sure that you have all the required parts. Follow each assembly step in order to prevent incorrect assembly. Ensure that the product is fully assembled as illustrated before use.

The Light pack contains:

Light fitting.
Terminal connection block(s).
Fixing pack.

The following tools may be required:

Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Layout

Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box and the light fitting
Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged
Cables in walls must be protected using suitable conduit or plastic trunking.
The mains supply cable must have a minimum cross sectional area of 1.0mm?
This product has special protection against the ingress of moisture and is IP44 rated.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

saxby-49909-Outdoor-Wall-Light-2

Remove mounting box (A) from product by removing dome nuts (C) and washers (D). Pull terminal block off of retaining pegs. Carefully pierce a small hole in the rubber gasket in the centre of the mounting box to allow the cable to pass through.
Thread the cable through the hole, ensuring the drain hole is at the base of the mounting box.
Fix the mounting box to the wall using the screws and plugs supplied (B). Ensure the wall is capable of holding the weight of the product.
Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick or cavity walls.
Seal the screw fixings to maintain the IP rating of the fitting.

Wiring

Having correctly identified the wiring from your existing light fitting, pull the wire through the hole and connect to the connection block inside the product in the following way:

Check that…

You have correctly identified the wires
The connections are tight
No loose strands have been left out of the connection block.

Commissioning

Ensure that the cable is not snagged and seal to maintain the IP rating of the product.
Fit the product back on to the mounting box and refit washers (D) and dome nuts (C), tighten dome nuts to secure.
To access the bulb, simply unscrew the shade. Unscrew the old bulb from the lampholder and replace with a new one. Then screw the shade back in place.
Replace fuse or circuit breaker and switch on. Your light is now ready for use.

www.saxbylighting.com

UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg