Aqara Cube T1 Pro Wireless Controller User Manual

Aqara Cube T1 Pro Wireless Controller

Product Information

The Cube T1 Pro is a wireless controller that supports two modes: Action Mode and Scene Mode. It can be used to perform various actions such as pushing, shaking, rotating, and tapping. In Scene Mode, it supports six different states (face 1 to 6) and various action control modes like rotating, picking up and holding, and tapping.

This product requires an Aqara Zigbee hub for operation. It can be used on any surface and can be connected to other smart devices for automation purposes. Some functions may require specific hubs. For more details, please visit www.aqara.com/support.

Aqara Cube T1 Pro is a new wireless controller, which supports two modes: Action Mode and Scene Mode. The action mode supports six modes: flip 90°, flip 180°, tap twice, push, shake and rotate. The scene mode supports six states (face 1 ~ 6/any side up) and various action control modes such as rotate, pick up and hold, and shake when face 1-6 up. “Triggered after one-minute inactivity” is supported in both modes. It can be placed on any surface, bound with the hub and work with other smart devices to perform various smart automations.

*This product requires an Aqara Zigbee hub. Some functions require specific hubs. For details, please see: www.aqara.com/support.

Product Usage Instructions

Quick Setup

1. Download the Aqara Home app from the Apple App Store or GooglePlay Store.
2. Make sure you have an Aqara Zigbee hub installed and added tothe Aqara Home app.
3. Open the battery cover of the Cube T1 Pro using the ejectortool.
4. In the app, click on the “+” button on the home page to enterthe Add Accessory page.
5. Select Cube T1 Pro and choose the hub you want to connectwith.
6. Follow the instructions in the app and wait for the hub toindicate a successful connection.
7. If the connection fails, you can try pressing the reset buttononce or picking up the Cube and shaking it.
8. For more information, please visit: aqara.com/support.
   • If the device fails to be added, please move the device close to the hub and try again.
   • Quickly press the reset button once, or pick up the Cube and shake it with If the hub gives a prompt sound, it indicates that the device can communicate effectively with the hub.
   • Different hubs give the prompt of successful connection in different ways. Please refer to the introduction of the hub.

Inspection and Installation

Before installation, make sure to inspect the Cube T1 Pro and check if all components are in good condition. Avoid installing it on metal surfaces for stable wireless communication. Effective distance test: Pick up the Cube and shake it or press the reset button. If the hub gives a prompt sound, it indicates that the device can communicate effectively with the hub.

• To ensure stable wireless communication, please avoid installation on metal surfaces.

Mode Switching

To switch between modes, open the Aqara Home app, go to the device page, click on the menu icon in the upper right corner, enter the device settings page, click on “More Settings,” and select the desired mode.

Battery Replacement

To replace the battery, use the ejector tool to open the battery cover, remove the old CR2450 battery (ensuring the positive electrode is facing upward), insert a new battery, and close the battery cover securely. Open the battery cover of Cube T1 Pro with the ejector tool, take out the battery, replace it with a new CR2450 battery (note that the positive electrode of the battery is upward), and then close the battery cover again.

Action Mode Instructions

• Rotate: Place the Cube on a surface and rotate it.
• Push: Place the Cube on a surface and push it.
• Tap: Pick up the Cube and tap it twice.
• Shake: Pick up the Cube and shake it back and forth quicklytwice.

Triggered after one-minute inactivity: The Cube is moved after stands still for one minute

Scene Mode Instructions

• Shake: Pick up the Cube and shake it back and forth quicklytwice.
• Pick up and hold: Pick up the Cube and hold it still.
• Pick up and hold (HomeKit only): Pick up the Cube and hold itstill. (This function is only supported by HomeKit.)

Specifications

• Product Model: CTP-R01
• Dimensions: 45×45×45mm (1.77×1.77×1.77in.) Net Weight: 76 g
• Battery: CR2450 (Replaceable) Wireless Protocol: Zigbee
• Operating Temperature: -10°C ~ 50°C (14°F ~ 122°F) Operating Humidity: :: 95% RH, no condensation Zigbee Operation Frequency: 2405- 2475MHz Zigbee Maximum Output Power :: 13 dBm

Online Customer Service: www.aqara.com/support Manufacturer: Lumi United Technology Co., Ltd.

Address: Room 801-804, Building 1, Chongwen Park, Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan Residential District, Nanshan District, Shenzhen, China

Warnings

1. This product is not a toy, please keep children away from this
2. This product is designed for indoor use only. Do NOT use in humid environments or
3. Beware of moisture, do NOT spill water or other liquids onto the
4. Do not place this product near a heat
5. Do not attempt to repair the product by yourself. All repairs should be performed by authorized
6. This product is designed only for improving the convenience of household life, and for status notifications. If the user violates the product instructions and this warning, the manufacturer is not responsible for any risks and property losses caused thereby.

Under normal use of condition, this equipment should be kept a separation distance of at least 0 mm between the antenna and the body of the user.

EU Declaration of Conformity

Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Cube T1

Pro,CTP-R01] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.aqara.com/DoC/

UK Declaration of Conformity

Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Cube T1

Pro,CTP-R01] is in compliance with Directive 2017 (SI 2017 No.1206, as amended by SI 2019 No. 696).

The full text of the UK declaration of conformity is available at the following internet address: http://www.aqara.com/DoC/

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

Symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

CAUTION

1. Risk of explosion if the battery is replaced by an incorrect type.

2. Dispose of used batteries according to the instructions.

3. Do not ingest battery, Chemical Burn Hazard.

4. This product contains a coin / button cell If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

5. Keep new and used batteries away from children

6. If the battery compartment does not close securely, stop using the product and keep it away from children.

7. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention

8. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion

9. Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas

10. A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas

FCC ID:2AKIT-CTP-R01

Federal Communications Commission (FCC) compliance statement:

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
   • This device may not cause harmful interference, and
   • this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The SAR limit of FCC is 1.6W/kg over 1 gram of tissue for use against the body. The highest SAR value reported under this standard during product certification when properly worn on the body is 0.17W/kg，This device was tested for typical body-worn operations with the edge of the device kept 0mm from the body.

IC:22635-CTPR01

IC NOTICE TO CANADIAN USERS

This device contains licence-exempt transmitter(s)/re- ceiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

• This device may not cause
• This device must accept any interference, including interference that may cause undesired operation of the

This Class B digital apparatus complies with Canadian

ICES‐003.

This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

The SAR limit of IC is 1.6W/kg over 1 gram of tissue for use against the body. The highest SAR value reported under this standard during product certification when properly worn on the body is 0.17W/kg，This device was tested for typical body-worn operations with the edge of the device kept 0mm from the body.

Scan to get the Zigbee Install Code on the last page of the manual.

*Please read this manual carefully and keep it in a safe place.

*If necessary, the contents of this manual will be modified or adjusted without special notice.

References

• Aqara Smart Device Product Support
• Aqara Smart Device Product Support
• Aqara - Smart Home Automation Devices for Better Living
• Aqara Smart Device Product Support
• Aqara Smart Device Product Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>