VISUAL LED 500 X 1000MM Rental LED Display Instruction Manual

June 12, 2024
VISUAL LED

VISUAL LED 500 X 1000MM Rental LED Display Instruction Manual
Rental LED Display

STEP 1: UNPACKING AND POSITIONING
A MINIMUM OF 2 PEOPLE FOR HANDLING AND ASSEMBLY
Unpacking Posting
USE A SOFT PROTECTIVE SURFACE (E.G. FOAM, CARDBOARD, CARPET, BLANKET, ETC.)
TO PLACE THE FRAMES OUT OF THE BOX.
Unpacking Posting
MAVOID ANY DAMAGE TO THE LEDS DURING UNPACKING AND HANDLING OF THE CABINETS. THESE DAMAGES ARE NOT COVERED BY WARRANTY

ALWAYS PLACE THE BACK OF EACH FRAME FIRST, PROTECTING THE LEDS.
Protecting Legs
AVOID IMPACT DAMAGES ON THE DISPLAY AREA.
Display Area
LED PANELS ARE EXTREMELY SENSITIVE ELEMENTS. DURING DISPLAY ASSEMBLY, EXTREME CARE MUST BE TAKEN TO AVOID DAMAGING THE LEDS.
Display Assembly
CHOSE A PERFECTLY LEVEL SURFACE OR STRUCTURE TO ASSEMBLE THE SCREEN ON
Screen On
BE SURE TO ORIENTATE THE CABINETS CORRECTLY.
VERTICAL POSITION: FOR SCREEN HEIGHTS OF 1 meter, 2m, 3m, 4m…
Cabinet Circulatory
HORIZONTAL POSITION: FOR SCREEN HEIGHTS OF 0’5meters, 1’5m, 2’5m, 3’5m…
Screen Hight

STEP 2: DISPLAY ASSEMBLY

CABINET LOCKING MECHANISMS

SET ONE CABINET OVER ANOTHER
Cabinet
PRESS LEVERS FROM THE UPPER CABINET AND INSERT MECHANISMS FROM THE LOWER FRAME.
Press Upper Cabinet
RELEASE UPPER LEVERS WITH MECHANISMS INSERTED
Release Upper Levers
LOCK MECHANISMS FROM THE LOWER FRAME. REPEAT THIS PROCEDURES FOR THE SIDE ANCHORAGES IF NECESSARY
Lock Lower Frame

IF A FRAME LOCKING MECHANISM DOES NOT APPLY TIGHTENING FORCE BETWEEN THE CABINETS WHEN IT’S ENGAGED, USE THE MECHANISM’S ADJUSTMENT SCREW

ADJUSTMENT SCREW
Adjust Screw

  1. WITH THE MECHANISM OPEN LOOSEN THE ADJUSTMENT SCREW WITHOUT REMOVING IT COMPLETELY. ADJUSTMENT SCREW
  2. MOVE THE LEVER TO ITS OPEN OSITION AS FAR AS POSSIBLE AND TIGHTEN THE SCREW.
  3. NOW INSERT THE MECHANISM AND CLOSE IT. CHECK THAT WHEN CLOSING THE LOCK MECHANISM IT IS APPLYING FORCE AND TIGHTENNING THE 2 FRAMES.

ANCHORING POINTS
Anchoring Points

ON THE BACK OF EACH CORNER OF THE CABINET THERE ARE M6 THREADED HOLES (4 HOLES PER FRAME).
Back Corner

IT IS POSSIBLE TO REMOVE THE CONNECTING MECHANISMS BY COMPLETELY TAKING OFF THE ADJUSTMENT SCREW, LEAVING 12MM DIAMETER THROUGH HOLES AVAILABLE ON ALL 4 SIDES.

WIRING OF THE LED DISPLAY

DATA WIRING
THE CABINETS MUST BE INTERCONNECTED IN SERIES WITH THE NETWORK CABLES. EACH FRAME HAS 2 NETWORK PORTS.

STANDARD NETWORK CABLE CAN BE USED TO MAKE THE CONNECTIONS
Wiring Instruction

POWER WIRING

INTERCONNECT THE CABINETS OF YOUR DISPLAY WITH THE SUPPLIED POWER CABLES.

DO NOT DRAW MORE THAN 3000W FROM THE SAME CONNECTION.
EACH FRAME HAS 2 POWER PORTS

POWER PORTS

Connection
DEPENDING ON THE SIZE OF YOUR SCREEN, MORE THAN ONE POWER MAINS CONNECTION MAY BE NEEDED TO POWER ALL THE FRAMES

MAINS CONNECTION
Connection Cable

LEDS INDICATORS

ALL CABINETS HAVE 2 INDICATOR LEDS ON THE REAR SIDE PROVIDING INFORMATION CODES ABOUT THE SCREEN STATUS

COLOR FUNCTION STATUS DESCRIPTION
RED Power LED Always ON Power supply is normal
Other ready for configuration
Green DATA LED 2 flashes every second Cabinet  with  correct

data connection ready to function normally
1 flash every 3 seconds| Ethernet cable connection is abnormal
3 Flashes every second| cable connection is normal, but no video source input is available
5 flashes every second| cabinet failed to load program. Using backup program
Other| ready for configuration

Led Indicators

END OF ASSEMBLY PROCESS

ASSEMBLY PROCESS ONCE YOU HACE COMPLETED THE WIRING YOU CAN PROCEED WITH THE DISPLAY STARTUP & SETUP PROCEDURE

CHANGING AN LED MODULE

LED SCREENS ARE MADE UP OF “CABINETS” OR FRAMES. EACH CABINET CONTAINS SEVERAL LED MODULES

STEP 1 : UNSCREW LED MODULE
Unscrew led Model
STEP 2 : LED MODULE EXTRACTION
Led Module Extraction
TO REMOVE THE AFFECTED MODULE FROM THE DISPLAY ARM FOLLOW THE STEPS OUTLINED AT THE END OF THIS MANUAL

  1. UNSCREW THE LED MODULE FROM THE CABINET
    Unscrew Led Model

  2. DISCONNECT THE LED MODULE CABLES TO SEPARATE IT FROM THE CABINET
    Unscrew Led Model
    WARNING: LED MODULES ARE DIFFERENT FOR EACH SIDE (LEFT HAND SIDE OR RIGHT HAND SIDE)

  3. IDENTIFY THE HAND OF A LED MODULE
    Identify Led Model

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals