BLACKLYTE ARCUS LED Strip Light User Manual
- June 12, 2024
- BLACKLYTE
Table of Contents
ARCUS LED Strip Light
Product Information
- The LED light bar is a versatile lighting device that can be controlled through a smartphone app.
- It features scene modes, brightness levels, and music modes.
- The product comes with RGB strips, a 12V controller, and an AC adapter.
- The LED light bar is designed for flat, smooth, and non-porous surfaces.
- Installation requires cleaning the installation surface, peeling off the protective film, firmly attaching the strip, reinforcing with provided clips and screws, and connecting the controller and strips.
- The device complies with Part 15 of the FCC Rules and has radiation exposure limits set forth for an uncontrolled environment.
Product Usage Instructions
-
Power On/Off: Press the power button to turn the LED light bar on or off.
-
Scene Mode: Press the scene mode button to switch between different preset modes.
-
Wireless Configuration Mode: Press and hold the scene mode
button for about 5 seconds to enter wireless configuration mode. This is required to add the device to the smartphone app. -
Brightness Levels: Press the brightness button to cycle through different brightness levels.
-
Music Modes: Press the music mode button to start or cycle through different modes that synchronize with music.
-
App Control: Scan the QR code or visit the App Store/Play Store to download the app for controlling the LED light bar.
Note: Before connecting the LED light bar, ensure that you understand the direction of the signal indicated by the arrows to avoid misplacement.
Installation Steps
Ensure the surface you are installing onto is clean and free from dust, oil, and fingerprints. Use the included alcohol-based cleaning cloth to wipe the surface before attaching.
- Make sure the surface is clean and dry. The RGB strips are best suited for flat, smooth, and non-porous surfaces.
- Peel off the protective film on the tape of the strip and firmly place it on the desired surface.
- Press down on the strip light for about 10-15 seconds to ensure proper contact and adhesion.
- Reinforce the installation by using the provided clips and screws.
- If you need to install the strip around corners, gently bend the strip over itself as shown in the instructions.
- Connect the 12V Controller to the AC Adapter and then connect your RGB Strips to complete the installation.
Warning: Any changes or modifications not expressly approved by the responsible party may void the user’s authority to operate the equipment. Please comply with FCC rules and maintain a minimum distance of 20cm between the radiator and your body during installation and operation.
Overview
Installation Steps
- Wipe the surface to make sure it’s clean and dry. Our RGB Strips are best suited for flat, smooth, and non-porous surfaces.
- Peel off the protective film on the tape, place the strip on the desired surface, and press down firmly.
- Stick the strip light and press down for about 10~15s to ensure contact.
- Reinforce via clips and screws provided.
- For corners, gently bend the strip over itself as shown above.
- Connect the 12V Controller to the AC Adapter and your RGB Strips to complete installation.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.