Gmarket ES22 Bluetooth Earphones User Manual
- June 12, 2024
- Gmarket
Table of Contents
ES22 Bluetooth Earphones
User Manual
ES22 Bluetooth Earphones
ES22 User manual
Thank you very much for choosing the ES22 Bluetooth earphones. To have a great
experience. please read this manual carefully before use.
Button definition
This product supports automatic master-slave switching, the headset uses a
touch structure design. and the key operation instructions are as following
Short press on L earphone or R earphone:
Short
press three times on the left side earbud :
Short
press three times on the right side earbud :Short press twice on the right side
earbud:
Short press twice on the left side earbuds: When incoming call, long press left /right side earbud for 2 seconds to reject the phone call
long press left or right earbuds for 5 seconds
Operations
Bluetooth connection
TWS Mode:
a Automatic boot, automatic pairing Earbuds will automatically turn on and
prompt out “power on and try to connect each other, once they have been taken
out from the charging case.
b When the pairing is successful
LED hdicators on the L earbuds wit blnkiig alternately and LED indicators
turned off on the R earbuds.
c Connect mobile phone
User can turn on Bluetooth function of the smart phone and search for the
Bluetooth device ES22 for pairing, .And LED indicators turn off on the left
earbuds once they connected with the smart phone.
Single earbud mode:
a Take out any earphone of the left or right from the charging case.the LED
indicator will blinking alternately
b
smart phone for pairing
The user can search for ES22 with a smart phone for pairing .The device will
prompt “connect”.The pairhg is successful, and the light on the earbuds turned
oft.
Note The left and nght earbuds wi be turgid on a Ito sane time when the
chargng case s opened. Vinen us rg the sagle earbud mode. the other earbud
needs to be turned dl (manualy paver off or put 6 in Me charging case and
close Vie top cover of tie chargng case).
Automatic reconnection:
After the earbuds is successfully connected to the terminal device, the next
time the earbuds is turned on. it can automatically connect back to the
terminal device that was connected last lime.
Incoming call
a. Incoming call
b. Answering / hang up the phone
Charging
Charge the earbuds
-
Earbuds will prompt out low battery voice alert once the batery level is too low.
-
Put the LRearbuds in the charging base and cbse the charging base cover, the earbuds will automatically enter the charging mode and the light display.
-
Earbuds full charge time:1.5 hours,the charging indicator light turis off after the earphone is fuly’ charged.
Reset to factory default
-
You can resetearbuds to factory default if you encounter pairing problems.When the earbuds off, tap and hold for 10 seconds to reset them to factory default Put them back to the charging base and take out again for painng.
-
Put the earbuds into the charging base, long press the reset button of the charging base,also can reset to factory default After resetting take out the earbuds for repairing.
Technical Parameters
- Chip solution:Actons
- Input charging voltage and curent:5V/1000MA
- Battery type: buit-in rechargeable ithium battery
- Battery capacity earbud battery 40mAh, charging base battery 400mAh
- Frequency response range:20HZ-20KHZ
- Sensitivity: 99+- 3dB
- Bluetooth version: V5.0
- Working range:10M
- Working hours: Earbuds: 4H;charging base: charging gycle: 4 tmes
ATTENTION
With the software and hardware updated, al the technical data and the mode of
operation showed on the manual coud be changed wihout pprior notice.
Security warning:
- Please store and use the produc under normal temperature, do not expose this apparatus to the rain or moisture.
- Do not throw away or disassemble for repair as it may cause safety problem
- Built-in ithium battery,do not discard or put itinto a fre
- Foryour health and to extend the life of the product, beter not to keep maximum volume on, to avoid injury of your hearing.
- In any emergency, Cut off the powerimmediately
- To always have a better performance,please charge in time once the battery is low.
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonableprotection against harmful
interference in a residential installation. This equipment generates, uses
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>