ezlo ESWV2 Smart Water Shut O Valve User Manual
- June 2, 2024
- ezlo
Table of Contents
- ezlo ESWV2 Smart Water Shut O Valve
- Specifications
- Product Usage Instructions
- FAQ
- Including the Water Valve to your Z-Wave Hub
- Association Group
- Connecting the Actuator to the Ball Valve
- Reset to factory settings
- Features
- What’s in the Box
- Smart Water Shut-OffValve Basics
- FCC Statement
- contact
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ezlo ESWV2 Smart Water Shut O Valve
Specifications
- Z-Wave Client Version
- Supports Association Group 1 with up to 5 nodes
- Supports Security 2 authenticated and unauthenticated, S0 and no security
- Works well with many Z-Wave compatible hubs, best when paired with Ezlo Hub
Product Usage Instructions
Including the Water Valve to your Z-Wave Hub
- Follow the manufacturer’s instructions to set your Smart Home Z-Wave Hub into Inclusion mode to add the Water Valve.
- Press the ‘Include/Exclude’ button once. The LED light will blink orange during the inclusion process and stop when finished.
- Continue with the inclusion process from your hub to complete the installation.
Excluding the Water Valve from your Z-Wave Hub
- Set your Z-Wave Hub into Exclusion mode.
- Press the ‘Include/Exclude’ button once. The LED light will blink orange during the exclusion process and stop when finished.
- Continue with the instructions from your hub to exclude the Water Valve.
Association Group
The Water Valve supports Association Group 1 with up to 5 nodes. It will react to specific events from associated devices and broadcast events to the hub using the same association group.
Connecting the Actuator to the Ball Valve
After plumbing the ball valve into your water system, disconnect the Smart Water Shut-Off Valve from its AC power cable, snap it into the ball valve, and reconnect it to a power source. Use an extension cord if needed.
Resetting to Factory Settings
To reset the Water Valve, press the ‘Include/Exclude’ button for over 10 seconds. The LED ring will blink orange, indicating the reset. This should only be done when the primary controller is inoperable.
FAQ
- Q: Can I use the Smart Water Shut-Off Valve without a Z-Wave Hub?
- A : No, the Water Valve requires a Z-Wave Hub for operation and integration into your smart home system.
- Q : Is professional installation necessary for the ball valve?
- A : Yes, the ball valve needs to be plumbed into your home’s water main and may require professional plumbing assistance. Contact a local plumber if needed.
Thank you for choosing the Ezlo Smart Water Shut-Off Valve (Z-Wave Client
Version)
You’ve taken the first step toward making your home smarter and safer.
Including the Water Valve to your Z-Wave Hub
- Follow the manufacturer’s instructions to set your Smar Home Z-Wave Hub into Inclusion mode to add the Water Valve.
- Press the ‘Include/Exclude’ button once. The LED light will blink orange during the inclusion process and stop when finished.
- Continue with the inclusion process from your hub to complete the installation. We want the set-up to be as easy as possible, but if you’re finding yourself in need of help, our outstanding customer care is here for you through the following channels:
Excluding the Water Valve from your Z-Wave Hub
- Set your Z-Wave Hub into Exclusion mode.
- Press on the ‘Include/Exclude’ button once. The LED light will blink orange during the exclusion process and stop when finished.
- Continue with the instructions from your hub to exclude the Water Valve
Association Group
The Water valve supports Association Group 1 with up to 5 nodes. The Water Valve will react when receiving a BASIC SET 0xFF/0x00 or NOTIFICATION Type 5 Event 2 or 0 from associated devices. The valve will broadcast events to the hub using the same association group. The Water Valve supports Security 2 authenticated and unauthenticated, S0 and no security. The Water Valve can be associated with any leak sensor with the same security type
Connecting the Actuator to the Ball Valve
Once the ball valve has been plumbed into your home’s water system, disconnect the Smart Water Shut-Off Valve from its AC power cable and snap it into the ball valve. Then reconnect it to a nearby power source. If your Smart Water Shut-OffValve is outside or plumbed away from a power source, you may need to use an extension cord.
Reset to factory settings
To reset the Water Valve, press the Include/Exclude button for over 10 seconds. The LED ring will start blinking orange. The valve will send a “Device Reset Locally Notification” to the hub it was included on. This procedure should only be used when the primary controller is inoperable
Features
Total asset protection from water damage. Easy to install. Easy to operate:
- Quick, easy control from anywhere when paired with a Z-Wave hub
- Weatherproof and ready for outdoor use, IP67 rated
- Designed for over 20,000 on/off cycles (over 50 years) with automatic, weekly self-testing
- Features local controls and manual override in the event of a power outage
- Fits any home size from MDUs to single-family residences
- Compatible with ¾”, 1”, and 1¼“ pipe sizes for easy installation in new construction
- Ball valves are sold separately
- Compatible with third-party Z-Wave hubs (it pairs as a device)
- Connects to 24V DC
- Supports s2 authenticated, unauthenticated, S0 and insecure inclusion
What’s in the Box
What you’ll need
- An Ezlo or other compatible Z-Wave Smart Home Hub
- ¾”, 1” or 1¼” Ezlo Ball Valve (sold separately)
- Home Wi-Fi Network
- iOS or Android Smartphone or Tablet
NOTE : The ball valve is plumbed directly into your home%E2%80%99s water main and may require professional installation. If you require assistance, please contact your local plumber before proceeding
Smart Water Shut-OffValve Basics
FCC Statement
Regulatory Information FCC Information:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o˛ and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit di˛erent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
- Please pay a˜ention that changes or modifications not expressly approved by Ezlo Innovation could void the user’s authority to operate the equipment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This
device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmi˜er may only operate using an antenna of a type and maximum (or lesser) gain approved
for the transmi˜er by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance 20cm between the radiator & your body.
Conformité ICES-003 d’Industrie Canada
Works well with many Z-Wave compatible hubs, works best when paired with an
Ezlo Hub
The Ezlo Smart Water Shut-Off Valve works with many Z-Wave compatible smart
home hubs but when paired with an Ezlo Plus or Ezlo Secure hub you get the
power of MiOS, the first operating system designed specifically for property
that lets you integrate all devices regardless of brand, automate devices with
advanced scene-creation tools, and visualize the status of all devices in your
smart home on our dynamic dashboard. No matter if you’re a mobile-first person
or have to go advanced we have the right solution for you.
contact
- Toll-free number 866 966 2272
- International number +1 702 487 9770
- support@ezlo.com
- support.ezlo.com
Hours of Operation:
Monday to Sunday from 7 AM – 10 PM Eastern EST (during non-daylight savings
time)