PHILIPS UD1005W Wire Harness 1XDT2 Ultinon Drive User Manual
- June 12, 2024
- Philips
Table of Contents
PHILIPS UD1005W Wire Harness 1XDT2 Ultinon Drive User Manual
INSTRUCTION
The Philips LED driving lights bears the official Philips Automotive Grade Quality seal. Philips Automotive Grade Quality products are designed and developed following strict quality-control processes (including applicable ISO norms). leading to consistently high production standards.
Important
Please read this user guide carefully before using your LED driving lights.
This guide contains important Health and safety information
If you need further assistance,please visit our website: www.philips.com/support Or visit your local Philips Dealer
For more information visit https://www.philips.com/LED-driving-lights
WARNINGS
-
Philips Ultinon Drive series are type-approved according to UN ECE R149 regulation and may therefore be installed and operated on public roads.
Please note: It is your own responsibility to ensure that the installation and use of the LED lightbars complies with applicable local and country-specific legal requirements. This includes, but is not limited to: Only install in pairs. The total of all reference numbers of the high beam headlights mounted on the vehicle may not exceed 100. Boost function is not permitted for use on public roads and can only be used off road. -
Do not look directly into the light source during operating due to the extremely light output.
-
Do not mount the lights in any location that obstructs the view of the driver; install it on location/devices which are designed for such purpose.
-
Professional installation is recommended.
-
Ensure that installation will not interfere with existing vehicle systems, airbag system sensors, forward and signal lighting, etc.
-
Ensure adequate clearance exists between the light and its wiring, between any moving or rotating parts of the vehicle (e.g., tires/wheels, suspension, doors, etc.).
-
Ensure the light is mounted at a safe distance from temperature-sensi- tive objects. Do not route wires along or near hot, sharp, or moving surfaces that might damage the wiring.
-
When laying out wire routing, stay clear of radio antenna and wiring to minimize radio interference.
-
Only operate under the specified voltages as mentioned in the specifications.
-
Use appropriately sized switches, wires, and circuit fusing.
-
Do not open the product and do not make any modifications to the lamp or cables; for any defective/malfunctioning devices, please contact our aftersales service.
-
The light becomes very hot during operation and remains hot after use. Do not touch the light when hot.
-
Do not clean with flammable substance or cover by flammable materials.
What In The Box
Discarded electrical products must not be disposed together with household waste. Please use recycling facilities. Contact your local authority or retailer for advice on recycling.
TOOLS REQUIRED
| UD1005W (1 light)| UD1006W (2 lights)| U01007W (1 fight)
---|---|---|---
UD5001L X1| 10A| 15A| /
UD5002L X1| 15A| 25A| /
UD5003L X1| 15A| 25A| /
UD5004L X1| 20A| 30A| /
UD5050L X1| 10A| 15A| /
UD5002C X1| 10A| 15A| /
UD5003C X1| 10A| 15A| /
UD2001R X1| 10A| 15A| /
UD2002R X1| 10A| 15A| /
UD5017L X1| /| /| 25A
TOOLS REQUIRED
Steps for installing fuse
Important: Need to insert the right fuse before installation
-
Open the fuse cap
-
Pick the fuse with right type
-
Insert the fuse with right type
-
Close the fuse cap
**Wiring Diagram UD1005W x1
**
With Switch
Without Switch
Wiring Diagram UD1006 x1
With Switch
Without Switch
Wiring Diagram UD1007W x1
With Switch
Without Switch
Warranty
Name: ————————————–
Address: ———————————–
Phone number: ————————–
Product number: ————————–
Purchasing date: ————————–
Lumileds is the warrantor of this product. 2022 Lumileds Holding B.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>