Current GEH6081 ESPL Sports Lighter Installation Guide

Current GEH6081 ESPL Sports Lighter

Product InformationThe LED Floodlight Sports Lighter (ESPL) is a high- performance lighting fixture designed for sports and outdoor applications. It provides bright and even illumination for sports fields, stadiums, and other large areas. The fixture is built with durable materials
and features advanced LED technology for energy efficiency and long-lasting performance. Key Features:

• Grounded fixture for safety and compliance with electrical codes
• Adjustable angles for precise aiming
• Chemical-free design for reduced environmental impact
• High light output and low heat retention

Product Usage Instructions

Storage & Handling:

1. Store the packaged units in a covered dry area to protect them from moisture and damage.
2. Check for any visible damage before installation. If any damage is found, contact the supplier or manufacturer.
3. Handle the units carefully and avoid impacts or dropping, as it may cause internal damage.
4. Do not stack the units to prevent potential damage or deformation.

Sports Lighter Installation A. Install Wire Rope:

Refer to the provided picture to install the wire rope that can be used for lifting the fixture or securing it to the mounting structure while adjusting the fixture angle of aim.

B. Adjusting Angle:

Caution: Do not remove the socket head cap screws. Loosen the 2 socket head cap screws with a 10mm hex drive bit gradually until adjustment can be made. Once the desired angle is achieved, tighten using a torque wrench set at 26 foot pounds. Avoid aiming upward more than a 45-degree angle to prevent debris from filling the lens.

C. Mounting Hardware:

Important: The suggested mounting hardware is not provided and should be supplied by others. You will need: – 1 bolt and nut that is 3/4-10 SAE Grade 8 or ASTM A325, galvanized and not waxed or lubricated. – 2 3/4 galvanized washers. – Use the bolt, washers,
and nut on the center mounting hole of the yoke. – Tighten them to a torque of 300 foot pounds.

Power & Dimming Cord:For any questions or assistance regarding power and dimming cords, contact LED.com at 1-877-843-5590 or email techsupport@currentlighting.com.

Note: These instructions may not cover all details or variations in equipment installation, operation, or maintenance. For further information or specific concerns, please refer to the manufacturer’s support.

Current Lighting Solutions, LLC 25825 Science Park, Suite 400 Beachwood, OH 44122

Web: LED.com

BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future use.

WARNING
Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to do so may increase the RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH. Install and use so fixture failures do not cause a hazard and use only in environments for which the product is specifically marked.

WARNING
Dangerous voltage exist within the unit and all precautions usually observed in handling high voltage equipment should be observed when replacing light engine or otherwise servicing luminaires. Disregarding this warning could result in electrical shock and possible injury to the individual installing or servicing this equipment. Installation and servicing should be done by qualified personnel.

WARNING
This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

WARNING
Follow ALL luminaire recommendations, product markings, instructions, restrictions and warnings regarding luminaire operation and burning position. Luminaire label shows electrical and environmental requirements and restrictions.

Note: This luminaire is designed for oudoor lighting applications and ambient temperatures not exceeding 40oC (104oF).

• All electrical work must be done by a qualified electrician.
• Turn off electric power to all affected circuits and allow to cool before installation or servicing.
• A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optical system. Any accumulation of dust or dirt should be removed regularly.
• Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact your Lighting distributor or techsupport@currentlighting.com or 864-678-1000
• Give instructions to facility owner/manage for future reference.

Storage & Handling

Sports Lighter Installation

Tools Required

Torque Wrench with foot-pounds and inch-pounds settings
Hex socket that is 1-1/8”
10mm hex drive bit.

• The above picture shows how to install the wire rope that can be used for lifting the fixture. This can also be used to secure to the mounting structure while adjusting the fixture angle of aim.
• The above picture shows the angles of adjustment. CAUTION: Do Not Remove the socket head cap screws. To make the adjustment loosen the 2 socket head cap screws with a 10mm hex drive bit a little at a time until adjustment can be made. Once the angle has been achieved tighten using a torque wrench with the setting at 26 foot pounds. To keep lens from filling from debris do not aim upward more than 45 degree angle.
• IMPORTANT: The suggested mounting hardware has not been provided and are “supplied by others”: Qty 1 of a bolt and nut that is 3/4”-10 SAE Grade 8 or ASTM A325. They need to be galvanized and should not be waxed or lubricated. Also will need qty 2 of 3/4” galvanized washers. The bolt, washers, and nut should be used on the center mounting hole of the yoke. They need to be tightened to a torque of 300 foot pounds.

Power & Dimming Cord

Power & dimming cord has been provided with the following wires

• Black for Line
• White for Neutral
• Green for Ground
• Purple for Dimming+
• Pink for Dimming-

Questions:
Web: LED.com
Phone: 1-877-843-5590
Email: techsupport@currentlighting.com
Current Lighting Solutions, LLC 25825 Science Park, Suite 400 Beachwood, OH 44122

These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be met in connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, the matter should be referred to Current.

LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions.

Page 3 of 6
(Rev 05/28/23)
GEH-6081-LED-Evolve-Sports-Lighter-Floodlight-InstallGuide_R01

References

• guideled.com - Registered at Namecheap.com
• LED Commercial Lighting and Lighting Controls | Current - GLI Brands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>