SIRIUS SLTC97 S.A.M.S JEEG TW Black Wall Hood Instruction Manual

COMMERCIAL INFORMATION FOR THE CONSUMER
INSTALLATION, USE AND MAINTENANCE INSTRUCTION
SLTC97 S.A.M.S.
SLTC120 S.A.M.S.

TECHNICAL INFORMATION

SLTC97 S.A.M.S JEEG TW Black Wall Hood

WARNINGS

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room)
• When the cooker hood is used in conjunction with appliances supplied with energy other than electric (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room (not applicable to appliances that only discharge the air back into the room).
• It is not allowed to cook food over open flames (flambé) or operate gas hobs without pots or pans on them under the hood itself (the flames sucked into the hood might damage the appliance).
• Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood.
• Before carrying out any kind of maintenance or cleaning, disconnect the hood from the mains supply.
• The minimum safety distance between the cooker top and the extractor hood is 650 mm.
• If a stationary appliance is not fitted with a supply cord and a plug, or with other means of disconnection from the supply mains, it is necessary to predict a contact separation in all poles that provide full disconnection under overvoltage category III conditions.
• Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood.
• All appliances are Class I, so it is necessary to check that the domestic power supply guarantees adequate earthing.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
• Children shall not play with the appliance
• Cleaning and user maintenance shall not be made by children without supervision.
• Failure to carry out cleaning as indicated will result in a fire hazard.
• Before commencing the installation, check that all components are not damaged, otherwise contact the dealer and do not continue with the installation.
• Accessible parts of the hood may become hot when used with cooking appliances.
• In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks. · For hood models with EXTERNAL MOTOR, the external motor is powered directly by the kitchen hood.
• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• Repairs must be performed only by an authorized technician. Always disconnect the hood before carrying out cleaning or maintenance operations.
• Never use steam or high-pressure devices for cleaning your hood.
• Respect the guidelines for cleaning and replacement of grease filters. Accumulated deposits of grease are a fire hazard.
• Never use the cooker hood without the grease filters.

USES

Sirius range hood is equipped with an air purification system inside the upper chimney. This system is made up of an air quality sensor, 2 ionizers and a valve activated by a micromotor, allowing to exhaust fumes outside (ducting version) or towards charcoal filters and side ionizers (filtering version).
This range hood is equipped with a new Touch control having a S.A.M.S. button, indicating always the air quality through the color variation: White: clean air; Blue: good air; Orange: medium air; Red: bad air. By pressing the button “S.A.M.S.”, you can change the version of the hood from ducting (open valve and air exhausted outside) to filtering and purifying (closed valve; fumes go out through the side grills of the chimney; the air returns to the kitchen once filtered and purified thanks to high efficiency charcoal filters and ionizers).

The Smart Air Management System is usually set in ducting version. The valve is open and fumes go outside through a ducting system. After installation, the product works as a standard range hood, with a white colour rear-lighted touch control.

After or while cooking, if the button (S.A.M.S) highlights a bad air quality, you can activate the Smart Air Management system by pressing this button. The backlight of the touch control changes from white to blue colour. The valve closes, the ionizers start functioning and the air returns to the kitchen through the chimney side grills.

The process of filtration and air purification takes place through 2 High Performance charcoal filters and 2 ionizers. You can keep on using all the product functions as usual (change in speed, lights, etc). You can activate this new system even when the product is switched off, in case of bad quality air. By pressing the button “S.A.M.S.”, the range hood sets in filtering mode with motor at 1st speed. You can permanently set the Smart Air Management function during installation. You just have to hold down the button “S.A.M.S” for at least 3 seconds in order to set the product in ducting or filtering version.

INSTALLATION

Before installing the appliance, make sure that none of the parts is damaged in any way. In case of damaged parts, contact your retailer and do not proceed with installation. Read all of the following instructions with care before installing the appliance.

• Use an air outlet pipe of the shortest possible length.
• Limit the number of pipe bends.
• Use a material approved by standards and regulations.
• Avoid any sudden changes in pipe section (recommended constant diameter: 150 mm or equal surface area).

Wall stirrup-fixing

• By using the special drilling jig (Fig. 1X), perforate the wall according to the pattern indicated by the jig itself, and pay attention in order not to damage water pipes and electric wires. Perforation should be performed with a Ø 8 mm wall-drill. Then insert into the proper plastic reinforcements (Fig. 1A). The hood-bearing stirrup (Fig. 1S) can be applied by using the screws provided with the equipment (Fig. 1B). Now hook the cooker hood onto its bearing (Fig. 2) and then adjust horizontally and vertically the position of the appliance by acting on the special metric screws (Fig. 3V,T). After the appliance is adjusted, fix it by inserting and tightening the safety screws properly. Remove the grease filter in order to reach the appliance inner side. The grease filter is removed by following the instructions given in the maintenance section. Definitively secure the product to the wall by using the screws provided, as shown in fig. 1C. Refit the grease filter.

Warning!
Before connecting the flexible exhausting pipe to the motor, make sure the stop valve, which is on the air outlet of the motor, can swing.

Valve assembly fixing
After installing the hood, take the valve unit and place it above the ducting (fig. 4-5).
The installation height must be within the range (min-max) indicated in the technical drawing of the hood (see fig. 6-7).
Important precaution, before making the fixing holes, position the chimneys above the hood and make the grids of the upper chimney coincide in correspondence with the charcoal filters of the valve.
Fix the valve to the wall using the holes see fig. 8, by the screws (fig. 9B) and plugs (fig. 9B) supplied (fig. 9).
Connect the electric cables as showed in fig.10 (ionizer cable fig.10A, air quality sensor cable fig.10B, valve activation motor cable fig.10C, ground cable fig.10D).

Fixing the ornamental chimney

• Before fixing the chimney, place the electric feeding equipment into the ornamental pipe and provide it with a hole for the air outlet if the appliance is used in its sucking version.
  Fix the pipe-bearing stirrup (Fig. 11Y) to the wall or ceiling by using the proper reinforcements and screws in equipment. Connect the cooker-hood flange with the evacuation hole by using a proper pipe.
  Now mount the inferior chimney by inserting it through the front side of the cooker hood and then turning it down until it is fixed inside (Fig. 12).

WORKING

SLTC97 – SLTC120 (Fig. 13)
A: S.A.M.S. switch ON/OFF (please look at chapter “USES”)
B: Light switch On/Off
C: Reduce speed
D: Luminous telltale
E: Incrase speed
F: 10 – minute timer
With the hood off, by pressing the E button (see fig. 13E), the engine is started at 1st speed, the valve is positioned as in the fig. 19, the product is in the ducting version. The LEDs are all white except for LED A (see fig. 13A) which is of the RGB type and constantly indicates the quality of the air. The aspirated fumes are channeled towards the air outlet duct. Ionizer not powered. It is possible to change the speed of the suction fan, set and adjust the lights.
By pressing the “S.A.M.S.” key A see fig. 13, with the hood on, valve is closed as shown in the figure 20.
The aspirated fumes are diverted to the ionizers, which will be fed, and to the carbon filters. It is possible to change the speed of the suction fan, set and adjust the lights. The LEDs (except key A – D, see fig. 13) change to BLUE color. By pressing the “S.A.M.S.” key A see fig. 13, with the hood off, the valve is positioned as shown in the fig. 20 and the first speed of the suction fan is set.
By keeping button A (fig. 13A) pressed for more than 3 seconds (hood on or off), the product switches from suction to filtering version or vice versa, permanently. By activating the product (motor ON) you are already in the previously set mod.
The products are endowed with an electronic de vice which allows the automatic switching off after 4 hours working from the last operation.

DIMMABLE LIGHTS FUNCTION
THIS FUNCTION PROVIDES FOR LIGHTS DIM MABILITY, RANGING FROM 20% TO 100% , BY CONTINUOUSLY PRESSING THE LIGHT KEY ON THE REMOTE CONTROL. FUNCTIONS ARE THE FOLLOWING:

• HOOD LIGHT OFF – SHORTLY PRESS THE KEY – LIGHT ON AT 100%.
• LIGHT ON AT 100% – SHORTLY PRESS THE KEY – LIGHT OFF.
• LIGHT ON AT 100% – CONTINOUSLY PRESS THE KEY – BRIGHTNESS REDUCTION.
• RELEASING THE KEY DURING REDUCTION OR INCREASE – LIGHT KEEPS THE LUMI NOUS INTENSITY REACHED.
• LIGHT ON – DIMMED – CONTINOUSLY PRESS THE KEY – BRIGHTNESS IS INVERTED IF COMPARED TO THE PREVIOUS FUNCTION.

COLOUR TEMPERATURE SETTING
Make sure that the lights and the fan are off. Holding down the TIMER key will turn on the light at the previously set colour temperature. Press and hold the Light key to change the colour temperature. As long as the key is kept pressed, the colour temperature is changed from warm to cold, just leave the Light key to select the desired colour. Exit the colour temperature selection function by pressing the ON/OFF key.

TIMING
As a result of the new EU65 “Energy label” and EU66 ” Ecodesign” regulations issued by the European Commission, which came into force as from January 1st, 2015 , our products have been adapted to comply with these new requirements. All of the models complying with the energy label requirements, are equipped with new electronics including a timer device for suction speeds control, when the air capacity exceeds 650m³/h.
Internal motor models, with maximum air capacity higher than 650m³/h, are equipped with a timer device that automatically switches the suction speed from 4th to 3rd speed, after 5 minutes operation.
External motor models are equipped with remote motors that , as for internal motor versions, include a timer device that switches down the suction speed when it exceeds 650 m/h. (See External Motors Instructions).
Remote motors, whose air capacity exceeds 650m³/h at both 4th and 3rd speed , will have the following by default timer control functions: The suction speed is automatically switched from 4th to 2nd speed, after 6 minutes operation. If the appliance is working at 3rd speed, it is automatically switched to 2nd speed, after 7 minutes operation. Operation speeds can also be changed during operation. The energy consumption of the appliance in stand ­ by mode is lower than 0.5W.

MAINTENANCE

• An accurate maintenance guarantees good functioning and long-lasting performance.
• Particular care is due to the grease filter panel. It can be removed by pushing its special handle toward the back-side of the cooker hood and turning the filter downwards so to unfasten it from its slot (Fig. 14 e 15). To insert the filter just perform the opposite operation.
  After 30 hours working the grease filter saturation is signalled by the flashing of the two central push buttons (Fig. 13D). Press the timer button to reset .
  The grease filter needs cleaning by regular handwashing or in dishwashers every two months at least or depending on its use.
• In case the appliance is used in its filtering version, the HP active coal filter (Fig. 16A) needs to be periodically replaced. The HP active coal filter is removed by first lowering the upper chimney (fig. 16) and then pulling the special plastic tab of the carbon filter releasing it from its seat (fig. 17). The HP active coal filter is mounted in the reverse operation. The HP active coal filter needs replacing depending on the use, but however every six months at least.
• To clean the appliance itself tepid water and neutral detergent are recommended, while abrasive products should be avoided. For steel appliances specialized detergents are recommended (please follow the instructions indicated o the product itself to obtain the desired results).
• If the supply cord is damaged, it must be replaced by the manufacturer or its sevice agent or a similarly qualified person in order to avoid a hazard.

* Substitution of the LED bar:
Using an appropriate tool, remove the LED bar from its seat (refer to Fig. 18), disconnect it electronically using the appropriate connector then substitute it with a LED bar with same characteristics.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. This appliance is marked according to the European directive 2012/19/EC on  waste electrical and electronic equipment (WEEE).

Importr:
MULTIKOMPLEX BUDAPEST KFT.
A páraelszívók szakértje… 1995 óta
H-1211 Budapest Mansfeld Péter utca 27. (Volt Bajáki Ferenc utca)
tel.: +(36-1) 427 0325, +(36-1) 427-0326; fax: +(36-1) 427 0327
www.multikomplex.hu

90007097999 – EM 01/23

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>