Aqara T1 Zigbee Water Leak Sensor User Manual

: June 13, 2024
: Aqara

Table of Contents

Aqara T1 Zigbee Water Leak Sensor
Product Information
Product Usage Instructions
Product Specifications
Product Introduction
Product Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Aqara T1 Zigbee Water Leak Sensor

Product Information

The Aqara Water Leak Sensor T1 is a device that uses the Zigbee 3.0 wireless communication protocol to detect water leakage and soaking. It can detect two states: from waterless to water and from water to water-break. When a leakage or soaking occurs, it will send timely alarm information through the app and can control other smart hardware products through the hub device’s linkage. Please note that an Aqara hub is required, and some functions may require specific models of the Aqara hub. For more details, please visit
www.aqara.com/support.

Product Usage Instructions

Before activating the accessory, make sure you have downloaded the Aqara Home app and installed the Aqara hub.
Open the app, tap “Home,” and then tap “+” in the top right corner to enter the “Add Device (Accessory)” page.
Select “Water Leak Sensor T1” and follow the instructions to add it.
If the connection fails, move the accessory closer to the hub and try again.

Product Specifications

Model: WL-S02D
Battery: CR2032
Manufacturer: Lumi United Technology Co., Ltd.
Address: Room 801-804, Building 1, Chongwen Park, Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan Residential District, Nanshan District, Shenzhen, China
Online Customer Service: www.aqara.com/support
Email: support@aqara.com

Warnings

This product is NOT a toy. Keep children away from this product.
This product is designed for indoor use only. Do NOT useoutdoors.
Do NOT place this product near a heat source. Do NOT place it in an enclosure unless there is normal ventilation.
Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional.
This product is only suitable for improving the entertainment and convenience of your home life and reminding you about the device status. It should NOT be used as security equipment for home, building, warehouse, or any other places. If you violate the product use instructions, the manufacturer will NOT be liable for any risks and property losses.

Caution

Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Do not ingest the battery as it can cause severe internal burns and even death if swallowed.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you suspect batteries have been swallowed or placed in any body cavity, seek immediate medical attention.
Under normal use conditions, keep a separation distance of at least 20cm between the antenna and the user’s body.

Product Introduction

Aqara Water Leak Sensor T1 is a device that may detect water leakage and soaking based on the Zigbee 3.0 wireless communication protocol. It may detect two states, namely from waterless to water, from water to water-break. When leakage or soaking occurs, it may timely push the alarm information through the app, and control other smart hardware products through the linkage of the hub device.

*An Aqara hub is required. Some functions require specific models of the Aqara hub. Please visit www.aqara.com/support for more details.

Aqara-T1-Zigbee-Water-Leak-Sensor-01

Device Binding & Initialization
Before activating the accessory, please make sure you have the Aqara Home downloaded and Aqara hub installed. Please open the app,”tap Home”and then tap”+”in the top right corner to enter”Add Device (Accessory)”page. Select”Water Leak Sensor T1″, and add it according to instructions.
For details, please see www.aqara.com/support or scan the QR code below to get the detailed electronic manual.

If the connection fails, please move the accessory closer to the Hub and try again

Product Specifications

Water Leak Sensor T1

Model: WL-S02D: Battery: CR2032
Wireless Protocols: Zigbee 3.0
Dimensions: ⌀50 × 50 × 15 mm (1.97 × 1.97 × 0.59 in.)
Zigbee Operation Frequency: 2405-2480 MHz
Zigbee Maximum Output Power ≤ 13 dBm
Operating Temperature: -10°C ~ 55°C (14°F ~ 131°F) Operating Humidity: 0 ~ 100% RH, no condensation
What is in the Box: Water Leak Sensor T1 × 1, User Manual × 1

Manufacturer: Lumi United Technology Co., Ltd.
Address: Room 801-804, Building 1, Chongwen Park, Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan Residential District, Nanshan District, Shenzhen, China Online Customer Service: www.aqara.com/support
Email: support@aqara.com

Warnings

This product is NOT a toy. Please keep children away from this product.
This product is designed for indoor use only. Do NOT use outdoors.
Do NOT place this product near a heat source. Do NOT place it in an enclosure unless there is normal ventilation.
Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional. This product is only suitable for improving the entertainment, convenience of your home life and reminding you about the device status. It should NOT be used as security equipment for home, building, warehouse or any other places. If a user violates the product use instructions, the manufacturer will NOT be liable for any risks and property losses.

Caution

Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. The equipment is only suitable for mounting at heights ≤ 2 m.

Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.

EU Declaration of Conformity
CE Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Water Leak Sensor T1, WL-S02D] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.aqara.com/DoC/

UK Declaration of Conformity
Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Water Leak Sensor T1, WL-S02D] is in compliance with Directive 2017 (SI 2017 No. 1206, as amended by SI 2019 No. 696).
The full text of the UK declaration of conformity is available at the following internet address: http://www.aqara.com/DoC/.

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

Symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
FCC ID: 2AKIT-AS014

Federal Communications Commission (FCC) compliance statement:
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC:22635-AS014
IC NOTICE TO CANADIAN USERS

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s licence-exempt RSS(s).

Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES‐003.
This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.