AirCool AC-50CM Stand Fan Instruction Manual

AC-50CM Stand Fan
Instruction Manual MODEL NO.: AC-50CM
Operating Instructions
Save these instructions Read rules for safe operation carefully

PARTS DESCRIPTION

STAND ASSEMBLY

1. REMOVE ALL PARTS FROM CARTON
2. REMOVE PLASTIC COVERING FROM STAND LEGS. AND SNAP TOGETHER THE TWO PARTS OF STAND AS SHOWN

COLUMN ASSEMBLY

1. LOOSEN THE EXTEN SION POLE TIGHTENER BY TURNING COUNTER-CLOCKWISE
2. PUSH UP THE STEEL EXTENSION PIPE.WHICH IS STORED IN SIDE THE COLUMN POLE. TO DO THIS. PUSH THE EXTENSION PIPE UP.BY INSERTING A SCREWDRIVER IN TO THE BASE OF THE COLUMN PUSH UNTIL YOU CAN SEE THE STEEL EXTEN SION PIPEABOVE THE TIGHTENER PULL THE PIPE UP POLE TIGHTENER CLOCKWISETHIS WILL LOCK THE EXTENSION POLE IN PLACE
3. ATTACH THE COLUMN TO THE STAND LEGS BY REMOVING THE 4 SCREWS. LINE UP THE FOUR SMALL HOLES. IN THE COLUMN BASE.WITH THE FOUR SCREW HOLES IN THE CROSS STAND LEGS. INSERT THE SCREWS AND TIGH TEN.
4. REMOVE THE ENTEN SION POLE TIGHTENER BY TURNING COUNTER-CLOCKWISE. PLACE THE STAND ORNAMENT OVER THE EXTENSION PIPE AND DROP DOWN OVER THE COLUMN ANDALIGN THE SLOTS TO FIT OVER THE STAND LEGS.
5. REPLACE YOUR EXTENSION POLE TIGHTENER AND TIGHTEN SO THE EXTENSION PIPE DOES NOT SLIDE DOWN AS YOU MOUNT THE MOTOR AND SWITCH HOUSINGASSEMBLY

MOTOR AND SWITCH HOUSING ASSEMBLY

1. LOOSEN THE THUMB SCREW AT THE BOTTOM REAR OF THE SWITCH HOUSING.
2. PLACE SWITCH HOUSING AND MOTOR ASSENBLY ON EXTENSION PIPE 2
3. TIGHTEN THE THUMB SCREW SO THAT IT ENGAGES INTO THE GROOVE ON THE EXTENSION PIPE.
   

CAUTION: DO NOT LOOSEN THE EXTENSION PIPE TIGHTENER BEFORE THE SWITCH HOUSING IS ATTACHED TO THE EXTEN SION POLE THES MIGHT RESULT IN IN JURY OR DAMAGE TO THE MOTOR AND SWITCH HOUSING ASSEMNLY

BLADE AND GUARD ASSEMBLY

1. REMOVE THE BLUE PLASTIC SPINNER KNOB BY TURNING CLOCKWISE.

2. REMOVE THE WHITE GUARD NUT FROM THE MOTOR HOUSING BY TURNING COUNTER CLOCKWISE.

3. ASSEMBLE THE REAR GUAED SCREEN TO THE MOTOR HOUSING MAKING CERTAIN THAT THE THREE PLASTIC PINS ENGAGE THE IV1ATCHIING HOLES IN THE REAR GUARD SCREEN.
   FASTEN IN PLACE BY REPLACING THE GUARD NUT AND TURNING INA CLOCKWISE DIRECTION UNTIL TIGHT.

4. SLIDE BLADE ONTO THE MOTOR SHAFT

5. SCREW ON THE BLUE PLASTIC SPINNER INA COUNTER CLOCKWISE DIRECTION TO RETAIN THE BLADE.

6. HANG THE FRONT GUARD SCREEN ON TO THE REAR GUARD AND LOCK IN PLACE MTH THE FOUR METAL CUPS ATTACHED TO THE FRONT GUARD SCREEN

OPERATION

1. SPEED ON PUSH BUTTON SWITCH
3–High
2– Med
1—Low
0–Off
NOTE: DO NOT Push two buttons at once. This may result in petmanent damage to the switch.

OSCILLATION

1. OSCILLATION OF FAN IS CONTROLLED BY PULLING UP OR PU SHINS DOWN THE OSCILLATION KNOB ON THE MOTOR COVER.

2. OSCILLATING ANGLE:
   THE CENTER OF THE OSCILLATION ANGLE CAN BE CHANG ED BY TURNING THE FAN HEAD IN RELATION TO THE. SWITCH BOX.
   NOTE: Oscillation knob must be In the “up” position to sdjust.

3. TILTING
   THE TILT ANGLE CAN BE ADJUSTED BY TIL TING THE HEAD FORWARD OR BACK WARD,

4. HEIGHT ADJUSTMENT.
   THE HEIGHT OF THE FAN CAN BE ADJUSTED BYLOOSING THE HEIGHT ADJUST mem- KNOB CAREFULL. RAISING OR LOWERING THE FAN THEN FIRMLY RETIGHTEN THE SNOB TO LOCK IN PLACE.

CLEANING FAN

NOTE ALWAYS UNPLUG FAN BEFORE CLEAMNG
Plastic partss hould be cleaned with mild soap and a damp cloth or spo.nge.Thoroughiy remove soap Mm with a clean damp cloth to disassemble each part reverse the order of assembly.

MAINTENANCE.

NOTE ALWAYS DISCONNECT THE CORD FROM THE ELECTRICAL OUTLET BEFORE STARTING TO CLEAN YO../Ft FAN
Wipe the extener surfaces of the fan occasionally with a moistened ototh(not dripping wet) with a solution of mild detengent and water. Dry the case thoroughly with a soft dry cloth before operating the fan
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE INTERIOR OF THE FAN AS THIS COULD CREATE A FIRE OR ELECTRIC SHOCK HAZARD.
No other user maintenance is requited or recommended Store fan in a vean dry place when not in use.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>