Bray SSM Series Pressure Independent Control Valve User Manual
- June 13, 2024
- Bray
Table of Contents
- Technical Specifications
- Safety Instructions
- Kit Components
- ASSEMBLY
- Overview
- Simple Set Max – ANSI 125 Flow Rate Charts
- Simple Set Max – ANSI 250 Flow Rate Charts
- Simple Set Max – ANSI 125 Dimensions – 2-1/2″ – 12″
- Simple Set Max – ANSI 250 Dimensions – 2-1/2″ – 12″
- CUSTOMER SERVICES
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Bray SSM Series Pressure Independent Control Valve
FOR MORE INFORMATION ON THIS PRODUCT AND OTHER BRAY PRODUCTS PLEASE VISIT OUR WEBSITE –www.braycommercialdivision.com
Technical Specifications
Technical Specifications – Valve
Service| Hot Water, Chilled Water, 50-50 Glycol Solutions
Size Range| 2-Way| 2-1/2″ through 12″ (DN 65 to 300)
Cold Working Pressure| 2-1/2″ through 12″ – 232 PSI @ 100˚F, ANSI 125
2-1/2″ through 12″ – 500 PSI @ 100˚F, ANSI 250
Media Temperature Range| 2.5″ to 5″| 32°F to 248°F (0°C to 120°C)
6″ to 12″| 32°F to 230°F (0°C to 110°C)
Min. Operational ∆P| Refer to Flow Rate Charts on Pages 9 thru 16
Max. Operational ∆P| 116 PSID (800kPa)
Max. Close-Off Pressure| 116 PSI (800kPa)
Valve Operation| Push down to close, Normally Open
Shut-Off Leakage| <ANSI Class IV (0.01%)
Flow Rate Range| 19.27 to 2641 GPM
Stroke| 2.5″ & 3″| 0.79″ (20mm)
4″ & 5″| 1.58″ (40mm)
6″ & 8″| 1.69″ (43mm)
10″ & 12″| 1.89″ (48mm)
Rangeability| >100:1
Flange Connections| ANSI 125 & ANSI 250
Test Ports| 1/4” NPT
Materials| Body| 2-1/2″ thru 6″ – Cast Iron 8″ thru 12″ – Ductile Iron
Flow Regulation Unit| Stainless Steel
Diaphragm| Reinforced EPDM (Ethylene Propylene Diene Monomer)
Spring| Stainless Steel
O-Rings| EPDM
Warranty| 5 Years limited from time of shipment.
Weights| See Dimensions – Pages 17 & 18
Disclaimer – The pipe system shall be properly ventilated to avoid risk of air pockets. Glycolic mixtures up to 50% are applicable (both ethylene and propylene). Bray can accept no responsibility if another actuator is used instead of the Bray actuator recommendation: Water treatment to VDI 2035.
Simple Set Max – Installation, Operation & Maintenance Manual Continued
Safety Instructions
– Definition of Terms Read, Follow and Save these instructions
WARNING
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
NOTICE
Used without the safety alert symbol indicates a potential situation which, if
not avoided, may result in an undesirable result or state, including property
damage.
Qualified Personnel
A qualified person in terms of this document is one who is familiar with the
installation, commissioning and operation of the device and who has
appropriate qualifications,
such as:
- Is trained in the operation and maintenance of electric equipment and systems in accordance with established safety practices.
- Is trained or authorized to energize, de-energize, ground, tag and lock electrical circuits and equipment in accordance with established safety practices.
- Is trained in the proper use and care of personal protective equipment (PPE) in accordance with established safety practices.
- Is trained in first aid.
- In cases where the device is installed in a potentially explosive (hazardous) location – is trained in the operation, commissioning, operation and maintenance of equipment in hazardous locations.
Product Description
Bray’s Simple Set Max combines an externally adjustable dynamic balancing
valve with a full authority modulating control valve.
Available in both ANSI 125 and ANSI 250 configurations.
Function
The air temperature of the Air Handling Unit is controlled by a sensor in the
outlet. When the control system calls for higher or lower temperature on the
air outlet, the PICV opens or closes to increase or decrease the flow through
the coil. The power output from the coil follows a parabolic curve where often
an EQ% valve/actuator characteristic is chosen to have a direct relation
between the input control signal and power output.
Figure 1 Installation
Bray’s Simple Set Max can be mounted in either the supply or the return line.
Installation of strainers and isolation ball valves are recommended. The
temperature in and about the actuator should not be below 14˚F (-10˚C). We
recommend mounting downstream to the coil to minimize temperature extremes.
Figure 2 Mounting Positions
Actuator mounting positions for GA Series Actuators
Precautions:
Wear safety glasses and wear safety glasses and appropriate safety equipment before performing any of the listed tasks.- Assure all components are present before assembly.
Kit Components
Tools and Equipment Required
22 & 24 mm Wrench (or Crescent Wrench)
6 mm Allen Wrench
2.5 mm Allen Wrench
PRE-ASSEMBLY
NOTE:
ASSEMBLY
-
Inspect the actuator for any sign of physical damage.
-
Using the actuator manual override assure actuator full shaft extension retraction. If spring return, assure that spring extension/ retraction is functioning properly.
-
Prior to assembly the actuator shaft should be fully retracted, except for spring extended models, and the grappling claw should be in the extended position.
-
2-½” & 3″ Valves use Adaptor Kit 0510390052. 4″ to 12″ valves use Adaptor Kit 0510390053, this kit includes leg extensions.
-
Remove the neck clamp mechanism by removing the two leg fasteners using 6mm Allen wrench. (Part #3)
-
Assemble the two leg extensions (Part #2) to the actuator legs (4″ to 12″ valves only.)
-
Reassemble the neck clamp to leg extensions by installing the two leg fasteners. (Part #3)
-
Using the 6mm Allen wrench, remove the threaded neck clamp (Part #4) of the actuator by removing the two neck clamp fasteners. (Part #5)
-
With the actuator oriented as shown, [Figure 8] actuator handle face on the same side as valve tag, assemble the actuator on to valve using the neck clamping mechanism. Assure that the neck clamp is seated properly into the valve neck groove.
-
First –> have to assemble coupler part # 9 to part #8
-
Take the anti-rotation arm (Part #6) open end and clasp the actuator legs (flat surface) and allow it to slide downwards.
-
Assemble the grappling device adapter (Part #9) to the valve stem with two split rings (Part #7) and split ring retainer. [Figure 6] (Part #9)
Note: The two split
rings fit into the split ring grove and the split ring retainer screws into
the grappling device adapter.
Note: For spring extended
actuators the shaft may need to be retracted, using the manual override, to a
position which allows for assembly.
-
Using the actuator manual override extend the actuator shaft and capture the grappling device adapter with the grappling device. (Part #10)
Note: For spring
extended actuators the grappling device adapter may be captured by the
grappling device during actuator assembly. -
Assure that the grappling claw is fully retracted into the grappling device.
GPM Settings:
-
Inspect the actuator for any sign of physical damage.
-
Refer to the Flow Rate Charts on page 6 or the flow rate calculator at https://braycommercialdivision.com product/simpleset-max-pressure-independentcontrol-valve/ for the dial setting that correlates to the specified
GPM. -
Turn the valve’s white dial located under stem [Figure 7] to desired setting.
-
Using 2.5mm Allen Wrench tighten the anti-rotation arm set screw around valve stem.
Overview
For Wiring and Operating Instructions for the GA(S) Actuators refer to:
https://braycommercialdivision.com/product/gasseries-globe-valve-actuators/
Simple Set Max – ANSI 125 Flow Rate Charts
| 2-1/2″ | 2-1/2″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-250-A-L-19| 0.6| 2.18| 4.4| 19
SSM-250-A-L-24| 0.8| 2.18| 5.6| 24
SSM-250-A-L-29| 1.0| 2.18| 6.6| 29
SSM-250-A-L-34| 1.2| 2.31| 7.7| 34
SSM-250-A-L-38| 1.4| 2.41| 8.6| 38
SSM-250-A-L-42| 1.6| 2.49| 9.6| 42
SSM-250-A-L-46| 1.8| 2.55| 10.5| 46
SSM-250-A-L-51| 2.0| 2.61| 11.5| 51
SSM-250-A-L-55| 2.2| 2.66| 12.5| 55
SSM-250-A-L-60| 2.4| 2.7| 13.5| 60
SSM-250-A-L-65| 2.6| 2.76| 14.7| 65
SSM-250-A-L-70| 2.8| 2.82| 15.8| 70
SSM-250-A-L-75| 3.0| 2.9| 17.1| 75
SSM-250-A-L-81| 3.2| 3| 18.5| 81
SSM-250-A-L-88| 3.4| 3.11| 19.9| 88
SSM-250-A-L-95| 3.6| 3.26| 21.5| 95
SSM-250-A-L-102| 3.8| 3.42| 23.2| 102
SSM-250-A-L-110| 4.0| 3.59| 25.0| 110
2-1/2″| 2-1/2″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-250-A-H-26| 0.6| 4.35| 6.0| 26
SSM-250-A-H-33| 0.8| 4.35| 7.6| 33
SSM-250-A-H-40| 1.0| 4.35| 9.1| 40
SSM-250-A-H-46| 1.2| 4.51| 10.5| 46
SSM-250-A-H-53| 1.4| 4.6| 11.9| 53
SSM-250-A-H-59| 1.6| 4.64| 13.3| 59
SSM-250-A-H-65| 1.8| 4.65| 14.7| 65
SSM-250-A-H-71| 2.0| 4.64| 16.0| 71
SSM-250-A-H-77| 2.2| 4.64| 17.5| 77
SSM-250-A-H-84| 2.4| 4.67| 19.0| 84
SSM-250-A-H-91| 2.6| 4.74| 20.6| 91
SSM-250-A-H-98| 2.8| 4.87| 22.3| 98
SSM-250-A-H-106| 3.0| 5.09| 24.1| 106
SSM-250-A-H-114| 3.2| 5.4| 26.0| 114
SSM-250-A-H-123| 3.4| 5.81| 28.0| 123
SSM-250-A-H-133| 3.6| 6.36| 30.2| 133
SSM-250-A-H-143| 3.8| 7.06| 32.5| 143
SSM-250-A-H-154| 4.0| 8.01| 35.0| 154
3″| 3″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-3-A-L-26| 0.6| 2.32| 5.3| 26
SSM-3-A-L-30| 0.8| 2.32| 6.9| 30
SSM-3-A-L-36| 1.0| 2.33| 8.3| 36
SSM-3-A-L-42| 1.2| 2.41| 9.6| 42
SSM-3-A-L-48| 1.4| 2.47| 10.9| 48
SSM-3-A-L-54| 1.6| 2.52| 12.2| 54
SSM-3-A-L-59| 1.8| 2.57| 13.5| 59
SSM-3-A-L-65| 2.0| 2.61| 14.8| 65
SSM-3-A-L-71| 2.2| 2.65| 16.2| 71
SSM-3-A-L-77| 2.4| 2.7| 17.6| 77
SSM-3-A-L-84| 2.6| 2.75| 19.1| 84
SSM-3-A-L-91| 2.8| 2.82| 20.7| 91
SSM-3-A-L-99| 3.0| 2.9| 22.4| 99
SSM-3-A-L-107| 3.2| 3| 24.3| 107
SSM-3-A-L-116| 3.4| 3.13| 26.4| 116
SSM-3-A-L-126| 3.6| 3.28| 28.7| 126
SSM-3-A-L-138| 3.8| 3.44| 31.2| 138
SSM-3-A-L-150| 4.0| 3.61| 34.0| 150
3″| 3″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-3-A-H-31| 0.6| 3.34| 7.0| 31
SSM-3-A-H-40| 0.8| 3.34| 9.0| 40
SSM-3-A-H-48| 1.0| 3.34| 11.0| 48
SSM-3-A-H-56| 1.2| 3.43| 12.8| 56
SSM-3-A-H-64| 1.4| 3.49| 14.5| 64
SSM-3-A-H-71| 1.6| 3.53| 16.2| 71
SSM-3-A-H-79| 1.8| 3.57| 18.0| 79
SSM-3-A-H-86| 2.0| 3.61| 19.6| 86
SSM-3-A-H-94| 2.2| 3.68| 21.4| 94
SSM-3-A-H-102| 2.4| 3.77| 23.2| 102
SSM-3-A-H-111| 2.6| 3.91| 25.1| 111
SSM-3-A-H-119| 2.8| 4.11| 27.1| 119
SSM-3-A-H-129| 3.0| 4.39| 29.3| 129
SSM-3-A-H-139| 3.2| 4.75| 31.6| 139
SSM-3-A-H-150| 3.4| 5.19| 34.1| 150
SSM-3-A-H-162| 3.6| 5.73| 36.8| 162
SSM-3-A-H-175| 3.8| 6.39| 39.8| 175
SSM-3-A-H-189| 4.0| 7.19| 43.0| 189
Note: Min. Delta P Available at Selected Flow Rate. See Website for Specific Flow Rate Settings Calculator
| 4″ | 4″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-4-A-L-53| 0.6| 2.75| 12.1| 53
SSM-4-A-L-67| 0.8| 2.83| 15.3| 67
SSM-4-A-L-80| 1.0| 2.9| 18.1| 80
SSM-4-A-L-91| 1.2| 2.96| 20.8| 91
SSM-4-A-L-102| 1.4| 3.02| 23.2| 102
SSM-4-A-L-112| 1.6| 3.08| 25.5| 112
SSM-4-A-L-122| 1.8| 3.13| 27.8| 122
SSM-4-A-L-132| 2.0| 3.19| 30.0| 132
SSM-4-A-L-143| 2.2| 3.25| 32.4| 143
SSM-4-A-L-154| 2.4| 3.32| 34.9| 154
SSM-4-A-L-166| 2.6| 3.4| 37.6| 166
SSM-4-A-L-179| 2.8| 3.5| 40.6| 179
SSM-4-A-L-194| 3.0| 3.63| 44.0| 194
SSM-4-A-L-210| 3.2| 3.78| 47.7| 210
SSM-4-A-L-229| 3.4| 3.98| 51.9| 229
SSM-4-A-L-249| 3.6| 4.25| 56.7| 249
SSM-4-A-L-273| 3.8| 4.6| 62.0| 273
SSM-4-A-L-299| 4.0| 5.08| 68.0| 299
4″| 4″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-4-A-H-65| 0.6| 4.14| 14.8| 65
SSM-4-A-H-83| 0.8| 4.24| 18.9| 83
SSM-4-A-H-99| 1.0| 4.35| 22.6| 99
SSM-4-A-H-114| 1.2| 4.48| 26.0| 114
SSM-4-A-H-128| 1.4| 4.61| 29.1| 128
SSM-4-A-H-141| 1.6| 4.75| 32.1| 141
SSM-4-A-H-154| 1.8| 4.91| 35.1| 154
SSM-4-A-H-168| 2.0| 5.08| 38.1| 168
SSM-4-A-H-181| 2.2| 5.27| 41.2| 181
SSM-4-A-H-196| 2.4| 5.5| 44.5| 196
SSM-4-A-H-212| 2.6| 5.78| 48.2| 212
SSM-4-A-H-230| 2.8| 6.11| 52.2| 230
SSM-4-A-H-250| 3.0| 6.52| 56.7| 250
SSM-4-A-H-272| 3.2| 7.05| 61.9| 272
SSM-4-A-H-298| 3.4| 7.7| 67.7| 298
SSM-4-A-H-327| 3.6| 8.51| 74.2| 327
SSM-4-A-H-360| 3.8| 9.56| 81.7| 360
SSM-4-A-H-396| 4.0| 10.87| 90.0| 396
5″| 5″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-5-A-L-81| 0.6| 2.32| 18.5| 81
SSM-5-A-L-104| 0.8| 2.32| 23.6| 104
SSM-5-A-L-125| 1.0| 2.32| 28.5| 125
SSM-5-A-L-147| 1.2| 2.39| 33.3| 147
SSM-5-A-L-167| 1.4| 2.46| 38.0| 167
SSM-5-A-L-188| 1.6| 2.51| 42.6| 188
SSM-5-A-L-207| 1.8| 2.56| 47.1| 207
SSM-5-A-L-227| 2.0| 2.61| 51.5| 227
SSM-5-A-L-246| 2.2| 2.67| 55.9| 246
SSM-5-A-L-266| 2.4| 2.73| 60.4| 266
SSM-5-A-L-286| 2.6| 2.81| 65.0| 286
SSM-5-A-L-308| 2.8| 2.91| 69.8| 308
SSM-5-A-L-330| 3.0| 3.05| 75.0| 330
SSM-5-A-L-355| 3.2| 3.23| 80.6| 355
SSM-5-A-L-382| 3.4| 3.48| 86.7| 382
SSM-5-A-L-412| 3.6| 3.83| 93.6| 412
SSM-5-A-L-446| 3.8| 4.34| 101.3| 446
SSM-5-A-L-484| 4.0| 5.08| 110.0| 484
5″| 5″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-5-A-H-101| 0.6| 3.92| 23.0| 101
SSM-5-A-H-132| 0.8| 3.92| 29.9| 131
SSM-5-A-H-161| 1.0| 3.92| 36.5| 161
SSM-5-A-H-188| 1.2| 3.99| 42.8| 188
SSM-5-A-H-215| 1.4| 4.05| 48.7| 215
SSM-5-A-H-240| 1.6| 4.1| 54.5| 240
SSM-5-A-H-264| 1.8| 4.15| 60.0| 264
SSM-5-A-H-288| 2.0| 4.21| 65.5| 288
SSM-5-A-H-312| 2.2| 4.27| 70.9| 312
SSM-5-A-H-336| 2.4| 4.35| 76.4| 336
SSM-5-A-H-361| 2.6| 4.46| 82.0| 361
SSM-5-A-H-387| 2.8| 4.6| 87.8| 387
SSM-5-A-H-414| 3.0| 7.79| 94.0| 414
SSM-5-A-H-443| 3.2| 5.05| 100.7| 443
SSM-5-A-H-475| 3.4| 5.41| 108.0| 475
SSM-5-A-H-511| 3.6| 5.92| 116.0| 511
SSM-5-A-H-550| 3.8| 6.65| 125.0| 550
SSM-5-A-H-594| 4.0| 7.69| 135.0| 594
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specific Flow Rate Settings Calculator
| 6″ | 6″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-6-A-L-113| 0.6| 3.05| 25.6| 113
SSM-6-A-L-143| 0.8| 3.05| 32.6| 143
SSM-6-A-L-173| 1.0| 3.05| 39.2| 173
SSM-6-A-L-201| 1.2| 3.05| 45.6| 201
SSM-6-A-L-228| 1.4| 3.05| 51.8| 228
SSM-6-A-L-255| 1.6| 3.05| 58.0| 255
SSM-6-A-L-282| 1.8| 3.05| 64.1| 282
SSM-6-A-L-310| 2.0| 3.19| 70.4| 310
SSM-6-A-L-338| 2.2| 3.39| 76.8| 338
SSM-6-A-L-367| 2.4| 3.61| 83.4| 367
SSM-6-A-L-398| 2.6| 3.86| 90.3| 398
SSM-6-A-L-429| 2.8| 4.11| 97.5| 429
SSM-6-A-L-462| 3.0| 4.35| 105.0| 462
SSM-6-A-L-497| 3.2| 4.58| 112.9| 497
SSM-6-A-L-533| 3.4| 4.77| 121.1| 533
SSM-6-A-L-571| 3.6| 4.93| 129.7| 571
SSM-6-A-L-610| 3.8| 5.03| 138.7| 610
SSM-6-A-L-652| 4.0| 5.08| 148.0| 652
6″| 6″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-6-A-H-141| 0.6| 4.79| 32.0| 141
SSM-6-A-H-182| 0.8| 4.79| 41.3| 182
SSM-6-A-H-220| 1.0| 4.79| 50.0| 220
SSM-6-A-H-256| 1.2| 4.79| 58.2| 256
SSM-6-A-H-291| 1.4| 4.79| 66.0| 291
SSM-6-A-H-324| 1.6| 4.79| 73.7| 324
SSM-6-A-H-358| 1.8| 4.79| 81.3| 358
SSM-6-A-H-392| 2.0| 4.93| 89.0| 392
SSM-6-A-H-427| 2.2| 5.16| 96.9| 427
SSM-6-A-H-463| 2.4| 5.46| 105.2| 4637
SSM-6-A-H-501| 2.6| 5.82| 113.9| 5017
SSM-6-A-H-542| 2.8| 6.23| 123.1| 5427
SSM-6-A-H-586| 3.0| 6.68| 133.0| 586
SSM-6-A-H-632| 3.2| 7.14| 143.6| 632
SSM-6-A-H-683| 3.4| 7.69| 155.1| 683
SSM-6-A-H-737| 3.6| 8.23| 167.4| 737
SSM-6-A-H-796| 3.8| 8.81| 180.7| 796
SSM-6-A-H-859| 4.0| 9.44| 195.0| 859
8″| 8″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-8-A-L-418| 1| 1.6| 95.2| 418
SSM-8-A-L-435| 1.2| 1.7| 98.8| 435
SSM-8-A-L-460| 1.4| 1.8| 104.5| 460
SSM-8-A-L-485| 1.6| 1.9| 110.2| 485
SSM-8-A-L-515| 1.8| 2.1| 117.0| 515
SSM-8-A-L-545| 2| 2.3| 123.8| 545
SSM-8-A-L-575| 2.2| 2.5| 130.6| 575
SSM-8-A-L-610| 2.4| 2.7| 138.6| 610
SSM-8-A-L-640| 2.6| 2.9| 145.4| 640
SSM-8-A-L-680| 2.8| 3.2| 154.4| 680
SSM-8-A-L-720| 3| 3.4| 163.5| 720
SSM-8-A-L-760| 3.2| 3.7| 172.6| 760
SSM-8-A-L-795| 3.4| 3.9| 180.6| 795
SSM-8-A-L-835| 3.6| 4.2| 189.7| 835
SSM-8 -A-L-875| 3.8| 4.4| 198.7| 875
SSM-8-A-L-925| 4| 4.6| 209.9| 925
8″| 8″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-8-A-H-572| 1| 4.5| 130.1| 572
SSM-8-A-H-598| 1.2| 5| 135.8| 598
SSM-8-A-H-630| 1.4| 5| 143.1| 630
SSM-8-A-H-664| 1.6| 5| 150.8| 664
SSM-8-A-H-702| 1.8| 5| 159.4| 702
SSM-8-A-H-739| 2| 6| 167.9| 739
SSM-8-A-H-779| 2.2| 6| 176.9| 779
SSM-8-A-H-823| 2.4| 7| 186.9| 823
SSM-8-A-H-865| 2.6| 7| 196.5| 865
SSM-8-A-H-910| 2.8| 8| 206.7| 910
SSM-8-A-H-957| 3| 9| 217.4| 957
SSM-8-A-H-1008| 3.2| 9| 228.9| 1008
SSM-8-A-H-1058| 3.4| 10| 240.3| 1058
SSM-8-A-H-1109| 3.6| 10| 251.9| 1109
SSM-8-A-H-1164| 3.8| 11| 264.4| 1164
SSM-8-A-H-1233| 4| 11| 279.8| 1233
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specific Flow Rate Settings Calculator.
| 10″ | 10″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-10-A-L-837| 1| 1.5| 190.1| 837
SSM-10-A-L-900| 1.2| 1.5| 204.4| 900
SSM-10-A-L-960| 1.4| 1.6| 218.0| 960
SSM-10-A-L-1020| 1.6| 1.7| 231.7| 1020
SSM-10-A-L-1075| 1.8| 1.9| 244.2| 1075
SSM-10-A-L-1135| 2| 2.1| 257.8| 1135
SSM-10-A-L-1195| 2.2| 2.4| 271.4| 1195
SSM-10-A-L-1255| 2.4| 2.6| 285.0| 1255
SSM-10-A-L-1325| 2.6| 2.9| 300.9| 1325
SSM-10-A-L-1400| 2.8| 3.3| 318.0| 1400
SSM-10-A-L-1480| 3| 3.6| 336.1| 1480
SSM-10-A-L-1570| 3.2| 3.9| 356.6| 1570
SSM-10-A-L-1680| 3.4| 3.4| 381.6| 1680
SSM-10-A-L-1795| 3.6| 4.5| 407.7| 1795
SSM-10-A-L-1930| 3.8| 4.8| 438.4| 1930
SSM-10-A-L-2091| 4| 5.1| 474.9| 2091
10″| 10″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-10-A-H-1079| 1| 2.18| 245.1| 1079
SSM-10-A-H-1118| 1.2| 2.3| 253.9| 1118
SSM-10-A-H-1178| 1.4| 2.5| 267.6| 1178
SSM-10-A-H-1246| 1.6| 2.8| 283.0| 1246
SSM-10-A-H-1330| 1.8| 3.1| 302.1| 1330
SSM-10-A-H-1420| 2| 3.6| 322.5| 1420
SSM-10-A-H-1515| 2.2| 4.1| 344.1| 1515
SSM-10-A-H-1620| 2.4| 4.6| 367.9| 1620
SSM-10-A-H-1730| 2.6| 5.2| 392.9| 1730
SSM-10-A-H-1845| 2.8| 5.8| 419.1| 1845
SSM-10-A-H-1965| 3| 6.4| 446.3| 1965
SSM-10-A-H-2090| 3.2| 7.1| 474.7| 2090
SSM-10-A-H-2220| 3.4| 7.8| 504.2| 2220
SSM-10-A-H-2355| 3.6| 8.6| 534.9| 2355
SSM-10-A-H-2490| 3.8| 9.3| 565.5| 2490
SSM-10-A-H-2642| 4| 10.2| 599.8| 2642
12″| 12″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-12-A-L-837| 1| 1.5| 190.1| 837
SSM-12-A-L-895| 1.2| 1.5| 203.3| 895
SSM-12-A-L-955| 1.4| 1.6| 216.9| 955
SSM-12-A-L-1015| 1.6| 1.7| 230.5| 1015
SSM-12-A-L-1075| 1.8| 1.8| 244.2| 1075
SSM-12-A-L-1130| 2| 2.1| 256.7| 1130
SSM-12-A-L-1195| 2.2| 2.4| 271.4| 1195
SSM-12-A-L-1255| 2.4| 2.6| 285.0| 1255
SSM-12-A-L-1325| 2.6| 2.9| 300.9| 1325
SSM-12-A-L-1400| 2.8| 3.3| 318.0| 1400
SSM-12-A-L-1480| 3| 3.6| 336.1| 1480
SSM-12-A-L-1570| 3.2| 3.2| 356.6| 1570
SSM-12-A-L-1680| 3.4| 4.2| 381.6| 1680
SSM-12-A-L-1795| 3.6| 4.5| 407.7| 1795
SSM-12-A-L-1930| 3.8| 4.8| 438.4| 1930
SSM-12-A-L-2091| 4| 5.1| 474.9| 2091
12″| 12″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-12-A-H-1079| 1| 2.2| 245.1| 1079
SSM-12-A-H-1118| 1.2| 2.3| 253.9| 1118
SSM-12-A-H-1178| 1.4| 2.5| 267.6| 1178
SSM-12-A-H-1248| 1.6| 2.8| 283.5| 1248
SSM-12-A-H-1330| 1.8| 3.1| 302.1| 1330
SSM-12-A-H-1418| 2| 3.6| 322.1| 1418
SSM-12-A-H-1515| 2.2| 4.1| 344.1| 1515
SSM-12-A-H-1618| 2.4| 4.6| 367.5| 1618
SSM-12-A-H-1730| 2.6| 5.2| 392.9| 1730
SSM-12-A-H-1847| 2.8| 5.8| 419.5| 1847
SSM-12-A-H-1969| 3| 6.5| 447.2| 1969
SSM-12-A-H-2090| 3.2| 7.1| 474.7| 2090
SSM-12-A-H-2225| 3.4| 7.9| 505.4| 2225
SSM-12-A-H-2350| 3.6| 8.6| 533.7| 2350
SSM-12-A-H-2490| 3.8| 9.3| 565.5| 2490
SSM-12-A-H-2642| 4| 10.2| 599.8| 2642
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specific Flow Rate Settings Calculator
Simple Set Max – ANSI 250 Flow Rate Charts
| 2-1/2″ | 2-1/2″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-250-A250-L-19| 0.6| 2.18| 4.4| 19
SSM-250-A250-L-24| 0.8| 2.18| 5.6| 24
SSM-250-A250-L-29| 1.0| 2.18| 6.6| 29
SSM-250-A250-L-34| 1.2| 2.31| 7.7| 34
SSM-250-A250-L-38| 1.4| 2.41| 8.6| 38
SSM-250-A250-L-42| 1.6| 2.49| 9.6| 42
SSM-250-A250-L-46| 1.8| 2.55| 10.5| 46
SSM-250-A250-L-51| 2.0| 2.61| 11.5| 51
SSM-250-A250-L-55| 2.2| 2.66| 12.5| 55
SSM-250-A250-L-60| 2.4| 2.7| 13.5| 60
SSM-250-A250-L-65| 2.6| 2.76| 14.7| 65
SSM-250-A250-L-70| 2.8| 2.82| 15.8| 70
SSM-250-A250-L-75| 3.0| 2.9| 17.1| 75
SSM-250-A250-L-81| 3.2| 3| 18.5| 81
SSM-250-A250-L-88| 3.4| 3.11| 19.9| 88
SSM-250-A250-L-95| 3.6| 3.26| 21.5| 95
SSM-250-A250-L-102| 3.8| 3.42| 23.2| 102
SSM-250-A250-L-110| 4.0| 3.59| 25.0| 110
2-1/2″| 2-1/2″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-250-A250-H-26| 0.6| 4.35| 6.0| 26
SSM-250-A250-H-33| 0.8| 4.35| 7.6| 33
SSM-250-A250-H-40| 1.0| 4.35| 9.1| 40
SSM-250-A250-H-46| 1.2| 4.51| 10.5| 46
SSM-250-A250-H-53| 1.4| 4.6| 11.9| 53
SSM-250-A250-H-59| 1.6| 4.64| 13.3| 59
SSM-250-A250-H-65| 1.8| 4.65| 14.7| 65
SSM-250-A250-H-71| 2.0| 4.64| 16.0| 71
SSM-250-A250-H-77| 2.2| 4.64| 17.5| 77
SSM-250-A250-H-84| 2.4| 4.67| 19.0| 84
SSM-250-A250-H-91| 2.6| 4.74| 20.6| 91
SSM-250-A250-H-98| 2.8| 4.87| 22.3| 98
SSM-250-A250-H-106| 3.0| 5.09| 24.1| 106
SSM-250-A250-H-114| 3.2| 5.4| 26.0| 114
SSM-250-A250-H-123| 3.4| 5.81| 28.0| 123
SSM-250-A250-H-133| 3.6| 6.36| 30.2| 133
SSM-250-A250-H-143| 3.8| 7.06| 32.5| 143
SSM-250-A250-H-154| 4.0| 8.01| 35.0| 154
3″| 3″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-3-A250-L-26| 0.6| 2.32| 5.3| 26
SSM-3-A250-L-30| 0.8| 2.32| 6.9| 30
SSM-3-A250-L-36| 1.0| 2.33| 8.3| 36
SSM-3-A250-L-42| 1.2| 2.41| 9.6| 42
SSM-3-A250-L-48| 1.4| 2.47| 10.9| 48
SSM-3-A250-L-54| 1.6| 2.52| 12.2| 54
SSM-3-A250-L-59| 1.8| 2.57| 13.5| 59
SSM-3-A250-L-65| 2.0| 2.61| 14.8| 65
SSM-3-A250-L-71| 2.2| 2.65| 16.2| 71
SSM-3-A250-L-77| 2.4| 2.7| 17.6| 77
SSM-3-A250-L-84| 2.6| 2.75| 19.1| 84
SSM-3-A250-L-91| 2.8| 2.82| 20.7| 91
SSM-3-A250-L-99| 3.0| 2.9| 22.4| 99
SSM-3-A250-L-107| 3.2| 3| 24.3| 107
SSM-3-A250-L-116| 3.4| 3.13| 26.4| 116
SSM-3-A250-L-126| 3.6| 3.28| 28.7| 126
SSM-3-A250-L-138| 3.8| 3.44| 31.2| 138
SSM-3-A250-L-150| 4.0| 3.61| 34.0| 150
3″| 3″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-3-A250-H-31| 0.6| 3.34| 7.0| 31
SSM-3-A250-H-40| 0.8| 3.34| 9.0| 40
SSM-3-A250-H-48| 1.0| 3.34| 11.0| 48
SSM-3-A250-H-56| 1.2| 3.43| 12.8| 56
SSM-3-A250-H-64| 1.4| 3.49| 14.5| 64
SSM-3-A250-H-71| 1.6| 3.53| 16.2| 71
SSM-3-A250-H-79| 1.8| 3.57| 18.0| 79
SSM-3-A250-H-86| 2.0| 3.61| 19.6| 86
SSM-3-A250-H-94| 2.2| 3.68| 21.4| 94
SSM-3-A250-H-102| 2.4| 3.77| 23.2| 102
SSM-3-A250-H-111| 2.6| 3.91| 25.1| 111
SSM-3-A250-H-119| 2.8| 4.11| 27.1| 119
SSM-3-A250-H-129| 3.0| 4.39| 29.3| 129
SSM-3-A250-H-139| 3.2| 4.75| 31.6| 139
SSM-3-A250-H-150| 3.4| 5.19| 34.1| 150
SSM-3-A250-H-162| 3.6| 5.73| 36.8| 162
SSM-3-A250-H-175| 3.8| 6.39| 39.8| 175
SSM-3-A250-H-189| 4.0| 7.19| 43.0| 189
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specifc Flow Rate Settings Calculator
| 4″ | 4″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-4-A250-L-53| 0.6| 2.75| 12.1| 53
SSM-4-A250-L-67| 0.8| 2.83| 15.3| 67
SSM-4-A250-L-80| 1.0| 2.9| 18.1| 80
SSM-4-A250-L-91| 1.2| 2.96| 20.8| 91
SSM-4-A250-L-102| 1.4| 3.02| 23.2| 102
SSM-4-A250-L-112| 1.6| 3.08| 25.5| 112
SSM-4-A250-L-122| 1.8| 3.13| 27.8| 122
SSM-4-A250-L-132| 2.0| 3.19| 30.0| 132
SSM-4-A250-L-143| 2.2| 3.25| 32.4| 143
SSM-4-A250-L-154| 2.4| 3.32| 34.9| 154
SSM-4-A250-L-166| 2.6| 3.4| 37.6| 166
SSM-4-A250-L-179| 2.8| 3.5| 40.6| 179
SSM-4-A250-L-194| 3.0| 3.63| 44.0| 194
SSM-4-A250-L-210| 3.2| 3.78| 47.7| 210
SSM-4-A250-L-229| 3.4| 3.98| 51.9| 229
SSM-4-A250-L-249| 3.6| 4.25| 56.7| 249
SSM-4-A250-L-273| 3.8| 4.6| 62.0| 273
SSM-4-A250-L-299| 4.0| 5.08| 68.0| 299
4″| 4″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-4-A250-H-65| 0.6| 4.14| 14.8| 65
SSM-4-A250-H-83| 0.8| 4.24| 18.9| 83
SSM-4-A250-H-99| 1.0| 4.35| 22.6| 99.
SSM-4-A250-H-114| 1.2| 4.48| 26.0| 114
SSM-4-A250-H-128| 1.4| 4.61| 29.1| 128
SSM-4-A250-H-141| 1.6| 4.75| 32.1| 141
SSM-4-A250-H-154| 1.8| 4.91| 35.1| 154
SSM-4-A250-H-168| 2.0| 5.08| 38.1| 168
SSM-4-A250-H-181| 2.2| 5.27| 41.2| 181
SSM-4-A250-H-196| 2.4| 5.5| 44.5| 196
SSM-4-A250-H-212| 2.6| 5.78| 48.2| 212
SSM-4-A250-H-230| 2.8| 6.11| 52.2| 230
SSM-4-A250-H-250| 3.0| 6.52| 56.7| 250
SSM-4-A250-H-272| 3.2| 7.05| 61.9| 272
SSM-4-A250-H-298| 3.4| 7.7| 67.7| 298
SSM-4-A250-H-327| 3.6| 8.51| 74.2| 327
SSM-4-A250-H-360| 3.8| 9.56| 81.7| 360
SSM-4-A250-H-396| 4.0| 10.87| 90.0| 396
5″| 5″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-5-A250-L-81| 0.6| 2.32| 18.5| 81
SSM-5-A250-L-104| 0.8| 2.32| 23.6| 104
SSM-5-A250-L-125| 1.0| 2.32| 28.5| 125
SSM-5-A250-L-147| 1.2| 2.39| 33.3| 147
SSM-5-A250-L-167| 1.4| 2.46| 38.0| 167
SSM-5-A250-L-188| 1.6| 2.51| 42.6| 188
SSM-5-A250-L-207| 1.8| 2.56| 47.1| 207
SSM-5-A250-L-227| 2.0| 2.61| 51.5| 227
SSM-5-A250-L-246| 2.2| 2.67| 55.9| 246
SSM-5-A250-L-266| 2.4| 2.73| 60.4| 266
SSM-5-A250-L-286| 2.6| 2.81| 65.0| 286
SSM-5-A250-L-308| 2.8| 2.91| 69.8| 308
SSM-5-A250-L-330| 3.0| 3.05| 75.0| 330
SSM-5-A250-L-355| 3.2| 3.23| 80.6| 355
SSM-5-A250-L-382| 3.4| 3.48| 86.7| 382
SSM-5-A250-L-412| 3.6| 3.83| 93.6| 412
SSM-5-A250-L-446| 3.8| 4.34| 101.3| 446
SSM-5-A250-L-484| 4.0| 5.08| 110.0| 484
5″| 5″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-5-A250-H-101| 0.6| 3.92| 23.0| 101
SSM-5-A250-H-132| 0.8| 3.92| 29.9| 132
SSM-5-A250-H-161| 1.0| 3.92| 36.5| 161
SSM-5-A250-H-188| 1.2| 3.99| 42.8| 188
SSM-5-A250-H-215| 1.4| 4.05| 48.7| 215
SSM-5-A250-H-240| 1.6| 4.1| 54.5| 240
SSM-5-A250-H-264| 1.8| 4.15| 60.0| 264
SSM-5-A250-H-288| 2.0| 4.21| 65.5| 288
SSM-5-A250-H-312| 2.2| 4.27| 70.9| 312
SSM-5-A250-H-336| 2.4| 4.35| 76.4| 336
SSM-5-A250-H-361| 2.6| 4.46| 82.0| 361
SSM-5-A250-H-387| 2.8| 4.6| 87.8| 387
SSM-5-A250-H-414| 3.0| 7.79| 94.0| 414
SSM-5-A250-H-443| 3.2| 5.05| 100.7| 443
SSM-5-A250-H-475| 3.4| 5.41| 108.0| 475
SSM-5-A250-H-511| 3.6| 5.92| 116.0| 511
SSM-5-A250-H-550| 3.8| 6.65| 125.0| 550
SSM-5-A250-H-594| 4.0| 7.69| 135.0| 594
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specific Flow Rate Settings Calculator
| 6″ | 6″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-6-A250-L-113| 0.6| 3.05| 25.6| 113
SSM-6-A250-L-143| 0.8| 3.05| 32.6| 143
SSM-6-A250-L-173| 1.0| 3.05| 39.2| 173
SSM-6-A250-L-201| 1.2| 3.05| 45.6| 201
SSM-6-A250-L-228| 1.4| 3.05| 51.8| 228
SSM-6-A250-L-255| 1.6| 3.05| 58.0| 255
SSM-6-A250-L-282| 1.8| 3.05| 64.1| 282
SSM-6-A250-L-310| 2.0| 3.19| 70.4| 310
SSM-6-A250-L-338| 2.2| 3.39| 76.8| 338
SSM-6-A250-L-367| 2.4| 3.61| 83.4| 367
SSM-6-A250-L-398| 2.6| 3.86| 90.3| 398
SSM-6-A250-L-429| 2.8| 4.11| 97.5| 429
SSM-6-A250-L-462| 3.0| 4.35| 105.0| 462
SSM-6-A250-L-497| 3.2| 4.58| 112.9| 497
SSM-6-A250-L-533| 3.4| 4.77| 121.1| 533
SSM-6-A250-L-571| 3.6| 4.93| 129.7| 571
SSM-6-A250-L-610| 3.8| 5.03| 138.7| 610
SSM-6-A250-L-652| 4.0| 5.08| 148.0| 652
6″| 6″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-6-A250-H-141| 0.6| 4.79| 32.0| 141
SSM-6-A250-H-182| 0.8| 4.79| 41.3| 182
SSM-6-A250-H-220| 1.0| 4.79| 50.0| 220
SSM-6-A250-H-256| 1.2| 4.79| 58.2| 256
SSM-6-A250-H-291| 1.4| 4.79| 66.0| 291
SSM-6-A250-H-324| 1.6| 4.79| 73.7| 324
SSM-6-A250-H-358| 1.8| 4.79| 81.3| 358
SSM-6-A250-H-392| 2.0| 4.93| 89.0| 392
SSM-6-A250-H-427| 2.2| 5.16| 96.9| 427
SSM-6-A250-H-463| 2.4| 5.46| 105.2| 463
SSM-6-A250-H-501| 2.6| 5.82| 113.9| 501
SSM-6-A250-H-542| 2.8| 6.23| 123.1| 542
SSM-6-A250-H-586| 3.0| 6.68| 133.0| 586
SSM-6-A250-H-632| 3.2| 7.14| 143.6| 632
SSM-6-A250-H-683| 3.4| 7.69| 155.1| 683
SSM-6-A250-H-737| 3.6| 8.23| 167.4| 737
SSM-6-A250-H-796| 3.8| 8.81| 180.7| 796
SSM-6-A250-H-859| 4.0| 9.44| 195.0| 859
8″| 8″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-8-A250-L-418| 1| 1.6| 95.2| 418
SSM-8-A250-L-435| 1.2| 1.7| 98.8| 435
SSM-8-A250-L-460| 1.4| 1.8| 104.5| 460
SSM-8-A250-L-485| 1.6| 1.9| 110.2| 485
SSM-8-A250-L-515| 1.8| 2.1| 117.0| 515
SSM-8-A250-L-545| 2| 2.3| 123.8| 545
SSM-8-A250-L-575| 2.2| 2.5| 130.6| 575
SSM-8-A250-L-610| 2.4| 2.7| 138.6| 610
SSM-8-A250-L-640| 2.6| 2.9| 145.4| 640
SSM-8-A250-L-680| 2.8| 3.2| 154.4| 680
SSM-8-A250-L-720| 3| 3.4| 163.5| 720
SSM-8-A250-L-760| 3.2| 3.7| 172.6| 760
SSM-8-A250-L-795| 3.4| 3.9| 180.6| 795
SSM-8-A250-L-835| 3.6| 4.2| 189.7| 835
SSM-8 -A250-L-875| 3.8| 4.4| 198.7| 875
SSM-8-A250-L-925| 4| 4.6| 209.9| 925
8″| 8″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-8-A250-H-572| 1| 4.5| 130.1| 572
SSM-8-A250-H-598| 1.2| 5| 135.8| 598
SSM-8-A250-H-630| 1.4| 5| 143.1| 630
SSM-8-A250-H-664| 1.6| 5| 150.8| 664
SSM-8-A250-H-702| 1.8| 5| 159.4| 702
SSM-8-A250-H-739| 2| 6| 167.9| 739
SSM-8-A250-H-779| 2.2| 6| 176.9| 779
SSM-8-A250-H-823| 2.4| 7| 186.9| 823
SSM-8-A250-H-865| 2.6| 7| 196.5| 865
SSM-8-A250-H-910| 2.8| 8| 206.7| 910
SSM-8-A250-H-957| 3| 9| 217.4| 957
SSM-8-A250-H-1008| 3.2| 9| 228.9| 1008
SSM-8-A250-H-1058| 3.4| 10| 240.3| 1058
SSM-8-A250-H-1109| 3.6| 10| 251.9| 1109
SSM-8-A250-H-1164| 3.8| 11| 264.4| 1164
SSM-8-A250-H-1233| 4| 11| 279.8| 1233
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specifc Flow Rate Settings Calculator
| 10″ | 10″ Low Flow Rate Cartridge |
|---|---|
| Model Number | Pre-Set |
GPM
SSM-10-A250-L-837| 1| 1.5| 190.1| 837
SSM-10-A250-L-900| 1.2| 1.5| 204.4| 900
SSM-10-A250-L-960| 1.4| 1.6| 218.0| 960
SSM-10-A250-L-1020| 1.6| 1.7| 231.7| 1020
SSM-10-A250-L-1075| 1.8| 1.9| 244.2| 1075
SSM-10-A250-L-1135| 2| 2.1| 257.8| 1135
SSM-10-A250-L-1195| 2.2| 2.4| 271.4| 1195
SSM-10-A250-L-1255| 2.4| 2.6| 285.0| 1255
SSM-10-A250-L-1325| 2.6| 2.9| 300.9| 1325
SSM-10-A250-L-1400| 2.8| 3.3| 318.0| 1400
SSM-10-A250-L-1480| 3| 3.6| 336.1| 1480
SSM-10-A250-L-1570| 3.2| 3.9| 356.6| 1570
SSM-10-A250-L-1680| 3.4| 3.4| 381.6| 1680
SSM-10-A250-L-1795| 3.6| 4.5| 407.7| 1795
SSM-10-A250-L-1930| 3.8| 4.8| 438.4| 1930
SSM-10-A250-L-2091| 4| 5.1| 474.9| 2091
10″| 10″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-10-A250-H-1079| 1| 2.18| 245.1| 1079
SSM-10-A250-H-1118| 1.2| 2.3| 253.9| 1118
SSM-10-A250-H-1178| 1.4| 2.5| 267.6| 1178
SSM-10-A250-H-1246| 1.6| 2.8| 283.0| 1246
SSM-10-A250-H-1330| 1.8| 3.1| 302.1| 1330
SSM-10-A250-H-1420| 2| 3.6| 322.5| 1420
SSM-10-A250-H-1515| 2.2| 4.1| 344.1| 1515
SSM-10-A250-H-1620| 2.4| 4.6| 367.9| 1620
SSM-10-A250-H-1730| 2.6| 5.2| 392.9| 1730
SSM-10-A250-H-1845| 2.8| 5.8| 419.1| 1845
SSM-10-A250-H-1965| 3| 6.4| 446.3| 1965
SSM-10-A250-H-2090| 3.2| 7.1| 474.7| 2090
SSM-10-A250-H-2220| 3.4| 7.8| 504.2| 2220
SSM-10-A250-H-2355| 3.6| 8.6| 534.9| 2355
SSM-10-A250-H-2490| 3.8| 9.3| 565.5| 2490
SSM-10-A250-H-2642| 4| 10.2| 599.8| 2642
12″| 12″ Low Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM
SSM-12-A250-L-837| 1| 1.5| 190.1| 837
SSM-12-A250-L-895| 1.2| 1.5| 203.3| 895
SSM-12-A250-L-955| 1.4| 1.6| 216.9| 955
SSM-12-A250-L-1015| 1.6| 1.7| 230.5| 1015
SSM-12-A250-L-1075| 1.8| 1.8| 244.2| 1075
SSM-12-A250-L-1130| 2| 2.1| 256.7| 1130
SSM-12-A250-L-1195| 2.2| 2.4| 271.4| 1195
SSM-12-A250-L-1255| 2.4| 2.6| 285.0| 1255
SSM-12-A250-L-1325| 2.6| 2.9| 300.9| 1325
SSM-12-A250-L-1400| 2.8| 3.3| 318.0| 1400
SSM-12-A250-L-1480| 3| 3.6| 336.1| 1480
SSM-12-A250-L-1570| 3.2| 3.2| 356.6| 1570
SSM-12-A250-L-1680| 3.4| 4.2| 381.6| 1680
SSM-12-A250-L-1795| 3.6| 4.5| 407.7| 1795
SSM-12-A250-L-1930| 3.8| 4.8| 438.4| 1930
SSM-12-A250-L-2091| 4| 5.1| 474.9| 2091
12″| 12″ High Flow Rate Cartridge
---|---
Model Number| Pre-Set| Min. Delta P| Flow m3/h| Flow
GPM**
SSM-12-A250-H-1079| 1| 2.2| 245.1| 1079
SSM-12-A250-H-1118| 1.2| 2.3| 253.9| 1118
SSM-12-A250-H-1178| 1.4| 2.5| 267.6| 1178
SSM-12-A250-H-1248| 1.6| 2.8| 283.5| 1248
SSM-12-A250-H-1330| 1.8| 3.1| 302.1| 1330
SSM-12-A250-H-1418| 2| 3.6| 322.1| 1418
SSM-12-A250-H-1515| 2.2| 4.1| 344.1| 1515
SSM-12-A250-H-1618| 2.4| 4.6| 367.5| 1618
SSM-12-A250-H-1730| 2.6| 5.2| 392.9| 1730
SSM-12-A250-H-1847| 2.8| 5.8| 419.5| 1847
SSM-12-A250-H-1969| 3| 6.5| 447.2| 1969
SSM-12-A250-H-2090| 3.2| 7.1| 474.7| 2090
SSM-12-A250-H-2225| 3.4| 7.9| 505.4| 2225
SSM-12-A250-H-2350| 3.6| 8.6| 533.7| 2350
SSM-12-A250-H-2490| 3.8| 9.3| 565.5| 2490
SSM-12-A250-H-2642| 4| 10.2| 599.8| 2642
Note: Min. Delta P Available at Selected Flow Rate.
See Website for Specifc Flow Rate Settings Calculator
Simple Set Max – ANSI 125 Dimensions – 2-1/2″ – 12″
Simple Set Max ANSI 125 Dimensions with GA(S) Actuators — 2-1/2″ – 12″
ANSI 125 Model #| Connection| Flow Range| Please Reference the Illustration
L| H| H1| D| W| Weight
x = Flow in GPM| in.| mm| GPM| in.| mm| in.| mm| in.| mm| in.| mm| in.| mm|
lbs| kg
SSM-250-A-L-x| 2.5| 65| 19 – 110| 10.87| 276| 3.51| 89| 19.12| 486| 7.01| 178|
6.41| 163| 41| 19
SSM-250-A-H-x| 2.5| 65| 26 – 154| 10.87| 276| 3.51| 89| 19.12| 486| 7.01| 178|
6.41| 163| 41| 19
SSM-3-A-L-x| 3.0| 80| 26 – 150| 11.73| 298| 3.75| 95| 19.98| 507| 7.52| 191|
7.96| 202| 61| 28
SSM-3-A-H-x| 3.0| 80| 31 – 189| 11.73| 298| 3.75| 95| 19.98| 507| 7.52| 191|
7.96| 202| 61| 28
SSM-4-A-L-x| 4.0| 100| 53 – 299| 13.86| 352| 4.51| 115| 24.52| 623| 9.02| 229|
10.53| 267| 123| 56
SSM-4-A-H-x| 4.0| 100| 65 – 396| 13.86| 352| 4.51| 115| 24.52| 623| 9.02| 229|
10.53| 267| 123| 56
SSM-5-A-L-x| 5.0| 125| 81 – 484| 15.75| 400| 5.00| 127| 25.58| 650| 10.00|
254| 11.90| 302| 171| 78
SSM-5-A-H-x| 5.0| 125| 101 – 594| 15.75| 400| 5.00| 127| 25.58| 650| 10.00|
254| 11.90| 302| 171| 78
SSM-6-A-L-x| 6.0| 150| 113 – 652| 17.76| 451| 5.49| 139| 27.26| 692| 10.98|
279| 14.00| 356| 241| 109
SSM-6-A-H-x| 6.0| 150| 141 – 859| 17.76| 451| 5.49| 139| 27.26| 692| 10.98|
279| 14.00| 356| 241| 109
SSM-8-A-L-x| 8.0| 200| 419 – 925| 23.62| 600| 7.48| 190| 27.38| 695| 14.96|
380| 18.58| 472| 386| 175
SSM-8-A-H-x| 8.0| 200| 572 – 1233| 23.62| 600| 7.48| 190| 27.38| 695| 14.96|
380| 18.58| 472| 386| 175
SSM-10-A-L-x| 10.0| 250| 837 – 2091| 28.74| 730| 8.74| 222| 33.44| 849| 17.48|
444| 21.69| 551| 677| 307
SSM-10-A-H-x| 10.0| 250| 1079 – 2642| 28.74| 730| 8.74| 222| 33.44| 849|
17.48| 444| 21.69| 551| 677| 307
SSM-12-A-L-x| 12.0| 300| 837 – 2091| 33.46| 850| 10.24| 260| 33.44| 849|
20.47| 520| 28.39| 721| 1036| 470
SSM-12-A-H-x| 12.0| 300| 1079 – 2642| 33.46| 850| 10.24| 260| 33.44| 849|
20.47| 520| 28.39| 721| 1036| 470
GA Series (Non-Spring Return) Actuators only Weights shown are for valve/actuator assemblies Add 3.2 lbs. (1.5 kg) for spring return GA(S) actuator
Simple Set Max – ANSI 250 Dimensions – 2-1/2″ – 12″
Simple Set Max Dimensions — 2-1/2″ – 12″ — ANSI 250 with GA(S) Series
Actuators| | | | | |
---|---|---|---|---|---|---
ANSI 250 Model Number| Valve Size| Flow Range| Please Reference the
Illustration| | | | | | | |
L| | W| | H| | H1| | D| | Weight|
x = Flow in GPM| in.| mm| GPM| in.| mm| in.| mm| in.| mm| in.| mm|
in.| mm| lb.| kg.
SSM-250-A250-L-x| 2.5| 65| 19| – 110| 11.50| 292| 7.50| 191| 3 .70| 95|
19.20| 487| 7.50| 189| 6 4 .0| 29
SSM-250-A250-H-x| 2.5| 65| 26| – 154| 11.50| 292| 7.50| 191| 3.70| 95|
19.20| 487| 7.50| 189| 64.0| 29
SSM-3-A250-L-x| 3| 80| 26| – 150| 12.50| 318| 8.30| 212| 4 .10| 104| 20
.0 0| 509| 8.20| 209| 88.2| 40
SSM-3-A250-H-x| 3| 80| 31 – 189| 12.50| 318| 8.30| 212| 4.10| 104| 20.0
0| 509| 8.20| 209| 88.2| 40
SSM-4-A250-L-x| 4| 100| 53 – 299| 14.50| 368| 10.80| 274| 5.0 0| 127|
25.30| 643| 10.00| 253| 167.6| 76
SSM-4-A250-H-x| 4| 100| 65 – 396| 14.50| 368| 10.80| 274| 5.00| 127|
25.30| 643| 10.00| 253| 167.6| 76
SSM-5-A250-L-x| 5| 125| 81 – 484| 16.60| 422| 12.30| 312| 5.50| 139| 26
.30| 668| 10.90| 277| 231.5| 105
SSM-5-A250-H-x| 5| 125| 101 – 594| 16.60| 422| 12.30| 312| 5.50| 139|
26.30| 668| 10.90| 277| 231.5| 105
SSM-6-A250-L-x| 6| 150| 113 – 652| 18 .6 0| 473| 14.40| 365| 6.30| 159|
28.10| 713| 12.50| 317| 319.7| 145
SSM-6-A250-H-x| 6| 150| 141 – 859| 18.60| 473| 14.40| 365| 6.30| 159|
28.10| 713| 12.50| 317| 319.7| 145
SSM-8 -A250 -L- x| 8| 200| 419 – 925| 23.60| 600| 18.6 0| 472| 7.50|
190| 28.20| 715| 15.00| 380| 392.4| 178
SSM-8-A250-H-x| 8| 200| 572 – 1233| 23.60| 600| 18.60| 472| 7.50| 190|
28.20| 715| 15.0 0| 380| 392.4| 178
SSM-10-A250-L-x| 10| 250| 8 37 – 20 91| 28 .80| 730| 21.70| 551| 8.70|
222| 34.20| 870| 17.5 0| 444| 685.6| 311
SSM-10-A250-H-x| 10| 250| 10 79 – 264 2| 28 .80| 730| 21.70| 551| 8.70|
222| 34.20| 870| 17.50| 444| 685.6| 311
SSM-12-A250-L-x| 12| 30 0| 837 – 2091| 33.50| 850| 28.40| 721| 10.20|
260| 34.20| 869| 20 .50| 520| 1047.2| 475
SSM-12-A250-H-x| 12| 300| 1079 – 2642| 33.50| 850| 28.40| 721| 10.20|
260| 34.20| 869| 20.50| 520| 1047.2| 475
GA Series (Non-Spring Return) Actuators only Weights shown are for
valve/actuator assemblies
Add 3.2 lbs. (1.5 kg) for spring return GA(S) actuator
CUSTOMER SERVICES
Bray Commercial Division
13788 West Road, Suite 200A
Houston, Texas 77041
BCDSales@Bray.com
Phone: 1-888-412-2729
www.braycommercialdivision.com
References
- Home - Bray Commercial Division
- GA(S) Series PIC & Globe Valve Actuators - Bray Commercial Division
- GA(S) Series PIC & Globe Valve Actuators - Bray Commercial Division
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>