Aqara Water Leak Sensor User Guide
- June 13, 2024
- Aqara
Table of Contents
Aqara Water Leak Sensor
Product Introduction
Aqara Water Leak Sensor detects water leaks and flooding and monitors their status. When a water leak or flooding occurs, it sends an instant alert notification via the app. It also works with other smart accessories to automate your home.
- A hub is required.
- Aqara Hub is required to enable Aqara Water Leak Sensor to work with HomeKit technology. See www.aqara.com for more details.
- This product is for indoor use only.
Indicator Light
- Inductive Probe
- Reset Button
- Long Press for 5s: Reset/Connect to Network
- Single Press: Effective Range Test
Quick Setup
- Before activating the accessory, please make sure you have the Aqara Home app downloaded and Aqara hub installed.
- Please open the app, tap Home and then tap + in the top right corner to enter Add Device (Accessory) page. Select Water Leak Sensor, and add it according to instructions. * If the connection fails, please move the accessory closer to the Hub and try again.
Installation
Effective Range Test: Single press the reset button on the accessory at your desired position. If the Hub makes voice prompts, it indicates that the accessory can communicate effectively with the Hub. * Avoid metal surface to maximize signal strength.
Option 1: Place it directly on the surface where you need to monitor
water leaks.
Option 2: Use a hex screwdriver to loosen the probes and connect to
cables for more smart scenes.
- In order to ensure the dustproof and waterproof performance of the product, the back cover of the battery must be tightened before use, and the groove is at the same level as the probe.
- The antenna is right above the water drop icon.
Battery Replacement
- Insert a coin into the groove of the battery cover and turn it counterclockwise to open the battery cover;
- Put a new CR2032 button battery into the battery compartment, and pay attention to making the side with the+ sign face out;
- Close and tighten the battery cover, and ensure that the groove of the battery cover is aligned with the metal probes on both sides in a straight line;
Specifications
- Online Customer Service: www.aqara.com/support
- Email: support@aqara.com
- Manufacturer: Lumi United Technology Co., Ltd.
- Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.
Warnings
- This product is NOT a toy. Please keep children away from this product.
- This product is designed for indoor use only. Do NOT use it outdoors.
- Do NOT place this product near a heat source. Do NOT place it in an enclosure unless there is normal ventilation. Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional.
- This product is only suitable for improving the entertainment and convenience of your home life and reminding you about the device status. If a user violates the product use instructions, the manufacturer will NOT be liable for any risks and property losses.
FCC ID: 2AKIT-SJCGQ11LM Federal Communications Commission (FCC) compliance statement: This device complies with part 15 of the FCC Rules.
Product Introduction
Aqara Water Leak Sensor detects water leak and flooding and monitors the status of water leak. When the water leak or flooding occurs, it sends an instant alert notification via app. It also works with other smart accessories to automate your home.
- A hub is required.
- Aqara Hub is required to enable Aqara Water Leak Sensor to work with HomeKit technology. See www.aqara.com for more details.
- This product is for indoor use only.
Quick Setup
- Before activating the accessory, please make sure you have the Aqara Home app downloaded and Aqara hub installed.
- Please open the app, tap “Home” and then tap “+” in the top right corner to enter “Add Device (Accessory)” page. Select “Water Leak Sensor”, and add it according to instructions.
If the connection fails, please move the accessory closer to the Hub and try again.
Installation
Effective Range Test: Single press the reset button on the accessory at your
desired position. If the Hub makes voice prompts, it indicates that the
accessory can communicate effectively with the Hub.
Avoid metal surface to maximize signal strength.
- Option 1: Place it directly on the surface where you need to monitor water leak.
- Option 2: Use a hex screwdriver to loosen the probes, and connect to cables for more smart scenes.
In order to ensure the dustproof and waterproof performance of the product,
the back cover of the battery must be tightened before use, and the groove is
at the same level as the probe.
The antenna is right above the water drop icon.
Battery Replacement
- Insert a coin into the groove of the battery cover and turn it counterclockwise to open the battery cover;
- Put a new CR2032 button battery into the battery compartment, and pay attention to making the side with the”+” sign face out;
- Close and tighten the battery cover, and ensure that the groove of the battery cover is aligned with the metal probes on both sides in a straight line;
Specifications
- Model: SJCGQ11LM
- Dimensions: 50 × 50 × 15 mm (1.97 × 1.97 × 0.59 in.) Wireless Protocol: Zigbee
- Battery: CR2032
- Operating Temperature: -10° – +55°C (14° – 131°F) Operating Humidity: 0 – 100% RH
- Maximum Transmit Power (Zigbee): 9.99dBm
- Working Frequency: 2400 MHz – 2483.5 MHz
- Online Customer Service: www.aqara.com/support
- Email: support@aqara.com
- Manufacturer: Lumi United Technology Co., Ltd.
- Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China.
Warnings
- This product is NOT a toy. Please keep children away from this product.
- This product is designed for indoor use only. Do NOT use in outdoors.
- Do NOT place this product near a heat source.
- Do NOT place it in an enclosure unless there is normal ventilation.
- Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional.
- This product is only suitable for improving the entertainment, convenience of your home life and reminding you about the device status.
- If a user violates the product use instructions, the manufacturer will NOT be liable for any risks and property losses.
FCC
FCC ID: 2AKIT-SJCGQ11LM
Federal Communications Commission (FCC) compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. 2. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter
IC: 22635-SJCGQ11LM
IC NOTICE TO CANADIAN USERS This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES‐003. This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter
CAUTION
Risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Do not ingest battery, Chemical Burn Hazard.
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it away from
children. If you think batteries might have been swallowed or placed inside
any part of the body, seek immediate medical attention.
- The equipment is only suitable for mounting at heights ≤ 2 m
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas
Hereby, [Lumi United Technology Co., Ltd.] declares that the radio equipment
type [Water Leak Sensor, SJCGQ11LM] is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at
the following internet address: http://www.aqara.com/DoC/
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the
recycling of waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about
the location as well as terms and conditions of such collection points.
Symbol on the product or on its packaging indicates that this product may not
be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>