On-Q HT5800 In-Ceiling and In-Wall Speakers Installation Instruction
- June 13, 2024
- On-Q
Table of Contents
On-Q HT5800 In-Ceiling and In-Wall Speakers
Introduction
On-Q/Legrand offers three (3) styles of evōQ™ 5000 series Home Theater
Speakers; In-Ceiling, Angled In-Ceiling and In-Wall plus a 10” Sub-Woofer.
There are two sizes of both the standard In-Ceiling and In-Wall styles
(6.5” and 8”) and one size (6.5”) of the Angled In-Ceiling speaker, each with
its own part number (as shown to the right). The speakers are optimized for
the demands of home theater sound. All models (except the Sub-Woofer) are
2-way speakers that feature Poly woofers and UFLC (Urethane Film Laminated
Cloth) Dome tweeters. The In-Ceiling and In-Wall speakers come with dual
templates with center markings and paint rings. Optional speaker pre-
construction brackets are available for them.
Note: *P/N HT5104, 10” 150W Sub-Woofer and HT5655, 6.5” Angled In-Ceiling speaker is for reference only and NOT part of this instruction sheet. See IS-0260 and IS-0384 (respectfully).
Disclaimer: Make sure you are in compliance with local building codes before installing these speakers.
In-Ceiling Style
(shown w/o grill)
6.5” – P/N HT5650 (ea.) 8” – P/N HT5800 (ea.)
6.5” Angled – P/N HT5655 (ea.) Angled In-Ceiling Style (not shown)
In-Wall Style
(shown w/o grill)
10” Sub – P/N HT5104 (ea.) 10” Sub-Woofer (not shown)
Description
The On-Q/Legrand evōQ™ 5000 series speakers are made of tough semi-flexible plastic frames that feature a built-in foam gasket to minimize vibration and maximize seal-ability. They also feature a perforated metal grill with a scrim cloth to enhance the speaker’s appearance once installed. All evóQ speakers, except sub-woofers, are paint-able. They also come with painting shields to protect the drivers while painting. These speakers are suitable for moisture- rich environments. They also feature flip-out tabs for easy installation and removal.
Installation
Installation of the evōQ™ 5000 speakers is best accomplished multiple times during new construction, at “Rough-in” before the drywall is installed, and at “Trim-out” after the drywall is installed and painted.
“Rough-in” steps:
-
NOTE: It is recommended that a minimum of 16 gauge, 2 conductor wire be used for most applications from the amplifier or volume control to the speaker. Different gauges can, and should, be used based on the distance of the intended run or the quality of installation (see Figure 2).
Speaker Wire Gauge Selection Chart -
NOTE: All On-Q/Legrand lyriQ™ Audio components accommodate wire gauges from 18 to 14.
- Run x/2 conductor (x=gauge preference) stranded speaker wire from the distribution/volume control to the speaker location (pre-wiring).
- If an On-Q Speaker Pre-Construction Bracket is to be used, skip to Step “5” and refer to IS-0243 for detailed instructions.
- If pre-wiring without using the On-Q Pre-Construction Speaker Brackets, leave 4 to 6 feet of wire at the speakers intended location. Use a strip of cardboard stapled to the joints/studs with a hole through it as a wire place holder for the drywall installers if installation of the speakers is intended (see Figure 3).
- After drywall and/or painting is complete, push the wire through hole, center template over hole, mark with a pencil and cut out with a dry-wall knife.
- When using the On-Q Pre-Construction Bracket (see Figure 4), leave a coil of speaker wire on top of the bracket coiled around the speaker mounting hole. There are clips on the corner of the bracket to secure the speaker wire. Leave enough speaker wire to be able to pull the wire through the bracket and comfortably connect the wire to the speaker after the drywall is installed. Strip off 3 inches or so of the speaker cable jacket to expose the positive and negative insulated wires. Strip 3/8-1/2 inch of insulation off of these conductors.
- It is recommended to place insulation behind the speaker to provide some damping for the woofer driver. This will yield the best possible sound. On-Q recommends using poly-encapsulated insulation such as Johns Manville Comfort Therm®. If a defined, consistent sound is desired from both speakers in a space, blocking can be installed to yield the ideal cubic footage for each driver. Insulation would then be put in this space during speaker installation. Refer to blocking chart for details.
- If installing speakers in a space with an attic above it is recommended that the speakers be boxed in with 1/2 inch MDF (medium density fiber board) or plywood with insulation installed. This will provide a defined acoustic space and protect the speaker. The best possible sound will be achieved by doing this. Refer to the blocking chart for details.
Note: Make sure you are in compliance with local building codes before installing this speaker in an attic space.
“Trim-out” steps:
-
After drywall and/or painting is complete, push the speaker wire through hole, center template over hole, mark with a pencil and cut out with a dry-wall knife.
-
Hold the speaker with one hand, (if speaker grill is off, pay careful attention not to push on the woofer’s cone, this can cause permanent contortion of the voice coil, thus producing a mechanical rubbing sound or speaker failure), push in the speaker terminal connectors and insert wires; remove speaker grill. Be sure to have the positive wire in the RED terminal and the negative wire in the BLACK terminal.
NOTE: Wiring both speakers identically as the above instruction states will yield speakers that are “in phase”. If one speaker is wired opposite of the other, the speakers will be “out of phase” with one another. If the speakers are “out of phase” the sound might appear smeared (canned) and a significant loss of bass might be noticeable due to phase cancellation. Make sure every installed speaker is correctly phased. -
Use one hand to push the speaker into the cut out (again, pay careful attention not to push on the woofer’s cone, this can cause permanent contortion of the voice coil, thus producing mechanical rubbing sound or speaker failure) and the other to turn the screws that engage the installation tabs (see Figure 5). Tighten the tabs in a cross or X-pattern until “snug”. Be careful not to over tighten the tabs or damage could result. The speaker should appear flush to the surface.
- NOTE: If using a cordless drill/screwdriver, it is suggested that the screws be turned until almost tight, then finish tightening via a hand screwdriver.
- NOTE: A strip of grill adhesive is provided to more securely attach the speaker grills on final installation. Simply insert several short strips evenly around the grill slot prior to installing the grill cover.
evōQ™ Speaker Blocking Chart
| 6.5″ Speaker (0.7 CuFt) | Blocking Distance |
|---|---|
| 16″ on Center, 2×4 | 24.00″ |
| 16″ on Center, 2×6 | 15.25″ |
| 16″ on Center, 2×8 | 11.50″ |
| 16″ on Center, 2×10 | 9.00″ |
| 16″ on Center, 2×12 | 7.50″ |
| 24″ on Center, 2×4 | 15.50″ |
| 24″ on Center, 2×6 | 10.00″ |
8″ Speaker (2.1 CuFt)| Blocking Distance
16″ on Center, 2×4| 71.50″
16″ on Center, 2×6| 45.50″
16″ on Center, 2×8| 34.50″
16″ on Center, 2×10| 27.00″
16″ on Center, 2×12| 22.25″
24″ on Center, 2×4| 46.00″
24″ on Center, 2×6| 29.50″
Speaker Specifications
| HT5650 | HT5651 | HT5800 | HT5801 | HT5655 | |
|---|---|---|---|---|---|
| Size/Type | 6.5″ In-Ceiling | 6.5″ In-Wall | 8″ In-Ceiling | 8″ In-Wall | 6.5” |
Angled In-Ceiling
Efficiency| 90dB| 90dB| 90dB| 90dB| 90dB
Power (RMS/Peak)| 75W/150W| 75W/150W| 100W/200W| 100W/2000W| 75W/150W
Frequency Response| 60-20K| 60-20K| 50-20K| 50-20K| 60-20K
Woofer Type| Poly| Poly| Poly| Poly| Poly
Tweeter Type| UFLC| UFLC| UFLC| UFLC| UFLC
Drywall Hole Size| 7.75” dia.| 7.5” x 10.75”| 9.5” dia.| 8.75” x 12.75”| 9.5”
dia.
FREQUENTLY ASKED QUESTIONS
What is the On-Q HT5800 In-Ceiling and In-Wall Speaker?
The On-Q HT5800 is a line of in-ceiling and in-wall speakers designed for home audio and theater installations.
What are the key features of the On-Q HT5800 speakers?
The key features include a discreet design, easy installation, quality sound reproduction, pivoting tweeters for directing sound, and paintable grilles to match the decor.
What sizes are available for the On-Q HT5800 speakers?
The On-Q HT5800 speakers are available in various sizes, including 6.5-inch and 8-inch options.
What type of audio quality can be expected from these speakers?
The On-Q HT5800 speakers offer high-quality audio with clear sound and good bass response, ideal for home theater setups and background music.
Can the On-Q HT5800 speakers be used for both in-ceiling and in-wall installations?
Yes, these speakers are versatile and can be used for both in-ceiling and in- wall applications.
Are these speakers suitable for outdoor use?
The On-Q HT5800 speakers are primarily designed for indoor use. While they might work in covered outdoor spaces, they are not designed for direct exposure to the elements.
How many speakers come in a package?
Typically, On-Q HT5800 speakers are sold individually, so you can buy as many as needed for your specific setup.
What is the power handling capacity of these speakers?
The power handling capacity may vary depending on the specific model, but generally, they can handle anywhere from 60 to 100 watts RMS.
Can the On-Q HT5800 speakers be used as part of a surround sound system?
Yes, these speakers are well-suited for use as surround speakers in a home theater setup.
Do the speakers come with a warranty?
On-Q typically provides a limited warranty for their products, including the HT5800 series speakers. The warranty duration may vary, so it's essential to check with the manufacturer or retailer.
How are the On-Q HT5800 speakers installed?
The speakers are designed for easy installation. In-ceiling models can be mounted using the included brackets, and in-wall models can be installed into standard wall cavities.
Are these speakers compatible with different audio systems and receivers?
Yes, the On-Q HT5800 speakers feature standard speaker connections and are compatible with most audio systems and AV receivers.
Can the grilles of the speakers be painted to match the room's color?
Yes, the grilles are paintable, allowing you to customize them to match your room's color scheme.
What is the frequency response range of the On-Q HT5800 speakers?
The frequency response typically falls within the range of 50Hz to 20kHz.
Are these speakers suitable for use in multi-room audio systems?
Yes, the On-Q HT5800 speakers can be integrated into multi-room audio setups, providing a consistent audio experience throughout your home.
Download the PDF Link:On-Q HT5800 In-Ceiling and In-Wall Speakers Installation Instruction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>