HILTI HVU2 Adhesive Capsule Instruction Manual
- June 13, 2024
- HILTI
Table of Contents
HILTI HVU2 Adhesive Capsule
Product Information
The product is the HVU2, a versatile tool for hammer drilling and diamond coring. It is designed to work with various anchor sizes and can be used in different types of concrete, both cracked and uncracked. The product has different variants for different regions and languages.
Product Usage Instructions
To use the HVU2 for hammer drilling:
- Choose the appropriate variant of the HVU2 based on your language and region.
- Select the anchor size that matches your requirements.
- Refer to the table provided to determine the exact measurements for d0 (diameter), h0 (exact height), df (final diameter), hmin (minimum height), and Tinst (recommended torque).
- Ensure that the concrete you are drilling into is suitable for hammer drilling, either uncracked or cracked depending on your needs.
- Use a suitable power tool, such as Hilti VC 20/40 (-Y) with a minimum flow rate of 57 l/s, along with compatible drill bits, such as TE-C HVU2 or TE-Y HVU2.
- Follow the recommended RPM range for the power tool, which is 450 to 1300.
To use the HVU2 for diamond coring:
- Choose the appropriate variant of the HVU2 based on your language and region.
- Select the anchor size that matches your requirements.
- Refer to the table provided to determine the exact measurements for d0 (diameter), h0 (exact height), df (final diameter), hmin (minimum height), and Tinst (recommended torque).
- Ensure that the concrete you are coring into is suitable for diamond coring, either uncracked or cracked depending on your needs.
- Use a suitable power tool, such as Hilti VC 20/40 (-Y) with a minimum flow rate of 57 l/s, along with compatible drill bits, such as TE-C 1/2 or TE-Y 3/4.
- Follow the recommended RPM range for the power tool, which is 450 to 1300.
Note: Make sure to use the correct power tool and drill bit combinations mentioned in the table based on your requirements.
HVU2
Tools Required
HVU2 + HAS …
HVU2 + HIS-N, -RN
Tools
Assembly
Installation
Hilti HVU2 adhesive anchor capsule for anchor fastening in concrete
- Prior to use of product, follow the instructions for use and the legally obligated safety precautions. Read the Safety data sheet for this product .Selection of appropriate protective equipment is in the responsibility of the user.
Hilti HVU2
Danger Restricted to professional users. Contains: dibenzoyl peroxide; dicyclohexyl phthalate; 2-Hydroxypropyl methacrylate; 1,4-Butanediol dimethacrylate; May cause an allergic skin reaction, May damage the unborn child; Toxic to aquatic life with long lasting effects. Wear eye protection, protective clothing, protective gloves, Do not get in eyes, on skin, or on clothing, IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing, IF ON SKIN: Wash with plenty of water, If eye irritation persists: Get medical advice/attention, If skin irritation or rash occurs: Get medical advice/attention;
Disposal considerations: Unusable foil capsules e.g. if expiry date has been exceeded, should be disposed of as hazardous waste material under observance of the official regulations. EAK code no.: 20 01 27 or 08 04 09*
Product Information:
- Always keep this Instruction for Use together with the product.
- Ensure that the Instruction for Use is with the product when it is given to other persons
- Check expiration date: See expiration date printed on the sales packaging (box) and capsule. Do not use expired product.
- Do not use knife to open bulk packaging. Check if capsule is damaged. Use only undamaged capsules!
- Installation temperature (base material, capsule, anchor rod): –10 °C to 40 °C / 14°F to 104°F
Conditions for transport and storage:
- Keep in a cool, dry and dark place between 5 °C to 25 °C / 41 °F to 77 °F.
Suitable for anchor fastenings in concrete with a minimum compressive strength of 15 N/mm² (2000 psi). Approval requirements must be observed!
For any application not covered by this document, contact Hilti.
WARNING
Poor load values / potential failure of fastening due to oversetting. Stop
rotation of anchor rod immediately when the embedment depth is reached.
-
Ensure the correct marking of the embedment depth on the drill bit and threaded rod.
-
Check that the hole is drilled to the correct depth before setting the anchor. Hole depth is correct when the anchor rod contacts the base of the hole and the setting depth mark coincides with the concrete surface.
-
Use the setting machine at a speed of 450–1300 RPM to drive the anchor rod into the hole, applying moderate pressure. Switch off the setting machine immediately when the setting depth is reached (refer to mark on the anchor rod). After setting, adhesive mortar must fill the annular gap completely, right up to the concrete surface. Caution! Prolonged rotary action may cause mortar to be forced out of the hole, resulting in poor load values / potential failure of fastening.
-
Ensure that the specified anchor rod is used.
Poor load values / potential failure of fastening due to inadequate borehole cleaning -
Hilti hollow drill bits TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity (volumetric flow rate) as specified in the accessory table.
-
Borehole must be free of dust, water, ice, oil, bitumen, chemicals or any other foreign matter or contaminants.
-
Clean the borehole right before setting the anchor. Remove drilling dust and standing water from the base of the hole by blowing out well with at least 4 strokes of the Hilti blow pump, or using oil-free compressed air.
Not adhering to these setting instructions can result in failure of fastening points!
For diamond cored holes:
- Only use specified wire brush for cleaning the borehole. Wear-out of brushes will lead to reduction in cleaning quality and may lead to poor load values. Please replace the brushes.
- For requirements at application temperature below 0°C, contact Hilti.
For overhead application: Use HIT-OHC as a drip guard.
Loading or manipulation of anchor rod is not allowed within the curing time «t
cure». Overhead application is not permitted for HVU2 M27 and M30
Warranty: Refer to standard Hilti terms and conditions of sale for warranty information.
Failure to observe these installation instructions, use of non-Hilti anchor rods, poor or questionable concrete conditions, or unique applications may affect the reliability or performance of the fastenings.
Hilti (Gt. Britain) Ltd.
1 Trafford Wharf Road
Trafford Park
GB-M17 1BY Manchester
Tel +44 161 886 1000
Made in Germany
www.hilti.group
Hilti = registered trademark of Hilti Corporation, Schaan, L
Printed in Germany © 2023
Right of technical changes reserved S.E. & O.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>