Lucci 018391 2 Light Drop Pendant Instruction Manual

: June 13, 2024
: Lucci

Table of Contents

Lucci 018391 2 Light Drop Pendant
Product Information
Product Usage Instructions
Warranty
Installation Requirements
Installation Directions
Safety Tips
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lucci 018391 2 Light Drop Pendant

Product Information

Product Name: DOMUS 2 LIGHT SES DROP PENDANT
SKU: 018391
Colour: Aged Brass with Frosted Opal Glass shade
Rated Voltage: 220-240V~ 50Hz
Rated Wattage: 56W Max. (2 x Max. 28W)
Lamp Holder: SES / E14
Weight: 2.1kg
Canopy Dimensions: H:25mm Dia:100mm
Luminaire Dimensions: L:270mm W:90mm H:1030mm
Susp: 1200mm

Product Usage Instructions

Remove all packaging material from the product and be careful not to throw away any hidden accessories.
Lay the luminaire on its side on a smooth non-scratch surface for assembly.
Install the different sections of suspension rods (G, H, I) onto the body (J) of the luminaire. Feed the cord (O) through as you assemble to remove any slack. Take care not to cross thread or twist and damage the cord (O).
Pull the cord (O) up into the canopy (F) and attach the canopy (F) to the top of the suspension rod.
Install the figure 8 shape cord anchorage (N) onto the cord (O) inside the canopy, leaving enough room for connection to the terminal block (D).
Remove the mounting bracket (B) from the canopy (F) by loosening the screws (E) on the sides.
Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.
Install the mounting bracket (B) onto the ceiling using appropriately sized mounting screws (C) and anchors (A). Ensure the screws (C) and anchors (A) are suitable for the mounting surface and the surrounding environment.
Connect the mains supply wire and luminaire wires together to the terminal block (D). Follow the color-coding:
Mains Supply Wire: Yellow/Green or Blue or N
Fitting Wire: Brown or L
Note: This luminaire is a Class I product and must be earthed during wiring and installation.
Ensure the wires are secure and no bare wires are exposed.
Install the canopy (F) onto the mounting bracket (B) and secure it by tightening the screws (E) on the sides.
After full assembly and installation, switch on the luminaire to test and enjoy your new lighting product.

To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

This luminaire is covered by a 12- month warranty. The warranty is from date of purchase, not the date of installation.
If the luminaire is not assembled and installed by a licensed electrician the warranty will be void.
Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty inquiries.
Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

This luminaire must be assembled and installed by a licensed electrician.
All wiring and installation of the light fitting must adhere to local and national wiring rules. eg. AS/NZS 3000 Electrical installations.
This luminaire is a Class I product and must be earthed during wiring and installation.
Do not exceed the maximum wattage rating.
Select a suitable location for installation:
- This product is suitable for indoor use only.
- The mounting point must support 2 times the weight of the fitting.
- Ensure the luminaire is not installed in direct line of an air vent/system.
- When installing a luminaire in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. To help with assembly, lay the luminaire on its side on a smooth non scratch surface.
Decide on the suspension length of your pendant by installing the different sections of suspension rods (G, H, I) onto the body (J) of your luminaire. Feed the cord (O) through as you assemble to remove any slack. Take care not to cross thread or twist and damage the cord (O).
Pull the cord (O) up into the canopy (F) and attach the canopy (F) to the top of the suspension rod.
Install the “figure 8” shape cord anchorage (N) onto the cord (O) inside the canopy. Ensure to leave enough room for connection to the terminal block (D).
Remove the mounting bracket (B) from the canopy (F) by loosening the screws (E) on the sides.
Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.
Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (C) and anchors (A). Ensure the screws (C) and anchors (A) used are suitable for the mounting surface and the surrounding environment.
Connect the mains supply wire and luminaire wires together to the terminal block (D).
Mains Supply Wire Fitting Wire
Earth – Yellow/Green Yellow/Green or
Neutral – Blue or Black Blue or N
Live – Brown or Red Brown or L
NOTE: This luminaire is a Class I product and must be earthed during wiring and installation.
Ensure the wires are secure and no bare wires are exposed.
Install the canopy (F) onto the mounting bracket (B) and secure by tightening the screws (E) on the sides.
Install globes (L – Not included) into the lamp holders (K). Do not exceed the maximum wattage rating.
Install the glass shades (M) onto the body (P) of luminaire.
After the full assembly and installation, switch on the luminaire to test and enjoy your new lighting product.

Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
Select a suitable location away from liquids and hazards.
Ensure that the luminaire does not come in contact with corrosive chemicals, etc.
To clean, wipe with a damp clean cloth. Never soak the luminaire with water.