NVX BE-KIAOPTG3-VS102 Series Bass Enclosure Installation Guide

June 13, 2024
NVX

NVX BE-KIAOPTG3-VS102 Series Bass Enclosure

Product Information

Product Name: BE-KIAOPTG3-VSW104 B.O.O.S.T. Series Bass Enclosure

Compatible with: 2011-2015 Kia Optima

Included Hardware: (2) Teks- Self Drilling Roofing Screws, #12 2

Product Usage Instructions

  1. Lift, then fold the carpet to expose (2) Phillips screws on the driver’s side, then remove them.
  2. Run the speaker wire to the desired location. This wire will connect your subwoofer to the amplifier. It is recommended to run it behind the carpet.
  3. Connect the subwoofer wires to the connection terminal on your BOOST box. Typically, blue is used for positive (red) and grey for negative (black).
  4. Remove the 8 4mm Allen key screws from the subwoofer enclosure, then take out the subwoofer from the enclosure.
  5. Place the BOOST enclosure into position on the driver’s side, ensuring that the bottom holes line up with the holes in the trunk floor.
  6. Use the included hardware to secure the BOOST box into the trunk. You can use the factory screw location as seen in step 1.
  7. Wire the subwoofer in parallel for a final impedance of 2-Ohms. Connect the red wire to the red terminal and the black wire to the black terminal.
  8. Load the subwoofer back into the enclosure and fasten the 8 Allen bolts. Now you can enjoy your new BE-KIAOPTG3-VSW104!

Installation Instructions

Step 1

  • Lift, then fold carpet to expose (2) phillips screws on drivers side, then remove.

Step 2

  • Run speaker wire to desired location. This will connect your subwoofer to the amp.
  • We chose to run it behind the carpet.

NVX-BE-KIAOPTG3-VS102-Series-Bass-Enclosure-fig-2

Step 3

  • Connect subwoofer wires to the connection terminal on your BOOST box.
  • We generally use blue for positive (red) grey for negative (black).

NVX-BE-KIAOPTG3-VS102-Series-Bass-Enclosure-fig-3

Step 4

  • Remove the 8 4mm allen key screws from the subwoofer enclosure, then remove the subwoofer from the enclosure.

Step 5

  • Place BOOST enclosure into position on the drivers side. Make sure the bottom holes line up with the holes in the trunk floor.

Step 6

  • Take included hardware and secure the BOOST box into the trunk using the factory screw location as seen in step 1.

Step 7

  • Wire the subwoofer in parallel for a final impedance of 2-Ohms. Red wire goes to the red terminal and the black wire goes to the black terminal.

Step 8

  • Load the subwoofer back into the enclosure. Fasten the 8 allen bolts. Now it’s time to enjoy you’re new BEKIAOPTG3- VSW104!

  • We recommend the installation of the NVX BE-KIAOPTG3-VSW104 to be performed by a professional that will have the skills and tools to ensure the job is done correctly.

  • Please follow the steps above to get the best performance out of the BE-KIAOPTG3-VSW104.

  • Installing and mounting NVX BEKIAOPTG3- VSW104 improperly can present a serious safety hazard in the event of a collision.

  • If you have any questions regarding the installation of this product or an amplifier in this vehicle please feel free to contact NVX directly for further guidance and installation techniques.

Included Hardware

  • (2) Teks- Self Drilling Roofing Screws, #12 2″.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals