KV NUM MONT-011 Shelves Instruction Manual

KV NUM MONT-011 Shelves

Product Information

Product Name: Liljencrantz and Spira Shelves
Product Type: Shelving Units
Manufacturer: Liljencrantz

Product Usage Instructions

1. Assembling the Liljencrantz Shelf:
   • Place something soft on the floor to protect the shelf during assembly.
   • Assemble the shelf on its back.
   • Use the supplied 5.0×80 screws.
   • The two outer columns are fitted 150 mm cc from the outer edges of the shelf.
   • Shelves over 1600 mm in width have 3 columns. The third column is fitted in the center of the shelf. – Fit the pillar with the narrow part up into the keyhole fitting.
   • Column with keyhole fittings.
2. Mounting the Liljencrantz Shelf on the Wall:
   • Mount a screw in the wall for hanging keyhole fittings (wall screw not included in delivery).
   • Hang the shelf on the wall screw.
   • Make sure the shelf is level.
3. Assembling the Spira Shelf:
   • Place something soft on the floor to protect the shelf during assembly.
   • Thread the pillars through the holes of the shelves as shown.
   • Place the shelves in the correct order, with the lower and upper shelf having recesses for blocks with keyhole fittings.
   • Place the shelves correctly with the front edge and back edge as shown in the picture.
   • Follow the attached construction drawing for shelf placement.
   • Install screws through blocks and into pillars (4.5 x 70).

Note: Shelves that exceed certain width and height measurements are delivered in parts and assembled on-site. Use a protective mat to protect the shelf during assembly. The number of columns and shelves varies depending on the finished size of the shelf. For further assistance, contact Montagesupport at +46 512 30 10 71 or email montagesupport@kvanum.com. Please refer to the user manual for detailed illustrations and additional information.

Assembly support
+46 512 30 10 71
montagesupport@kvanum.com
We reserve the right for possible printing errors and product changes.
Version 2023-02

Assembly of Liljencrantz shelf

Facts shelf Liljencrantz

Shelves that exceed a height of 1220 mm are delivered in parts and assembled on site.

Shelf, 3 column Width 1601–2390 mm

Shelf, 2 column Width 600–1600 mm
Shelf, 1 column Width 300 mm

Shelf dimensions

Assembling the shelf
Shelves over 1220 mm in height are supplied in parts and assembled in place. Place something soft on the floor to protect the shelf during assembly. Assemble the shelf on its back. Use the supplied 5.0×80 screws. The two outer column are fitted 150 mm cc from the outer edges of the shelf. Shelves over 1600 mm in width have 3 column. The third column is fitted in the centre of the shelf.

Parts

• shelf.
  

• Column square 50 x 50

• Cover strip square 20 x 20

• Mount screw in wall for hanging keyhole fittings. (wall screw not included in delivery). Then hang the shelf on the wall screw.

Make sure the shelf is level.

Screw the shelf to the wall. Screw the shelf to the wall with the included screw 5.0 X 80 or choose another screw depending on the design of the wall. Make sure the shelf is level.

Remove the protective film on the tape.

Turn around cover strip.

Press the cover strip firmly.

 Assembly of Spira wall shelf

Facts shelf Spira
Shelves that exceed certain width and height measurements are delivered in parts and assembled on site. Use a protective mat to protect the shelf during assembly. The number of columns and shelves varies depending on the finished size of the shelf.

The shelf is mounted on the wall on the rear blocks of the shelf in keyhole fittings. Mount with a suitable wall screw (screw not included in delivery).

Parts

• Column round Ø 25 mm
  

• Shelf 29 mm

• Front block angled

• Rear block rectangular

• Rear block rectangular with keyhole fitting

Assembly order

Place something soft on the floor to protect the shelf during assembly. Thread the pillars through the holes of the shelves as shown. It is important to place the shelves in the correct order, the lower and upper shelf must have re-cesses for blocks with keyhole fittings. also place the shelves correctly as the front edge and back edge as shown in the picture.

• Place the shelves according to the attached construction drawing.

  1. Placement of blocks with keyhole fittings.

  2. To get the shelf perpendicular, make a cross measurement.

  3. Pre-drill the screw holes of the blocks into the pillars with a Ø 2 mm drill.

  4. Apply wood glue to the dowel holes and then press the block into the shelf.

  5. Install screw through block and into pillar (4,5 x 70).

  6. Install screw in keyhole fitting/shelf (3,5 x 30).

  7. Pre-drill the rest of the blocks through screw holes into the pillars with a Ø 2 mm drill bit.

  8. Place wood glue in the dowel holes.

  9.  Install screw through block and into pillar (4,0×70).

  10. Turn the shelf around so that the front is facing up.

  11. Apply wood glue to the dowel holes on the shelf.
      

  12. Apply a tape over the block. The tape is removed when the glue has dried.

  13. Install the wall screw, carefully measure the location of the wall screw based on the shelf’s suspension fittings. (wall screw not included in delivery).

  14. Hang the shelf in the shelf’s keyhole fitting on the wall screw.

Notes

 Assembly of Spira floor shelf

Facts shelf Spira
Shelves that exceed certain width and height measurements are delivered in parts and assembled on site. Use a protective mat to protect the shelf during assembly. The number of columns and shelves varies depending on the finished size of the shelf.

The shelf stands on the floor and can be adjusted at the bottom with adjustable feet. The shelf must be anchored to the wall with the included anchor strip. Mount with a suitable wall screw (screw not included in delivery).

Parts

• Collumn round Ø 25 mm

• Shelf 29 mm

• Front blocks angled

• Rear block angled with screw holes

• Anchoring strip on shelf in wall

Assembly order

1. Place something soft on the floor to protect the shelf during assembly. Thread the pillars through the holes of the shelves as shown. Mount the shelves with the holes for the support blocks downwards.
2. To get the shelf perpendicular, make a cross measurement during the entire assembly.
3. Place the shelves according to the attached construction drawing.
4. Install all rear angled blocks with screw holes.
5. Apply wood glue to the dowel holes on the shelf.
6. Pre-drill the screw holes of the blocks into the pillars with a Ø 2 mm drill.
7. Install screw through block and into pillar (4,5 x 70).

8. Turn the shelf around so that the front is facing up.

9. Install all the front angled blocks
   

10. Apply wood glue to the dowel holes on the shelf.

11. Apply a tape over the block. The tape is removed when the glue. has dried.
    

12. Mount the shelf against the wall, set the shelf level using the adjustable feet.
    

13. Screw the fastening strip to the shelf (3,5×35) and then to the wall. ( wall screw not included ). Mount the fastening strip where it is least visible.
    

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>