CAT 26001 336 Hydraulic Excavator Instructions
- June 13, 2024
- CAT
Table of Contents
CAT 26001 336 Hydraulic Excavator Instructions
Safety instructions
A : The Cat vehicle is designed for hobby use only and may only be
operated on tracks and in spaces especially intended for this purpose.
WARNING! Do not use the Cat vehicle in road traffic.
B : Never operate the product on grass surfaces. Do not use the Cat
vehicle for transporting goods, persons or animals.
C : Never use the Cat vehicle outdoors during rain or snowfall. The car
must not be run through water, puddles and snow, and must always be kept
stored in a dry place.
D : Avoid running on courses which are laid exclusively with sand.
E : Do not expose the Cat vehicle to direct sunlight.
F : Never subject the Cat car to repeated changes of load — that means
continuously reversing it.
G : Never throw the car on the floor from a standing position.
H : The Cat vehicle must be inspected before and after operation, each
time it is used, to ensure that mar it has not become disassembled. Any screws
or nuts that may have become loosened during operation must be tightened.
Instruction Manual
Contents of package
1x Cat Vehicle 1x Controller
1x USB-C charger cable
1x LiPo rechargeable battery
Charging the rechargeable battery
This toy (vehicle) contains batteries that are non-replaceable. Take care only to charge the LiPo ‘1’ battery supplied with the LiPo charging unit (USB-C charger cable) also supplied. If you attempt to recharge the battery with any other LiPo battery charger or any other type of charger, this may result in serious damage. Please carefully read the previous chapter with warnings and guidelines on the usage of rechargeable batteries before proceeding. You can recharge the rechargeable battery with the respective USB-C charger cable from a computer USB port (USB 3.0) or a USB power supply unit with at least 1 A output voltage:
- Uncharged state: LED on the vehicle is off. 1
- Charging in process: LED on the vehicle lights red. 2
- Fully charged state: LED on the vehicle is off.
- It lasts about 210 minutes to recharge a discharged (NOT a deep-discharged) battery. When the battery is fully charged, the LED display on vehicle is off again. While charging, the power switch must be in the “OFF” position.
Always recharge the battery after use to prevent its becoming deep discharged. After use, the battery must be allowed to cool down for at least 20 minutes before it can be fully recharged. Recharge the battery occasionally (suggested every 2-3 months). Supply terminals are not to be short-circuited. Failure to treat the battery as described above can lead to its becoming de-fective. Never leave the battery unattended while it is being charged.
Inserting the batteries
Open the battery compartment with a screwdriver and insert the batteries in the remote control. me Please keep in mind the correct polarity. Different types of batteries or new and used batteries are not to be mixed. After having closed the compartment you can check all functions of the remote control with the help of the power switch on the front With the power-switch turned ON and proper functioning, the top center LED on the remote control will light up red.
Now you can drive the car
The Cat car and the remote control are bound as a factory setting.
- Switch the car ON at the ON/OFF switch.
- Switch on the controller. The LED on top of the controller will flash rhythmically. After a few me seconds, the LED of controller will be off, the binding procedure is complete when the vehicle moves slightly. The LED on the controller will only light up if a joystick is moved.
Thanks to 2 4 GHz technology, up to 12 cars can be run together on one race- track. This is possible even without harmonising frequencies between the racing drivers.
• Avoid constant motor operation. • If the car switches itself off several
times one after another, the battery is dead. Please recharge the battery. •
Clean the Cat car after use.
Controller functions Model drive control
Troubleshooting
Problem: Car does not move.
Cause: Either the switch on the controller or the car is set to OFF.
Solution: Switch on.
Cause: There is no rechargeable battery in the car or the battery is too
weak.
Solution: Insert charged battery.
Cause: The battery or rechargeable battery in the transmitter or model is
too weak.
Solution: Insert new battery or recharged battery.
Cause : The remote control is possibly not correctly frequency bound with
the receiver on the model.
Solution: Carry out a frequency bind between the model and the remote
control as described in “Now you can drive the car”.
Cause: Within approx. 30 minutes of inactivity, the controller and
vehicle switch off automatically.
Solution: To restart, switch the ON/OFF switch on both controller &
vehicle to OFF and then back to ON.
Cause: The vehicle is very warm.
Solution: Switch both car and controller off and allow the car to cool
down for about 30 minutes.
Cause: The overheat protection has caused the car’s motor to cut out due
to excess temperature.
Solution: Switch off the receiver. Leave the RC car to cool down for
approx. 30 minutes.
Problem: Car cannot be controlled.
Cause: Vehicle starts moving unintentionally.
Solution: First turn on the vehicle, only then the transmitter 4/5
Errors and changes excepted. Colors / final design — changes excepted
Technical changes and design-related changes excepted. Pictograms = symbolic
photos
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
FCC compliance statement
This device complies with pad 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- – Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this product not authorized by
Diecast Masters could void the user’s authority to operate the equipment.
Responsible party (contact for FCC matters only):
Diecast Masters
12717 W Sunrise Blvd #418
Sunrise, FL 33323
Tel: +1 954-473-2201
www.diecastmasters.com
©2023 Diecast Masters Company Limited
Room 1801-5, 18/F
King Palace Plaza 52A Sha
Tsui Road Tsuen Wan, N.T., Hong Kong
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>