Panasonic AW-UE20 4K/30P Zoom Certified PTZ Camera Instruction Manual

Network Settings
Use the Easy IP setup Software to Establish the Unit’s Settings
The settings related to the unit’s network can be established using the Easy IP Setup Software. You can obtain Easy IP Setup Software (EasyIPSetup.exe) by downloading it from the following website. https://pro-av.panasonic.net/ To establish the settings for a multiple number of units, the settings must be selected for each camera involved. If the settings cannot be established using the Easy IP Setup Software, select the settings separately for the unit and personal computer on the Network setup screen [Network] of the setting menu. [Note] If, after the network settings have been established, another device in the same network has the same IP address,
the network operations will not be performed properly. Set the IP address in such a way that it does not duplicate an existing IP address. Do not establish network settings from a multiple number of Easy IP Setup Software programs at the same time for
a single camera. Similarly, do not perform the “Auto IP setting” operation of the remote camera controller AW-RP150 or AW-RP60 at the same time. The IP address settings may no longer be recognized as a result. To enhance the security of the Easy IP Setup Software, it will not be possible to make network settings for the target camera once about 20 minutes or more have elapsed after turning the power of the camera on. (When the [Easy IP Setup accommodate period] setting is [20min] ) The Easy IP Setup Software cannot be used from a different subnet via a router. 1. Start the Easy IP Setup Software. 2. Click the [Search] button.
29

3. Click the MAC address/IPv4 address of the camera to be set, and click the [Network Settings] button.
[Note] When a DHCP server is being used, the IP address allocated to the unit can be checked by clicking the [Search] button of the Easy IP Setup Software. If the same IP address is used for any additional cameras, the numbers of the additional cameras will be displayed
in the [IPv4 overlap] column of the cameras concerned. When the [Access Camera] button is clicked, the live screen of the selected camera is displayed. 4. Input the network items, and click the [Save] button.
[Note] When a DHCP server is being used, [DNS] of the Easy IP Setup Software can be set to [Auto]. After the [Save] button is clicked, it takes about 1 minute for the settings in the unit to be completed. If the AC
adaptor or LAN cable is disconnected before the settings are completed, the settings will be canceled. In this case, repeat the steps to establish the settings. When a firewall (including software) has been introduced, enable access to all the UDP ports.
30

Use the EasyIP Setup Tool Plus Software to Establish the Unit’s Settings
The settings related to the unit’s network can be established using the Easy IP Setup Software. You can obtain EasyIP Setup Tool Plus Software (EasyIPSetupToolPlus.exe) by downloading it from the following website: https ://pro-av.panasonic.net/ To establish the settings for a multiple number of units, the settings must be selected for each camera involved. If the settings cannot be established using the EasyIP Setup Tool Plus Software, select the settings separately for the unit and personal computer on the Network setup screen [Network] of the setting menu. [Note] If, after the network settings have been established, another device in the same network has the same IP address,
the network operations will not be performed properly. Set the IP address in such a way that it does not duplicate an existing IP address. Do not establish network settings from a multiple number of Easy IP Setup Software programs at the same time for
a single camera. Similarly, do not perform the “Auto IP setting” operation of the remote camera controller AW-RP150 or AW-RP60 at the same time. The IP address settings may no longer be recognized as a result. To enhance the security of the EasyIP Setup Tool Plus Software, it will not be possible to make network settings for the target camera once about 20 minutes or more have elapsed after turning the power of the camera on. (When the [Easy IP Setup accommodate period] setting is [20min]. The EasyIP Setup Tool Plus Software cannot be used from a different subnet via a router.
1 Double-click EasyIPSetupToolPlus.exe to start the Easy IP Setup Software. 2 Click the [Search] button.
31

3 Click the MAC address/IPv4 address of the camera to be set, and click the [Network settings] button.
When a DHCP server is being used, the IP address allocated to the unit can be checked by clicking the [Search] button of the Easy IP Setup Software.
If the same IP address is used for any additional cameras, the numbers of the additional cameras will be displayed in the “IPv4 overlap” column of the cameras concerned.
When the [Web GUI] button is clicked, the Live screen of the selected camera is displayed. The screen display of EasyIP Setup Tool Plus may vary by its version.
4 Input the network items, and click the [Setup] button.
When a DHCP server is being used, [DNS] of the Easy IP Setup Software can be set to [Auto]. After the [Save] button is clicked, it takes about 1 minute for the settings in the unit to be completed. If the AC adaptor or LAN cable is disconnected before the settings are completed, the settings will be canceled. In
this case, repeat the steps to establish the settings. When a firewall (including software) has been introduced, enable access to all the UDP ports.
32

Setting the Initial Account
1. Set the initial account. In the initial state, the initial account setting screen is displayed when the web screen is displayed. Set a user name and password.
[Note] The usable symbols for user name is following (# % + = , – ^ / @ . ~) Do not set character strings that can be easily guessed by third parties. Change the password at regular intervals. The password must use at least 3 of the following 4 character types and be 8 characters or longer.
– Alphabet upper cases – Alphabet lower cases – Numerals – Symbols (# % + = , – ^ / @ . ~ ) When a password is set that does not adhere to the above policy, take responsibility for use of the device with due consideration for the security risks in the installation environment, etc. A warning is displayed if the set password goes against the recommended setting policy. When changing the password, click the [Back] button and set the password again. When continuing with the setting with full understanding of the security risks, click [Continue] to complete the setting. If you forget the account information that was set, use the switches for initialization of service switches to reset the user information used for connecting to the network. ( page 23)
33

2. Completing registration of the initial account After completing registration of the initial account, the following registration completed screen is displayed. The live screen [Live] is automatically displayed after about 10 seconds elapse after the completed screen is displayed. If the live screen [live] is not displayed after 10 seconds elapse, manually move to the live screen [Live] by clicking the “please click here” link. This completes the process of registering the initial account.
34

Basic Shooting Operation
With the basic operations, it is assumed that the white balance will be adjusted automatically (as per the factory settings). 1. Make sure the subject brightness is in the appropriate level. 2. Make sure the unit and all devices are well connected and power on. 3. Press one of the [CAMERA 1] to [CAMERA 4] buttons on the wireless remote control to select the unit if using the
wireless remote control. Even when using only one unit, it must still be selected from the wireless remote control or controller. 4. Select the scene (shooting) mode. One of the three shooting modes (Full Auto, Scene1, Scene2)– whichever one will best suit the shooting conditions — can be selected. The shooting modes are set by the user. For details of the factory settings, refer to pages 66 to 68. Select the mode that satisfies the shooting conditions and suits your preferences. When continuing to shoot in the same circumstances, there is no need to select another mode. 5. Start shooting. [Note] Due to the characteristics of the lens, the edge of the image is distorted. If using a controller, please upgrade the unit with the latest firmware version.
35

Power on and Power Off the Camera Unit
Power on the Camera Unit
When performing the operations using the wireless remote control.
Set all the power switches of the units and devices connected in the system to ON. When the power is supplied, the status display lamp lights orange. After the initial setting is completed, it switches to green and the power turns on.
[Note] During the initial settings operation, the unit cannot be operated. The unit stores its STANDBY / POWER ON mode status in the memory. If the power supply is cut off while the operation is in POWER ON mode, the operation will transfer to the POWER
ON mode the next time power is supplied. When transferring to the STANDBY mode
– Status indicator LED: Orange – The current pan-tilt position is stored in the memory (as a POWER ON preset), and the panning/tilting moves so
that the camera points in the backward-facing direction. When transferring to the POWER ON mode
– Status indicator LED: Green (after the initial setting operation is completed) – The pan/tilt position is moved to the position which was stored in the memory when the transition to the
STANDBY mode was made. POWER ON preset
– The pan/tilt position return to the place just before entering STANDBY mode when returning from STANDBY mode to POWER ON mode.
If the power is turned off without transferring to the STANDBY mode, the pan/tilt unit position will not be stored in the memory or reflected in the POWER ON preset. The previous POWER ON preset will be applied.
When performing the operations using the controller (AW-RP60/AW-RP150). For details, refer to the operating instructions for the controller.
Power off the Camera Unit
When performing the operations using the wireless remote control
1. Press one of the [CAMERA 1] to [CAMERA 4] buttons on the wireless remote control to select the unit.
2. Press the [ON/STANDBY] button on the wireless remote control for 2 seconds. The unit enters STANDBY mode.
3. The unit’s status display lamp now lights up orange.
4. If a multiple number of units are used, repeat steps 1 and 2 as required.
5. Set all the power switches of the units and devices connected in the system to OFF.
When performing the operations using the controller (AW-RP60/ AW-RP150). For details, refer to the operating instructions for the controller.
36

Priority Mode
Changing the priority mode enables the unit to perform operation for various applications. HDMI (4K): 4K video is output to an external monitor connected via an HDMI cable. USB (4K): Enables the unit to be used as a 4K Web camera. The camera can also be controlled from a personal
computer. IP (4K): Enables IP image transmission. IP image transmission of 4K images uses the H.264/H.265 video coding
format. This unit cannot display H.264/H.265 format images on the Live screen. To display H.264/H.265 images, use an external device or external software that supports H.264/H.265 images. HDMI/USB: HD format video is output to an external monitor connected via an HDMI/SDI cable. Enables the unit to be used as a Web camera. The camera can also be controlled from a personal computer. IP: HD format video is output to an external monitor connected via an HDM/SDI cable. Enables IP image transmission. The IP transmission of H.264/H.265 images is also supported. This unit cannot display H.264/H.265 format images on the Live screen. To display H.264/H.265 images, use an external device or external software that supports H.264/H.265 images. USB (Video Conference): Enables the unit to be used as a Web camera. The camera can also be controlled from a personal computer. In this mode, you cannot output video via HDMI or SDI, and you cannot output video via IP transmission. (Video output will not be possible except via USB). Also, in this mode, the audio output is forcibly turned off.

Functions that can be and functions that cannot be controlled simultaneously.

Priority Mode

HDMI

HDMI (4K)

[50Hz] 2160/25p [59.94Hz] 2160/29.97p [60Hz] 2160/30p

3G-SDI

USB (4K)

IP (4K)

Output terminal

USB

RTSP/RTMP

LAN

Web (HTTP)

MJPEG [50Hz] 720/10fps360/25fps 10fps [59.94Hz/60Hz] 720/10fps360/30fps 10fps

H264:

[50Hz]

2160/25fps10fps5fps

[59.94Hz/60Hz]

2160/30fps15fps5fps

MJPEG:

2160/5fps

MJPEG [50Hz] 720/10fps360/25fps 10fps [59.94Hz/60Hz] 720/10fps360/30fps 10fps

MJPEG:

H264 or H.265:

[50Hz] [50Hz]

720/10fps360/25fps

2160/25fps10fps5fps 10fps

[59.94Hz/60Hz] [59.94Hz/60Hz]

2160/30fps15fps5fps 720/10fps360/30fps

10fps

37

Priority Mode
HDMI/USB

Output terminal

HDMI

3G-SDI

USB

[50Hz] 1080/50p, 1080/25p, 720/50p,1080/50i [59.94Hz] 1080/59.94p, 1080/29.97p, 720/59.94p, 1080/59.94i [60Hz] 1080/60p, 1080/30p, 720/60p,1080/60i

H264:

[50Hz]

1080/50fps25fps10fps

5fps720/50fps25fps

10fps5fps360/50fps

25fps10fps5fps

[59.94Hz/60Hz]

1080/60fps30fps15fps

[50Hz]

5fps720/60fps30fps

1080/50p, 1080/25p, 15fps5fps360/60fps

720/50p,1080/50i

30fps15fps5fps

[59.94Hz]

MJPEG:

1080/59.94p,

[50Hz]

1080/29.97p,

1080/25fps10fps5fps

720/59.94p,1080/59.94i 720/25fps10fps5fps

[60Hz]

360/25fps10fps5fps

1080/60p, 1080/30p,

[59.94Hz/60Hz]

720/60p,1080/60i

1080/30fps15fps5fps

720/30fps15fps5fps

360/30fps15fps5fps

YUV:

[50Hz]

360/10fps

[59.94Hz/60Hz]

360/15fps

RTSP/RTMP

LAN

Web (HTTP)

MJPEG: [50Hz] 720/10fps360/25fps 10fps [59.94Hz/60Hz] 720/10fps360/30fps 10fps

[50Hz] [50Hz]

1080/25p

1080/25p

[59.94Hz] IP [59.94Hz]

1080/29.97p

1080/29.97p

[60Hz] [60Hz]

1080/30p

1080/30p

H264 or H.265:

[50Hz]

MJPEG:

1080/50fps, 25fps, 10fps,

[50Hz]

5fps, 720/50fps, 25fps,

720/10fps, 360/25fps

10fps, 5fps, 360/50fps,

10fps

25fps, 10fps, 5fps

[59.94Hz, 60Hz] [59.94Hz/60Hz]

1080/60fps,

30fps,

15fps

720/10fps, 10fps

360/30fps

5fps, 720/60fps, 30fps,

15fps, 5fps, 360/60fps,

30fps, 15fps, 5fps

MJPEG:

[50Hz]

1080/25fps10fps5fps

720/25fps10fps5fps

360/25fps10fps5fps

[59.94Hz/60Hz]

USB (Video

1080/30fps15fps5fps

Conference)

720/30fps15fps5fps

360/30fps15fps5fps

YUV:

[50Hz]

360/25fps

[59.94Hz/60Hz]

360/30fps

38

Selecting the Camera Unit
When performing the operations using the wireless remote control
Press the [CAMERA 1], [CAMERA 2], [CAMERA 3] or [CAMERA 4] button. The camera unit’s status indicator LED blinks green when a signal matched by the remote control ID has been received, and it blinks orange when a signal that is not matched by the remote control ID has been received. When performing the operations using the controller (AW-RP60/AW-RP150). For details, refer to the operating instructions for the controller. Network connection with AW-RP60/AW- RP150 requires setup of an initial account. When an initial account is not setup, AW-RP60/AW-RP150 can detect but cannot control this unit.
Selecting the Scene Mode
Scene Mode Types
The unit has three preset scene modes, each of which corresponds to a set of circumstances in which the subject will be shot. Select the mode that satisfies the shooting conditions and suits your preferences. The settings can be changed by menu operations.
The results of the white balance and other adjustments are stored in the memory separately by shooting mode. Be absolutely sure to select the shooting mode before making any adjustments. Full Auto Under [Brightness], you can set Picture Level, AGC MaxGain, and Slow Shutter. Scene 1/Scene 2 Under [Brightness], you can set Picture Level, Iris Mode, Shutter Mode, Gain, and Frame Mix.
How to select the Scene mode
When performing the operations using the wireless remote control
1 Press the [CAMERA 1], [CAMERA 2], [CAMERA 3] or [CAMERA 4] button to select the unit. 2 Press the [MENU] button for 2 seconds.
The menu is displayed. 3 Press the [] or [] button to bring the highlight to “CAMERA”.
When performing the operations using the controller (AW-RP60/AW-RP150). For details, refer to the operating instructions for the controller.
39

4 Press the [ ] button. The “CAMERA” sub-menu is displayed on the monitor.
5 Press the [] or [] button to bring the highlight to “Scene”. 6 Press the [ ] button. 7 Press the [] or [] button to select the scene mode (Full Auto, Scene1, or Scene2) and press the [ ] button to confirm the selection. The selected scene mode has a mark sign within.
8 Press [] to leave from scene mode menu. 9 Press the [MENU] button for 2 seconds to exit from the menu.
40

Operating the Camera unit
When performing the operations using the wireless remote control
Control the Picture’s Direction (using the wireless remote control)
Moving the picture toward the left or right (panning): Press the [] or [] button. Moving the picture up or down (tilting): Press the [] or [] button. Moving the picture diagonally: Press the [] or [] button and [] or [] button at the same time. Returning the picture to the reference position: Press the [HOME] button for 2 seconds.
Zoom In/Out Function (using the wireless remote control)
Zooming in (the subject becomes magnified in size): Press the [T] button of [ZOOM]. Zooming out (the subject becomes reduced in size): Press the [W] button of [ZOOM].
Switching the Direction or Zoom Speed (using the wireless remote control)
Changing the direction or zoom at high speed: Press the [FAST] button. Changing the direction or zoom at low speed: Press the [SLOW] button. When performing the operations using the controller (AW-RP60/AW-RP150)
Control the Picture’s Direction (using the controller)
Moving the picture toward the left or right (panning): Tilt the <PAN/TILT> lever toward L or R. Moving the picture up or down (tilting): Tilt the <PAN/TILT> lever toward UP or DOWN. Moving the picture diagonally: Tilt the <PAN/TILT> lever diagonally.
Zoom In/Out Function (using the controller)
Zooming in (the subject becomes magnified in size): Tilt the lever toward the TELE direction. Zooming out (the subject becomes reduced in size): Tilt the lever toward the WIDE direction.
Switching the Direction or Zoom Speed (using the controller)
For details, refer to the operating instructions for the controller. 41

What to do when Encountering Problems in the Basic Shooting Operations
If the trouble is not resolved by taking the action suggested below, refer to “Troubleshooting” section.
When performing the operations using the wireless remote control
The unit does not move. – Press the [CAMERA 1], [CAMERA 2], [CAMERA 3] or [CAMERA 4] button to select the unit which is to be operated. – If only one unit is being used, it is normally selected using the [CAMERA 1] button. – Check that the Wireless ID has been set correctly. – If the unit’s status display lamp is off or lights up orange, it means that the unit’s power is not on. – Refer to “Power on the Camera Unit” section. – If the unit’s status display lamp does not blink even when the wireless remote control is operated near the unit’s wireless remote control signal light-sensing area, it means that the wireless remote control’s batteries have run down. Replace the batteries.
Multiple color bands (color bars) are displayed. Press the [MODE] button to switch to the camera picture.
The menu screen is displayed. Press the [MENU] button for 2 seconds to exit the camera menu.
Something is wrong with the coloring of the pictures. Refer to “Auto tracking white adjustment (ATW)” and switch to “ATW”.
When performing operations from a controller (AW-RP60/AW-RP150).
The unit does not move. – Select the unit to be operated by referring to the operating instructions for the controller. – if the unit’s status display lamp is off or lights up orange, it means that the unit’s power is not on. Refer to “Turn the power on”, and turn on the power. – Check that the account settings for this unit have been set correctly. – Network connection with AW-RP60/AW- RP150 requires setup of an initial account. When an initial account is not set up, AW-RP60/AW-RP150 can detect but cannot control this unit.
Multiple color bands (color bars) are displayed. Switch to the camera image by pressing the button.
Something is wrong with the coloring of the camera pictures. Refer to “Auto tracking white adjustment (ATW)”, and switch to [ATW].
42

Advanced Operations
In the following will description more operations and setting of the camera unit.
Preset Memories
The camera unit enables up to 100 settings for the camera direction (panning and tilting), zoom to be registered in its preset memories, and called. However, the number of settings that can be registered and called depends on the type of wireless remote control or controller that is used for operation. [Note] The recalling of a preset can be performed while the recalling of a preset can be performed while manual operations,
such as pan, tilt, zoom. Nothing will occur if a preset memory number to which a preset has not been registered is recalled. When performing the operations using the wireless remote control Twelve settings (preset No.1 to No.12) can be registered and called using the wireless remote control. The [1] to [12] buttons correspond to the unit’s preset memories No.1 to No.12. Registering the settings in the preset memories 1 Display the picture to be shot on the monitor. Operate the pan, tilt or zoom buttons to determine the camera
view. 2 While holding down the [PRESET] button, press the button corresponding to the preset memory number.
If a preset memory number with an already registered setting has been selected, the existing setting will be erased and replaced with the new one. Calling the settings of the preset memories Press the button in which the preset memory setting has been registered. When performing operations from a controller (AW-RP60/AW-RP150). UP to 100 entries can be registered/recalled. For details, refer to the operating instructions for the controller.
43

Adjust the White Balance
In order for the white to be reproduced accurately, the ratio between the three primary colors (RGB) is adjusted. If the white balance has shifted out of adjustment, not only will the white be reproduced poorly but the color tones of the entire screen will also be degraded. This adjustment must be performed when using the unit for the first time or when the unit has not been used for
a prolonged period. It must be performed when the lighting conditions or brightness has changed. Once the white balance values have been adjusted, their setup procedure will be completed simply by selecting
them using the menus, web settings or by pressing the buttons on the controller; provided that they are going to be used under the same conditions as the ones established when the values were set. There is no need to set it again. Once a new setting is entered, the previous setting will be erased. [Note] For details, refer to “Selecting the Scene Mode” section.
Automatic Adjustment (AWB: AWB A or AWB B)
When performing the operations using the wireless remote control 1. Shoot a white subject (such as a white wall or handkerchief) so that it fills the screen.
Do not shoot shiny or very bright objects. Steps 2 through 6 represent the procedure for selecting the “AWB A” or “AWB B” memory. They need not be taken if a selection has already been made. 2. Select a scene mode by following the procedure in “Selecting the Scene Mode” section.
3. Press the [] or [] button to bring the highlight to “White Balance Mode”. Press the [ ] button to enter White Balance mode menu.
44

4. Press the [] or [] button to change the White Balance Mode to be used to “AWB A” or “AWB B”, and press the [ ] button to confirm the selection. The selected selection will has a mark sign within.
5. Press the [MENU] button for 2 seconds to exit from menu.
6. Press the button. The auto white balance adjustment (AWB) is performed, and the white balance setting is entered.
[Note] The white balance cannot be adjusted when color bars are displayed. Press the [MODE] button to switch to the
camera picture. White balance may not be correctly set if the lighting of the object is too weak. Since the unit has a built-in memory, the set white balance will remain in the memory even if power is turned off.
Therefore, it is not necessary to reset the white balance if the color temperature of those objects remains unchanged. However, it must be reset if the color temperature changes, such as when you move from indoors to outside, or vice versa.
When performing the operations using the controller (AW-RP60/AW-RP150). For details, refer to the operating instructions for the controller.
Auto Tracking White Balance Adjustment (ATW)
When white balance adjustment is set to “ATW”, the white balance will be corrected automatically, even if the light source or color temperature changes.
This function works when “ATW” is selected instead of “AWB A” or “AWB B” by following the steps for “Automatic adjustment” in “Automatic Adjustment (AWB: AWB A or AWB B)” (page 44). [Note] ATW might not function properly when high brightness light (ex. fluorescent lamp) beams into a screen. White balance may not be accurately set if there is no white object in the scene being shot. The white balance may shift out of adjustment when a different kind of light source such as sunlight or fluorescent
lighting applies.
3200K and 5600K Presets
When “3200K” or “5600K” is selected for the white balance, the white balance is set using a color temperature of 3200K (equivalent to halogen light) or 5600K (equivalent to daylight), respectively. This function works when “3200K” or “5600K” is selected instead of “AWB A” or “AWB B” in the “Automatic adjustment” procedure in “Automatic Adjustment (AWB: AWB A or AWB B)”.
45

Menu Operation

Menus are displayed on the monitor when the unit’s settings are to be selected. The monitor is connected to the video signal output connector. The basic camera menu operations involve displaying sub-menus from the main menu items, and selecting settings on the sub-menus. Some sub-menus have menu items for performing more detailed settings. The menu operations are conducted using the wireless remote control.

Described below are the basic operations for changing the camera menu item settings using the wireless remote control.
Only the steps taken using the wireless remote control will be described here for the operations conducted to select and set the items.

Operations Table

Menu operation Selecting the unit to be operated Displaying the main Menu Selecting the items Displaying the sub-menus Returning to the previous menu Changing the settings

Wireless remote control Press the [CAMERA 1], [CAMERA 2], [CAMERA 3] or [CAMERA 4] button. Press the [MENU] button for 2 seconds. Press the [] or [] ([] or []) button. Press the [ ] button. Move the highlight at the “Return” position, press the [ ] button.
With the highlight at the item to be changed, press the [ ] button to select it. Use the [], [], [] and [] buttons to change the value, and press the [ ] button to enter the change.

Canceling the setting change Exiting the menu operations

Press the [MENU] button. Press the [MENU] button for 2 seconds.

[NOTE] When AW-RP60/AW-RP150 is connected, refer to the operating instructions for the controller.

When performing the operations using the wireless remote control
1. Press the [CAMERA 1], [CAMERA 2], [CAMERA 3] or [CAMERA 4] button to select the unit which is to be operated.
2. Press the [MENU] button for 2 seconds. The main menu is displayed.
3. Press the [] or [] button to bring the cursor to the item to be selected. Each time the [] or [] button is pressed, the cursor moves. The cursor can be moved in the same way using the [] and [] buttons.
4. Press the [ ] button. The sub-menu of the selected item is displayed. (Some sub-menu items have a sub-menu of their own.)
5. Press the [] or [] button to bring the cursor to the item to be set. Each time the [] or [] button is pressed, the cursor moves. The cursor can be moved in the same way using the [] and [] buttons. With the cursor at the “Return” position, press the [ ] button to return to the previous menu.

46

6. Press the [ ] button. The value of the item to be selected or confirmed.
7. Press the [] or [] button to change the setting. The setting can be changed in the same way using the [] and [] buttons.
8. Press the [ ] button. The value of the item to be set is entered, and it has a mark sing within.
9. After the setting has been completed, press the [MENU] button for 2 seconds. The menu display is exited.
47

Menu Items
Setting the menu items When the unit’s settings are to be selected, the camera menus are displayed on the monitor. The monitor is connected to the video signal output connector. The basic camera menu operations involve displaying sub-menus from the Top Menu items, and selecting settings on the sub-menus. Some sub-menus have menu items for performing more detailed settings.
Main Menu Screen
Camera Select this to open the camera menu relating to the camera images. System Displays the System menu in which the camera’s output image settings are configured. Maintenance Displays the Maintenance menu which concerns checking the unit’s firmware versions, checking the IP address and initialize the settings. [Note] The main Menu does not have a “Return” setting.
Camera Menu
This menu is for the camera image settings. The functions will be varied by selected “scene” mode (Full Auto, Scene1, and Scene2).
48

Scene
There are three scene modes ­ Full Auto, Scene 1, and Scene 2.
Full Auto: In this mode, for menu items under [Brightness], the optimum settings and adjustments for the shooting conditions at hand are automatically established. But user still can adjust the value of Picture Level, AGC MaxGain, and Slow Shutter.
Scene1 and Scene2: One of two shooting modes (Scene1 and Scene2)–whichever one will best suit the shooting conditions–can be selected. The shooting modes are set by the user.
Factory settings: Full Auto For details of the factory setting, refer to pages 66 to 68.
Picture Level
[-4~4] Adjust the brightness level. Factory settings: 0
AGC MaxGain
[24dB, 30dB, 36dB, 42dB] If you select CAMERA < Scene < Full Auto, you can set up the maximum gain-up amount value. If you select CAMERA < Scene < Scene1/Scene2, when “Auto” is selected as the “Gain” setting, the maximum gain-up amount can be set as (24 dB, 30 dB, 36 dB, 42 dB). Factory settings: 24 dB.
49

Slow Shutter
[Off, On] Set slow shutter function to “On” or “Off”. Factory settings: Off [Note]: This is only enabled when [Scene] is set to [Full Auto].

Iris Mode
[Auto, Manual] You can choose to manually or automatically adjust iris.

Manual The iris is adjusted manually.

Auto

Auto exposure compensation is performed so

that the target level which was set using

[Picture Level] is reached.

Factory settings: Auto

[Note]:

This is only enabled when [Scene] is set to [Scene1] or [Scene2].

Shutter Mode
[Off, Step, Synchro] Factory settings: Off
When “Step” is selected as the “Shutter Mode” [50Hz] 1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000
[59.94Hz/60Hz] 1/1, 1/2, 1/3, 1/7, 1/15, 1/30, 1/60, 1/120, 1/240, 1/480, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000
When “Synchro” is selected as the “Shutter Mode” [59.94p/29.97p] 60.0Hz660.0Hz [50p/25p] 50.0Hz570.1Hz
[Note]: Shutter Mode is only enabled when [Scene] is set to [Scene1] or [Scene2]. The Synchro value can be set up to 255 steps in the above range.

50

Gain
[Auto, 0dB, 3dB, 6dB, 9dB, 12dB, 15dB, 18dB, 21dB, 24dB, 27dB, 30dB, 33dB, 36dB, 39dB, 42dB] In locations which are too dark, adjust the gain upward; conversely, in locations which are too bright, adjust it downward. When “Auto” mode is set, the light quantity is adjusted automatically. The noise increases when the gain is increased. Factory settings: 0
Frame Mix
[Auto, Off, 6dB, 12dB, 18dB, 24dB] Select for frame addition (gain-up using sensor storage) amount. When frame addition is performed, it will appear as if the images are missing some frames. Factory settings: Off [Note]: [Frame Mix] is only enabled when [Shutter Mode] is set to [Off].
Auto F. Mix Max Gain
[0 dB, 6dB, 12dB, 18dB] Sets the maximum amount of frames that can be added when [Frame Mix] is running in [Auto] mode. When frame addition is performed in [Auto] mode, it will appear as if the images are missing some frames. Factory settings: 0
Chroma Level
[0~10] Set the color intensity (Chroma level) of the images, 0-10. Factory settings: 5
51

White Balance Mode
Select the mode when the coloring is not natural because of the nature of the light source or other factors. If the white color serving as the reference can be recognized, subjects can be shot with natural coloring. ATW: This mode automatically corrects the white balance,
even if the light source or color temperature changes. AWB A, AWB B: When AWB A or AWB B is selected and
the white balance is executed, the adjustment results obtained are stored in the memory selected. When AWB A or AWB B is then selected, the white balance stored in the selected memory can be recalled. 3200K: This white balance mode is ideal when a 3200K halogen light is used as the light source. 5600K: This white balance mode is ideal when 5600K sunlight or fluorescent lighting is used as the light source. Factory settings: ATW
R Gain
[­30 ~ +30] This enables the R Gain to be adjusted. Its setting takes effect when [AWB A] or [AWB B] has been selected as the [White Balance Mode] setting. Factory settings: 0
B Gain
[­30 ~ +30] This enables the B Gain to be adjusted. The function takes effect when [AWB A] or [AWB B] has been selected as the [White Balance Mode] setting. Factory settings: 0
Pedestal
[­10 ~ +10] This item is used to adjust the black level (adjust the pedestal). These parts become darker when a negative setting is selected and, conversely, lighter when a positive setting is selected. Factory settings: 0
52

Detail
[0~3] Adjust the sharpness of the image. Factory settings: 2
Contrast
[0~4] Adjust the contrast level of the image. Factory settings: 2
DRS
[Off, On] Set here is the DRS function which provides just the right amount of compensation when images with significant light/dark differences are displayed. Depending on the shooting conditions, however, the picture quality may drop with increased noise. Factory settings: Off
Back Light COMP
[Off, On] Set backlight compensation function to “On” or “Off”. Under backlight conditions, the function prevents darkening as a result of light striking the backs of subjects, and makes it possible to shoot images in shade or shadow more brightly. Factory settings: Off
DNR
[Off, Low, High] Set the level of the digital noise reduction effect so that light, noise-free and clear images will be output even at night and in other low-brightness environments. When “Low” or “High” is selected, noise can be eliminated. However, there is an increased possibility that afterimages may occur. Factory settings: Low
53

System Menu
The following will describe the each function in System menu.
Priority Mode
Configure the setting for the priority output of video. HDMI (4K): 4K video is output to an external monitor
connected via an HDMI cable. USB (4K): Enables the unit to be used as a 4K Web
camera. The camera can also be controlled from a personal computer. IP (4K): Enables IP image transmission. IP image transmission of 4K images uses the H.264/H.265 video coding format. This unit cannot display H.264/H.265 format images on the Live screen.To display H.264/H.265 images, use an external device or external software that supports H.264/H.265 images. HDMI/USB: HD format video is output to an external monitor connected via an HDMI/SDI cable. Enables the unit to be used as a Web camera. The camera can also be controlled from a personal computer. IP: HD format video is output to an external monitor connected via an HDMI/SDI cable. Enables IP image transmission. The IP transmission of H.264/H.265 images is also supported. This unit cannot display H.264/H.265 format images on the Live screen. To display H.264/H.265 images, use an external device or external software that supports H.264/H.265 images. USB (Video Conference): Enables the unit to be used as a Web camera. Specially tuned for online meetings, the unit automatically goes into the Standby mode when an online meeting comes to an end; if an online meeting starts while the unit is in the Standby on mode, the unit automatically switches into the Power ON mode.
Factory settings: HDMI/USB
54

Frequency
[50Hz, 59.94Hz, 60Hz] Set the frame frequency ­ 50Hz, 59.94Hz, or 60Hz. When the frequency is switched, “Format” is set as following:

Frequency
Format HDMI
Format SDI

50Hz
2160/25p 1080/50p 1080/25p 720/50p 1080/50i
1080/50p, 1080/25p, 720/50p
1080/50i

59.94Hz
2160/29.97p 1080/59.94p 1080/29.97p 720/59.94p 1080/59.94i
1080/59.94p, 1080/29.97p, 720/59.94p 1080/59.94i

60Hz
2160/30p 1080/60p 1080/30p 720/60p 1080/60i
1080/60p, 1080/30p, 720/60p
1080/60i

When changing the frequency, select “OK” to confirm the changing.
[Note] When using a monitor that does not support 59.94Hz/50Hz/60Hz frequencies, images may not be displayed after the frequency is changed. Before changing the frequency, verify that your monitor supports that frequency. When Frequency is changed, the unit restarts. Factory settings: 59.94Hz (AW-UE20KP, AW-UE20WP)
50Hz (AW-UE20KE, AW-UE20WE, AW-UE20KED, AW-UE20WED)
55

Format
Change the image format. The image format can different by the frequency.

Frequency
Format HDMI
Format SDI

50Hz
2160/25p 1080/50p 1080/25p 720/50p 1080/50i
1080/50p, 1080/25p, 720/50p
1080/50i

59.94Hz
2160/29.97p 1080/59.94p 1080/29.97p 720/59.94p 1080/59.94i
1080/59.94p, 1080/29.97p, 720/59.94p 1080/59.94i

60Hz
2160/30p 1080/60p 1080/30p 720/60p 1080/60i
1080/60p, 1080/30p, 720/60p 1080/60i

When changing the format, select “OK” to confirm the changing. Finally, select “Yes” to accept the changes.

Factory settings: [50Hz] 1080/50p [59.94Hz] 1080/59.94p [60Hz] 1080/60p
56

Install Position
[Desktop, Hanging] “Desktop” or “Hanging” is selected here as the method used to install the unit. When “Hanging” has been selected, the top, bottom, left and right of the images will be reversed and up/down/left/right control for panning and tilting will also be reversed. Factory settings: Desktop
Preset Speed Table
[Slow, Fast] Set the preset speed table (Slow, Fast). During preset playback, preset actions are performed at Preset Speed (1 to 30) values that are based on the table set here. Factory settings: Fast

Preset Speed
[1~30] Set the pan/tilt operation speed in 30 steps when playing back the preset memory. Factory settings: 20 [Note] If a high value is selected for the Preset Speed setting, the image on the screen may shake when operation stops.

Preset Scope
[Mode A, Mode B, Mode C] Selected here are the setting items to be recalled when the contents of the preset memory are regenerated.

Mode A Mode B Mode C

Pan, Tilt, Zoom (including digital zoom), Focus, Iris, Gain, White Balance Pan, Tilt, Zoom (including digital zoom), Focus, Iris Pan, Tilt, Zoom (including digital zoom), Focus

Factory settings: Mode A

57

Speed with Zoom Position
[Off, On] When [On] is set, if you adjust the zoom in the “Tele” direction, the panning and tilting operations will become slower than usual. This function has no effect during preset operations. Factory settings: On

Focus Mode
[Manual, Auto] “Auto” or “Manual” is set here for the focusing function. Auto: The subjects are always brought into focus automatically. Manual: The focus is operated manually. Factory settings: Auto

Focus Adjust With PTZ
[Off, On] “Off” or “On” is set here for the function which compensates for out-of-focusing when it occurs during panning, tilting or zooming operations at the manual focus setting. This item can be selected only when “Manual” has been selected as the “Focus Mode” setting. Factory settings: Off

Zoom Mode

[Opt.Zoom, i.Zoom, D.Zoom]

Select a zoom mode.

Opt.Zoom Use only the optical zoom. Up to 12× optical

zoom is possible.

i.Zoom

Enabling this function allows you to perform

electronic zoom while reducing drops in picture

quality.

Combining optical zoom and electronic zoom, up

to 15.96× zoom is possible.

D.Zoom: Enable the digital zoom function.

Picture quality degrades as zoom increases with

digital zoom.

Factory settings: Opt.Zoom

58

Max Digital Zoom
[×2, ×3, ×4] Set the maximum digital zoom magnification. This is only enabled when [Zoom Mode] is set to [D.Zoom]. Factory settings: ×4 [Note] Higher digital zoom magnifications will result in coarser images.

Digital Extender
[Off, ×1.4, ×2.0] Make settings for the digital extender function.

Off

Turn the digital extender function off.

×1.4

The digital zoom will be fixed at 1.4×.

×2.0

The digital zoom will be fixed at 2.0×.

Factory settings: Off

Tally
[Enable, Disable] “Enable” or “Disable” is set here for the function which turns on or turns off the tally lamp using the tally control signal. Factory settings: Enable

Status Lamp
[Enable, Disable] [Disable] or [Enable] is set here for the status display lamp. When you want the status display lamp to stay off while this unit is in operation, set to [Disable]. Factory settings: Enable [Note] Even when set to [Disable], the status display lamp may light up when this unit is starting up, updating firmware, or trouble is occurring.

59

Wireless ID
[1, 2, 3, 4] Configure the unit’s remote control ID. The settings for this item correspond to the [CAMERA 1] to [CAMERA 4] buttons on the wireless remote control. Factory settings: 1
OSD off with Tally
[Off, On] “Off” or “On” the function that turns off menu and other displays when red tally signals are received via commands. When the red tally signal releases, the menu display will return. Factory settings: Off
Color Bar
[Off, On] Switch between color bar display and camera image display.
Color Bar
Factory settings: Off [Note] Only HDMI and SDI can output color bar. IP and USB cannot output color bar.
Audio
[Off, On] Enable/disable the audio input signal from the device connected to the audio input connector. Factory settings: Off
60

Input Type

[Mic, Line]

Select an Input Type.

Mic

Set the microphone input.

Line

Set the line input.

Factory settings: Line

This is only enabled when [Audio] is set to [On].

Volume Level
[­36 dB +12 dB] Set the volume of audio output. This is only enabled when [Audio] is set to [On]. Factory settings: 0dB

Plugin Power
[Off, On] Turn the plugin power for the audio off/on. This is only enabled when [Audio] is set to [On]. This is only enabled when [Input Type] is set to [Mic]. Factory settings: Off
Serial Com. Protocol
[Panasonic, Standard] Set the serial communication protocol for the RS422 terminal. You can select either Panasonic or Standard. Factory settings: Panasonic
Connector Select
[RS422, RS232C] You can select either RS422 or RS232C. Factory settings: RS422 This is only enabled when [Serial Com. Protocol] is set to [Standard].

61

Baud Rate
[9600bps, 38400bps] You can select a baud rate for serial communication. Factory settings: 9600bps This is only enabled when [Serial Com. Protocol] is set to [Standard].
Camera Address
[Auto, 1, 2, 3, 4, 5, 6, 7] Should you select Auto, the unit will be assigned with an IP address based on the order you connected the unit. If you select any number from 1 to 7, it will be assigned to the specified camera number. Factory settings: Auto This is only enabled when [Serial Com. Protocol] is set to [Standard] and [Connector Select] is set to [RS232C].
62

Maintenance Menu
Language
[English, , ] The system supports three languages ­ English, Japanese, and Simplified Chinese. Factory settings: English
Firmware Version
Main: Displays the main software version.
Power: Displays the software version of the power.
63

Servo: Displays the software version of the servo.
IP Address
Displays the IP address of the unit.
Subnet Mask
Displays the subnet mask of the unit.
Default Gateway
Displays the default gateway which has been set for the unit.
MAC Address
Displays the MAC address of the unit.
64

Initialize
[Execute, Cancel] You can click [Execute] to initialize the menu items of the unit, except for the settings of [Priority Mode], [Frequency], and [Format].
65

Menu Table

Main menu CAMERA

Sub menu Scene

Factory default setting

Full Auto

Scene1

Scene2

Selection Items Full Auto, Scene1, Scene2

Brightness

Picture Level

0

0

0

-4, -3, -2, -1, 0, +1, +2, +3, +4

AGC Max Gain

24 dB

24 dB

24 dB

24 dB, 30 dB, 36 dB, 42 dB

Slow Shutter

Off

—

—

Off, On

Iris Mode

—

Auto

Auto

Auto, Manual

Shutter Mode
Step
Synchro Gain Frame Mix Auto F.Mix Max Gain

—

Off

Off

Off, Step, Synchro

[50Hz]

1/1, 1/2, 1/3, 1/6, 1/12, 1/25,

1/50, 1/100, 1/250, 1/500,

[50 Hz] [50 Hz]

1/1000, 1/2000, 1/4000,

—

1/50

1/50

1/8000, 1/16000

[59.94 Hz/60 Hz] [59.94 Hz/60 Hz] [59.94Hz/60Hz]

1/60

1/60

1/1, 1/2, 1/3, 1/7, 1/15, 1/30,

1/60, 1/120, 1/240, 1/480,

1/1000, 1/2000, 1/4000,

1/8000, 1/16000

[50 Hz] [50 Hz] [59.94p, 29.97p]

—

50.0 Hz

50.0 Hz

60.0 Hz660.0 Hz

[59.94 Hz/60 Hz] [59.94 Hz/60 Hz] [50p, 25p]

60.0 Hz

60.0 Hz

50.0 Hz570.1 Hz

Auto, 0 dB, 3 dB, 6 dB, 9 dB,

—

0 dB

0 dB

12 dB, 15 dB, 18 dB, 21 dB, 24 dB, 27 dB, 30 dB, 33 dB, 36

dB, 39 dB, 42 dB

—

Off

Off

Auto, Off, 6 dB, 12 dB, 18 dB, 24dB

—

0 dB

0 dB

0 dB, 6 dB, 12 dB, 18 dB

Picture Chroma Level White Balance Mode
R Gain B Gain Pedestal Detail Contrast DRS Back light COMP. DNR

5
ATW
0 0 0 2 2 Off Off Low

010 ATW, AWB A, AWB B,
3200K, 5600K -30+30 -30+30 -10+10 0, 1, 2, 3 0, 1, 2, 3, 4 Off, On Off, On
Off, Low, High

66

Main menu SYSTEM

Sub menu Priority mode

Frequency Format

Install Position Preset Speed Table Preset Speed Preset Scope Speed With Zoom Position Focus Mode Focus Adjust With PTZ. Zoom Mode Max Digital Zoom Digital Extender Tally Status Lamp Wireless ID OSD off with Tally Color Bar Audio Input Type Volume Level Plugin Power Serial Com. Protocol Connector Select Baud Rate Camera Address

Factory default setting HDMI/USB
59.94Hz [50Hz] 1080/50p [59.94Hz] 1080/59.94p [60Hz] 1080/60p
Desktop Fast 20
Mode A On
Auto Off
Opt.Zoom x4 Off
Enable Enable
1 Off Off Off Line 0 dB Off Panasonic RS422 9600 bps Auto
67

Selection Items HDMI (4K), USB (4K), IP (4K), HDMI/USB, USB (Video Conference), IP
50Hz, 59.94Hz, 60Hz [50Hz] 2160/25p, 1080/50p, 1080/25p, 1080/50i, 720/50p [59.94Hz] 2160/29.97p, 1080/59.94p, 1080/29.97p, 1080/59.94i, 720/59.94p [60Hz] 2160/30p, 1080/60p, 1080/30p, 1080/60i, 720/60p
Desktop, Hanging Fast, Slow 130
Mode A, Mode B, Mode C
Off, On
Manual, Auto
Off, On
Opt.Zoom, i.Zoom, D.Zoom x2, x3, x4
Off, x1.4, x2.0 Disable, Enable Disable, Enable
1, 2, 3, 4 Off, On Off, On Off, On Mic, Line -36 dB+12 dB (3 dB step)
Off, On Panasonic, Standard
RS422, RS232C 9600 bps, 38400 bps Auto, 1, 2, 3, 4, 5, 6, 7

Main menu Sub menu MAINTENANCE Language
FW Version Main Power Servo
IP Network IP Address Subnet Mask Default Gateway MAC Address
Initialize

Factory default setting English
Version at shipping
——-
192.168.0.10 255.255.255.0
192.168.0.1 MAC Address of the unit
Execute

Selection Items English, Japanese (), Simplified Chinese ()
—
——-
——–Execute, Cancel

68

Web Screen Start-up

With a personal computer connected to the unit, it is possible to view the camera’s IP videos or select various settings from the web browser.

The LAN crossover cable is used when connecting a personal computer directly to the unit’s LAN connector for IP control, and the LAN straight cable is used when making the connection through a switching hub.

Select an IP address for the personal computer within the private address range while ensuring that it is different from the address of the unit. Set the subnet mask to the same address as the unit.

Unit’s IP address and subnet mask (factory settings)*1

IP address:

192.168.0.10

Subnet mask:

255.255.255.0

*1 The factory default for the private address range is between 192.168.0.1 and 192.168.0.255.

If the controller and web browser are being used at the same time, the content selected using the controller may not be reflected on the web browser display. When using both the controller and web browser, be absolutely sure to check the settings using the controller or menu.
For details of the required personal computer environment, refer to Required Personal Computer Environment.

69

Connecting to Web Screen by Using a PC

The procedure is explained here using Windows screens (Internet Explorer). When using other browsers, some screen displays will be different, but the procedure is similar.

1. Start the web browser of the personal computer. Use one of the web browsers below depending on the operating system installed in the personal computer.

Operating system

Web browser

Windows 10 64bit/32bit Internet Explorer 11 Microsoft Edge Google Chrome

macOS 10.15
macOS 10.14 macOS 10.13 macOS 10.12 OS X 10.11

Safari Google Chrome

2. Enter the IP address you configured on the Easy IP Setup Software in the address bar of the web browser. IPv4 address entry example: http://URL registered with IPv4 address http://192.168.0.10/ IPv6 address entry example: http://[URL registered with IPv6 address] http://[2001:db8::10]/
[Note] If the HTTP port number has been changed from “80”, enter “http://:” in the
address bar. Example: http://192.168.0.11:8080 If the unit is located on the local network, configure proxy server settings on the web browser ([Setup] > [Network])
so that a proxy server is not used for the local address. 3. Display the live screen [Live].
The web screen appears. You can switch to the web setup screen [Setup] when necessary.

[Note] Depending on the firewall settings on your personal computer, transmitted images may not be displayed. If this
occurs, change the firewall settings and change the settings to permit communications with your web browser. When an attempt is made to display multiple IP images on one personal computer, IP videos may not be displayed
depending on the performance of the personal computer concerned. Images on the web screen are displayed in JPEG. The JPEG image frame rate may be slower depending on the network environment, performance of your personal
computer, subject of the video, and access volume.
70

Switching between Live and Setup Screen
When the live screen is displayed, click the [Setup] button. For details on the web setup screen, see “Web Screen Configuration” section. When the web setup screen is displayed, click the [Live] button to switch to live screen. For details on the live screen, see “Web Live Screen Operation” section. [Note] During Standby mode, the [Setup] button is disabled, and you cannot switch to the [Setup] screen. If the unit is switched to Standby mode from another terminal while the [Setup] screen is displayed, the display will
switch to the live screen after a few seconds.
71

Web Live Screen Operation
You can display images from the camera on a personal computer and perform camera operations, such as pan, tilt, and zoom.
(1)
(2) (D)
(3)

(4)

(5)

(6)

(7)

Name (1) Live/Setup (2) RTMP Streaming
(3) OSD Menu Operations

Function
Click [Live] to switch to live screen. Click [Setup] to switch to setup screen. Setup for uploading the camera’s live view to the broadcasting platform. Click [Start] button to start uploading the live image to pre- registered broadcasting platform. When RTMP starting, the start button will turn into stop button. To stop, click [Stop] button To setup RTMP, please refer “RTMP setting” section.
: Use this to select whether the camera’s on- screen displays are to be shown.
The items are selected using the [] [] [] [] buttons. : If a selected item has a sub menu, this sub menu is displayed by
pressing the [OK] button.

: It cancels the selection of the setting which is being changed. It restores
the pre-change setting. [Note] On-screens displays are not displayed on JPEG images on web screens.

72

Name (4) Power (5) Zoom and Focus
(6)

Function
: Set the unit to Power ON mode.
: Set the unit to Standby mode. In the Standby mode, all the buttons on the live screen except for the [Power ON] button and [Standby] button are disabled. [Note] If [Power ON] or [Standby] is selected too quickly, the status selected and the display shown may not correspond. In a case like this, follow the steps below to restore the correct status display: For Windows: Press the [F5] key on the keyboard of the personal computer. For Mac: Press the [Command] + [R] keys on the keyboard of the personal computer. The pan/tilt position return to the place just before entering STANDBY mode when returning from STANDBY mode to POWER ON mode. If the power is turned off, the pan/tilt position returns to the initial state.
: Use this to adjust the zoom (magnification) to 1.0x
: Use this to adjust the zoom (magnification) in the “Tele” direction.
: Use this to adjust the zoom (magnification) in the “Wide” direction.
: Select the speed at which zoom operations are to be performed.

(auto focus)

Click Auto to switch between auto and manual focus. Green Auto indicates that the focus is adjusted automatically. White Auto indicates that the focus is adjusted manually.

(manual focus)

Near Use this to adjust the focus in the Near direction.

It does not work during automatic adjustments.

O.T.AF

When this is pressed while the focus is being adjusted manually, the focus will be temporarily adjusted automatically.

It does not work during automatic adjustments.

Far

Use this to adjust the focus in the Far direction.

It does not work during automatic adjustments.

To adjust the image in the horizontal or vertical direction (panning or tilting), left-click the pad and the buttons. It is possible to operate with the central grid pattern in the dragged state, with the speed of the pan/tilt increasing as it approaches the outside of the pad.

73

Name
(7) Preset and Brightness
[Note] Brightness is only enabled when [Scene] is set to [Scene1] or [Scene2].

Function

(Auto brightness)

Select a preset number or home position from the drop-down list. Click [Move] to go to a previously-configured preset position.

Using

to adjust the unit position and click

[Set] to register the preset position.
Auto Use this to switch the brightness adjustment between auto and manual. Green Auto indicates that the brightness is adjusted automatically. White Auto indicates that the brightness is adjusted manually.

(Manual brightness)

Use this to make the image darker. It does not work during automatic adjustments.

+ Use this to make the image lighter. It does not work during automatic adjustments.
If you click on a part of the area where the live screen image is displayed, pan / tilt will operate so that the clicked position is in the center.

74

Web Screen Configuration
Select the Setup Screen
In live screen, click the [Setup] button to switch to setup screen.

Setup menu

Functions settings area

Power ON/Standby mode switching

75

Basic Settings

From the Setup menu click [Basic] button to display the Basic settings page. In basic settings, user can select [Priority mode], set up name of [Live page], and access [Date & Time].
Selecting Priority Mode
Configure the setting for the priority output of video. Click [Setup] > [Basic] > [Priority Mode] Click [Set] to save the configuration.

HDMI (4K): 4K video is output to an external monitor IP: HD format video is output to an external monitor

connected via an HDMI cable.

connected via an HDMI/SDI cable. Enables IP image

USB (4K): You can use this unit as a 4K Web

transmission. The IP transmission of H.264/H.265

camera. The camera can also be controlled from a

images is also supported. This unit cannot display

personal computer. When the unit is used as a

H.264/H.265 format images on the Live screen. To

4K-compatible Web camera, the frame rate will be

display H.264/H.265 images, use an external device

fixed at 5 fps. IP (4K): Enables IP image transmission. IP image

or external software that supports H.264/H.265 images.

transmission of 4K images uses the H.264/H.265

USB (Video Conference): Enables the unit to be

video coding format. This unit cannot display

used as a Web camera. Specially tuned for online

H.264/H.265 format images on the Live screen.To

meetings, the unit automatically goes into the

display H.264/H.265 images, use an external device

Standby mode when an online meeting comes to an

or external software that supports H.264/H.265

end; if an online meeting starts while the unit is in the

images.

Standby on mode, the unit automatically switches

HDMI/USB: HD format video is output to an external

into the Power On mode.

monitor connected via an HDMI/SDI cable. Enables

In this mode, you cannot output video via HDMI or

the unit to be used as a Web camera. The camera

SDI, and you cannot output video via IP

can also be controlled from a personal computer.

transmission. (Video output will not be possible

except via USB). Also, in this mode, the audio output

is forcibly turned off.

[Note]

When “Priority Mode” is changed, OSD display and IP streaming may not work, as the unit may reconnect to the

RTMP server.

When “Priority Mode” is set to IP (4K), USB (4K) or HDMI (4K), Frame rate of Video is automatically set to

30p/29.97p/25p. Under the USB (Video Conference) mode, in order to minimize the delay of UVC output, HDMI/SDI video output

and video output via IP transmission will be disabled.

76

Live Page (Camera Title)

Input the name of the camera here. Click [Setup] > [Basic] > [Live Page] When the [Set] button is clicked, the input name appears in the camera title display area.

[Note] The factory default setting is the model number of the unit. You can enter between 0 to 20 characters. The following characters can be displayed.

Numeric characters Alphabetical characters (upper and lower cases)
Symbols

0123456789 ABCDEFGHIJKLMNOPQRSTU VWXYZ abcdefghijklmnopqrstuvwxyz #%+=,-_^/@:

77

Date & Time
Click [Setup] > [Basic] > [Date & Time] PC Synchronization If you click the [Execute] button, the settings are configured by synchronizing the unit to the date and time of the connected personal computer. [Note] The time zone of the personal computer is not reflected on the unit. Set the time zone on the unit. NTP If you click [NTP>>], the settings screen for the NTP server appears.( page 104) Manual Date/time Configure the settings for the month, day, and year and for the hour, minute, and second. [Note] · The data display format is MM/DD/YYYY. · The time is in the 24-hour format. Manual Time zone Selects the time zone according to the region where the camera is being used. Factory settings: (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London
78

Image/Audio Setting
Video over IP
Click [Setup] > [Image/Audio] > [Video over IP] The JPEG image and H.264/H.265 image settings as well as the settings related to image quality are selected in here. Click [Setup] > [Image/Audio] > [Video over IP] [Note] IP control can be performed but if you do not want to perform IP image transmission, set [H.264/H.265
transmission] to [Off]. Images and audio are not synchronized. Therefore, images and audio may be slightly out of sync. Please do not change the following menu items during IP streaming: Priority mode, Frequency, Format, Install
Position, Mirror, and Audio. JPEG Set JPEG image settings. Click [Set] to save the configuration. Image capture size
[1280×720, 640×360] Select the resolution for JPEG images. Frame rate [10, 30] Set the frame rate for JPEG images. [Note] When the resolution for Image capture size is 1280×720, the frame rate will be 10 fps.
79

H.264/H.265 Set H.264/H.265 image settings. Click [Set] to save the configuration.
[Note] 1. This is only enabled when Priority Mode is set to “IP (4K) and “IP”. 2. Only JPEG images can be displayed on web screens.
Stream transmission [Off, On] Whether to transmit images is set here. The default is On.
[Note] [Stream transmission] cannot be configured when the Priority Mode selection is anything other than “IP (4K)” or “IP”.

Codec [H.264, H.265] Select the H.264 or H.265 as the image codec.
Image capture size [640×360, 1280×720, 1920×1080, 3840×2160] Select the resolution for H.264/H.265 images.

Frame rate [5fps, 10fps, 15fps, 25fps, 30fps, 50fps, 60fps]

Set the frame rate for H.264 /H.265 images.

50Hz

5fps, 10fps, 25fps1, 50fps2

59.94Hz/60Hz 5fps, 15fps, 30fps1, 60fps2

[Note]:

*1 During RTMP transmission, if you choose [3840 x 2160] for Image Capture Size, the selected frame rate may not

be obtained.

*2 not supported when the Priority Mode is set to [IP (4K)].

Max bit rate (per client) [1024kbps, 1536kbps, 2048kbps, 3072kbps, 4096kbps, 6144kbps, 8192kbps, 10240kbps, 12288kbps, 14336kbps, 16384kbps, 20480kbps, 24576kbps, 32768kbps] Specify the H.264/H.265 bit rate. The default is 14336kbps. [Note] When bit rate is set higher than 8192kbps, the bit rate during RTMPS transmission will be 8192kbps.

80

Audio
Click [Setup] > [Image/Audio] > [Audio] Click [Set] to enable the configuration.
Audio Audio
[Off, On] Select On or Off to enable or disable audio. [Note] 1. If you switch audio On or Off during IP streaming, audio skipping might occur. 2. When Audio is On, RTMP transmission may not start. (Such an occasion arises when the server to which RTMP
transmission is delivered requires audio transmission) 3. If you change Audio from On to Off during RTMP transmission, RTMP transmission may stop. Input Type [Mic, Line] Mic Set the microphone input. Line Set the line input. Volume Level [­36 dB +12 dB] Set the volume level of audio output. This is only enabled when [Audio] is set to [On]. Plugin Power [Off, On] Turn the plugin power for the audio off/on. This is only enabled when [Audio] is set to [On].
81

Image
Image adjustment and preset position setup. Click [Setup] > [Image/Audio] > [Image] 82

Image Adjust Click [Setup] button to call out image adjust dialog. Click [Close] button to exit from image adjust dialog. The image mode has three types ­ Full Auto, Scene1, and Scene2. The dialogue screen may vary depending on which scene mode you select out of the three (Full Auto, Scene1, and Scene2). [Note] Setting data are reflected immediately as soon as they are changed.

Scene: Full Auto

Scene: Scene1/Scene2

83

Picture Level [-4~4] Adjust the picture quality. Move the scroll bar to adjust the value. Factory settings: 0

Iris Mode

[Auto, Manual]

This menu item is used to select whether the iris is to be adjusted automatically or manually.

Manual The iris is adjusted manually.

Auto

Auto exposure compensation is performed so that the target level which was set using [Picture Level]

is reached.

Factory settings: Auto

Shutter mode [Off, Step, Synchro]

Off

The shutter is set to OFF.

Step

The step shutter is set (the steps can be changed).

Synchro The synchro shutter is set (the setting can be changed continuously).

Step/Synchro This is used to adjust the shutter speed in the mode which was selected as the [Shutter Mode] setting. When a higher shutter speed is selected, fast-moving subjects do not become blurred easily but the images will be darker. The shutter speeds that can be set are listed below. When “Step” is selected as the “Shutter Mode”

[50Hz] 1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000 [59.94Hz/60Hz] 1/1, 1/2, 1/3, 1/7, 1/15, 1/30, 1/60, 1/120, 1/240, 1/480, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000

When “Synchro” is selected as the “Shutter Mode”

[59.94p/29.97p] 60.0Hz660.0Hz [50p/25p] 50.0Hz570.1Hz

Factory settings: Off

84

Slow Shutter [Off, On] Set slow shutter function to “Off” or “On”. When Slow Shutter is set to On [50 Hz] 1/1, 1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000 [59.94 Hz/60 Hz] 1/1, 1/2, 1/3, 1/7, 1/15, 1/30, 1/60, 1/120, 1/240, 1/480, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000
When Slow Shutter is set to Off [50 Hz] 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000 [59.94 Hz/60 Hz] 1/60, 1/120, 1/240, 1/480, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000
Factory settings: Off This can only be configured when “Scene” is set to “Full Auto.”
Gain [Auto, 0 dB, 3 dB, 6 dB, 12 dB, 15 dB, 18 dB, 21 dB, 24 dB, 27 dB, 30 dB, 33 dB, 36 dB, 39 dB, 42 dB] In locations which are too dark, adjust the gain upward; conversely, in locations which are too bright, adjust it downward. When “Full Auto” mode is set, the light quantity is adjusted automatically. The noise increases when the gain is increased. Factory settings: 0
AGC Max Gain [24 dB, 30 dB, 36 dB, 42 dB] Set up the maximum gain-up amount value. Factory settings: 24 dB
Frame Mix [Auto, Off, 6 dB, 12 dB, 18 dB, 24 dB] Select for frame addition (gain-up using sensor storage) amount. When frame addition is performed, it will appear as if the images are missing some frames. Factory settings: Off [Note] Under discharge tube illumination, such as fluorescent and mercury- vapor lights, the brightness may change cyclically, colors may change, and horizontal stripes may flow up and down the image.
Auto F.Mix Max Gain [0 dB, 6 dB, 12 dB, 18 dB] Sets the maximum amount of frames that can be added when [Frame Mix] is running in [Auto] mode. When frame addition is performed in [Auto] mode, it will appear as if the images are missing some frames. Factory settings: 0
Chroma Level [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10] Set the color intensity (Chroma level) of the images. Move the scroll bar to adjust the value. Factory settings: 5
85

White Balance Mode [ATW, AWB A, AWB B, 3200K, 5600K] Select the mode when the coloring is not natural because of the nature of the light source or other factors. If the white color serving as the reference can be recognized, subjects can be shot with natural coloring. Click [Execute] button to apply the setting. Factory settings: ATW.
ATW: This mode automatically corrects the white balance, even if the light source or color temperature changes. AWB A, AWB B : When AWB A or AWB B is selected and the white balance is executed, the adjustment results
obtained are stored in the memory selected. When AWB A or AWB B is then selected, the white balance stored in the selected memory can be recalled. 3200K: This white balance mode is ideal when a 3200K halogen light is used as the light source. 5600K: This white balance mode is ideal when 5600K sunlight or fluorescent lighting is used as the light source.
Pedestal [­10 +10] This item is used to adjust the black level (adjust the pedestal). These parts become darker when a negative setting is selected and, conversely, lighter when a positive setting is selected. Factory settings: 0
Detail [0, 1, 2, 3] Adjust the sharpness of the image. Move the scroll bar to adjust the value. Factory settings: 2
Contrast [0, 1, 2, 3, 4] Adjust the Contrast level. Factory settings: 2
DRS [Off, Low, High] Set here is the DRS function which provides just the right amount of compensation when images with significant light/dark differences are displayed. Depending on the shooting conditions, however, the picture quality may drop with increased noise. Factory settings: Off
Back Light COMP [Off, On] Set backlight compensation function to “On” or “Off”. Under backlight conditions, the function prevents darkening as a result of light striking the backs of subjects, and makes it possible to shoot images in shade or shadow more brightly. Factory settings: Off
DNR [Off, Low, High] Set the level of the digital noise reduction effect so that light, noise-free and clear images will be output even at night and in other low-brightness environments. When “Low” or “High” is selected, noise can be eliminated. However, there is an increased possibility that afterimages may occur. Factory settings: Low
86

Preset Position Click [Setup] button to call out preset position dialog. Click [Close] button to exit from image adjust dialog.

Select the preset number or home position from drop-down list. Click [Move] to go to the pre-set position.

Using

to adjust the unit position and click [Set] to register the

preset position. To adjust the image in the horizontal or vertical direction (panning or tilting), left-click the pad and the buttons. It is possible to operate with the central grid pattern in the dragged state, with the speed of the pan/tilt increasing as it approaches the outside of the pad.
: Use this to adjust the zoom (magnification) to 1.0x
: Use this to adjust the zoom (magnification) in the “Tele” direction.
: Use this to adjust the zoom (magnification) in the “Wide” direction.
Select the speed at which zoom operations are to be performed.

Click Auto to switch between auto and manual focus. Green Auto indicates that the focus is adjusted automatically. White Auto indicates that the focus is adjusted manually. Click Near to adjust the focus in the Near direction. It does not work during automatic adjustments. Click O.T.AF while the focus is being adjusted manually, the focus will be temporarily adjusted automatically. It does not work during automatic adjustments. Click Far to adjust the focus in the Far direction. It does not work during automatic adjustments. Click Auto to switch between auto and manual adjustment of the brightness. Green Auto indicates that the brightness will be adjusted automatically. White Auto indicates that the brightness can be adjusted manually. This is only enabled only when [Scene1] or [Scene2] has been selected as the [Priority Mode] setting.
87

Speed with zoom POS. [Off, On] When [On] is set, if you adjust the zoom in the “Tele” direction, the panning and tilting operations will become slower than usual. This function has no effect during preset operations. Factory settings: On
Focus ADJ with PTZ. [Off, On] “Off” or “On” is set here for the function which compensates for out-of-focusing when it occurs during panning, tilting or zooming operations at the manual focus setting. This item can be selected only when “Manual” has been selected as the “Focus Mode” setting. This is only enabled when manual focus has been selected. Factory settings: Off
Preset Setting
Preset speed table [Slow, Fast] Set the preset speed table (Slow, Fast). During preset playback, preset actions are performed at Preset Speed (1 to 30) values that are based on the table set here. Slow: Set the preset speed table to “Slow”. Fast: Set the preset speed table to “Fast”. Factory settings: Fast Preset speed [1~30] There are 30 preset pan-tilt operation speeds when regenerating the camera direction and other information which are registered in the preset memory. Setting range: 1 to 30 [Note] If a high value is selected for the Preset Speed setting, the image on the screen may shake when operation stops. Factory settings: 20
88

Preset scope [Mode A, Mode B, Mode C] Selected here are the setting items to be recalled when the contents of the preset memory are regenerated.
Mode A Pan, Tilt, Zoom (including digital zoom), Focus, Iris, Gain, white balance adjustment value Mode B Pan, Tilt, Zoom (including digital zoom), Focus, Iris Mode C Pan, Tilt, Zoom (including digital zoom), Focus [Note] When registering a preset position, all values are saved. When recalling a registered preset position, there are certain operation procedures to undergo beforehand so that each value can come into effect: [Focus] Firstly, enable manual focus. Then, the focus value of the recalled preset position can come into effect. [Iris] Firstly, enable manual iris. Then, the iris value of the recalled preset position can come into effect. [Gain] Firstly, set Gain between 0 dB~42 dB. Then, the Gain value of the recalled preset position can come into effect. [White Balance Mode] Firstly, set White Balance Mode as AWB A or AWB B. Then, the White Balance Mode value of the recalled preset position can come into effect. Factory settings: Mode A
89

Limitation Setting

This establishes the up, down, left and right limit settings of the pan-tilt head.

First, move the pan-tilt head to the desired limit position using the control pad and its buttons.

When the position is determined, select the desired “Set” setting from the list of settings below to set the position.

(Select “Release” to release the setting.)

Tilt Up

Use this to save the current position as the upward limit.

Tilt Down Use this to save the current position as the downward limit.

Pan Left Use this to save the current position as the leftward limit.

Pan Right Use this to save the current position as the rightward limit.

When “Set” or “Release” is selected, the tally lamp of the unit blinks.

When a limiter is set, it blinks red once; when a limiter is released, it blinks red twice.

90

System Settings
Click [Setup] > [Image/Audio] > [System]

Output

Click [Set] button to save the configuration.

Format

Change the image format. The image format can different by the frequency

Frequency

50Hz

59.94Hz

Format HDMI

2160/25p 1080/50p 1080/25p 720/50p 1080/50i

2160/29.97p 1080/59.94p 1080/29.97p 720/59.94p 1080/59.94i

Format SDI

1080/50p, 1080/25p, 720/50p
1080/50i

1080/59.94p, 1080/29.97p, 720/59.94p 1080/59.94i

60Hz
2160/30p 1080/60p 1080/30p 720/60p 1080/60i
1080/60p, 1080/30p, 720/60p
1080/60i

Factory settings: [50Hz] 1080/50p [59.94Hz] 1080/59.94p [60Hz] 1080/60p

91

Frequency

Set the frame frequency ­ 50Hz, 59.94Hz, or 60Hz.

When the frequency is switched, “Format” is set as following:

Frequency

50Hz

59.94Hz

2160/25p

2160/29.97p

Format HDMI

1080/50p 1080/25p 720/50p

1080/59.94p 1080/29.97p 720/59.94p

1080/50i

1080/59.94i

Format SDI

1080/50p, 1080/25p, 720/50p
1080/50i

1080/59.94p, 1080/29.97p, 720/59.94p 1080/59.94i

60Hz 2160/30p 1080/60p 1080/30p 720/60p 1080/60i
1080/60p, 1080/30p, 720/60p
1080/60i

Factory settings: 59.94Hz
Others
Click [Set] button to save the configuration

Install Position [Desktop, Hanging] “Desktop” or “Hanging” is selected here as the method used to install the unit. When “Hanging” has been selected, the top, bottom, left and right of the images will be reversed and up/down/left/right control for panning and tilting will also be reversed. Factory settings: Desktop
Preset speed table [Slow, Fast] Set the preset speed table (Slow, Fast). During preset playback, preset actions are performed at Preset Speed (1 to 30) values that are based on the table set here. Slow: Set the preset speed table to “Slow”. Fast: Set the preset speed table to “Fast”. Factory settings: Fast
Preset speed [1~30] There are 30 preset pan-tilt operation speeds when regenerating the camera direction and other information which are registered in the preset memory.
[Note] If a high value is selected for the Preset Speed setting, the image on the screen may shake when operation stops. Factory settings: 20

92

Preset scope
[Mode A, Mode B, Mode C] Selected here are the setting items to be recalled when the contents of the preset memory are regenerated.
Mode A Pan, Tilt, Zoom (including digital zoom), Focus, Iris, Gain, white balance adjustment value
Mode B Pan, Tilt, Zoom (including digital zoom), Focus, Iris
Mode C Pan, Tilt, Zoom (including digital zoom), Focus
[Note] When registering a preset position, all values are saved. When recalling a registered preset position, there are certain operation procedures to undergo beforehand so
that each value can come into effect: [Focus] Firstly, enable manual focus. Then, the focus value of the recalled preset position can come into effect. [Iris] Firstly, enable manual iris. Then, the iris value of the recalled preset position can come into effect. [Gain] Firstly, set Gain between 0 dB42 dB. Then, the Gain value of the recalled preset position can come into effect. [White Balance Mode] Firstly, set White Balance Mode as AWB A or AWB B. Then, the White Balance Mode value of the recalled preset position can come into effect. Factory settings: Mode A

Zoom Mode

[Opt.Zoom, i.Zoom, D.Zoom]

Configure the maximum zoom magnification.

Opt.Zoom Use only the optical zoom. Up to 12× optical zoom is possible.

i.Zoom

Enabling this function allows you to perform electronic zoom while reducing drops in picture

quality.

Combining optical zoom and electronic zoom, up to 15.96× zoom is possible.

D.Zoom Enable the digital zoom function.

Picture quality degrades as zoom increases with digital zoom.

Factory settings: Opt.Zoom

Max Digital Zoom [×2, ×3, ×4] Set the maximum digital zoom magnification. This is only enabled when [Zoom Mode] is set to [D.Zoom]. [Note] Higher digital zoom magnifications will result in coarser images. Factory settings: ×4
Digital Extender [Off, ×1.4, ×2.0] Make settings for the digital extender function.
Off Turn the digital extender function off. ×1.4 The digital zoom will be fixed at 1.4×. ×2.0 The digital zoom will be fixed at 2.0×.
This is only enabled when [Zoom Mode] is set to [Opt.Zoom]. Factory settings: Off

93

Speed with zoom POS. [Off, On] When [On] is set, if you adjust the zoom in the “Tele” direction, the panning and tilting operations will become slower than usual. Factory settings: On
Focus mode [Manual, Auto] “Auto” or “Manual” is set here for the focusing function. Setting value:
Auto The subjects are always brought into focus automatically. Manual The focus is operated manually. Factory settings: Auto
Focus ADJ with PTZ [Off, On] “Off” or “On” is set here for the function which compensates for out-of-focusing when it occurs during panning, tilting
or zooming operations at the manual focus setting. This item can be selected only when “Manual” has been selected as the “Focus Mode” setting. Factory settings: Off
Tally [Enable, Disable] “Enable” or “Disable” is set here for the function which turns on or turns off the tally lamp using the tally control signal. Factory settings: Enable
94

Status lamp [Enable, Disable] [Disable] or [Enable] is set here for the status display lamp. When you want the status display lamp to stay off while this unit is in operation, set to [Disable]. Factory settings: Enable [Note] Even when set to [Disable], the status display lamp may light up when this unit is starting up, updating firmware, or trouble is occurring.
OSD off with Tally [Off, On] This is used to enable or disable the function for clearing the OSD menu displays when the tally signal is received by a command or contact. When the tally signal is released, the

References

• O.T.AF
• パナソニック コネクト株式会社 | 企業とビジネス情報
• パナソニック コネクト株式会社

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>