Lucci 018380 Campari 1 Light Pendant Instruction Manual

Lucci 018380 Campari 1 Light Pendant

Product Information

The CAMPARI 1 LIGHT PENDANT is a stylish indoor luminaire suitable for use in residential and commercial spaces. It is available in two color options: BLACK / GREEN MARBLE / BRONZE FINISH and WHITE / WHITE MARBLE / BRASS FINISH. The luminaire has a rated voltage of 220-240V~ 50Hz and a maximum wattage of 45W. It features an ES / E27 lamp holder and weighs 1.7kg. The canopy size is H:90mm D:120mm, and the overall dimensions of the luminaire are H:215mm D:380mm Susp:1800mm.

Installation Instructions

1. Remove all packaging material from the product and lay the luminaire on a smooth non-scratch surface.
2. Feed the cord of the luminaire through the marble finial (K) and install it onto the body (L) of the luminaire.
3. Choose the suspension length by installing different sections of suspension rods (G,H,I,J) onto the body (L) of the luminaire. Feed the cord through as you assemble to remove any slack.
4. Pull the cord of the luminaire up into the canopy (E) and attach the canopy to the top of the suspension rod.
5. Install the figure 8 shape cord anchorage onto the cord of the luminaire inside the canopy, leaving enough room for connection to the terminal block (D).
6. Remove the mounting bracket (B) from the canopy (E) and use it as a template to mark the screw positions on the ceiling.
7. Install the mounting bracket (B) onto the ceiling using appropriately sized mounting screws (C) and anchors (A) suitable for the mounting surface and surrounding environment.
8. Connect the mains supply wire to the terminal block (D), ensuring secure connections and no exposed bare wires.
9. Install the canopy (E) onto the mounting bracket (B) and secure it by tightening the screws (F) on the side.
10. Install a compatible globe (M – not included) into the lamp holder, making sure not to exceed the maximum wattage rating.
11. After installation, switch on the luminaire to test and enjoy your new lighting product.
    Note: The luminaire is a Class I product and must be earthed during wiring and installation.

To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.

Warranty

•  This luminaire is covered by a 12 months warranty. The warranty is from date of purchase, not the date of installation.
• If the luminaire is not assembled and installed by a licensed electrician the warranty will be void.
• Please retain proof of purchase and evidence of installation by a licensed electrician.
• Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.

Installation requirements

• This luminaire must be assembled and installed by a licensed electrician.

• All wiring and installation of the luminaire must adhere to latest local and national wiring rules.
  eg. AS/NZS 3000 Electrical installations.

•  This luminaire is a Class I product and must be earthed during wiring and installation.

• Do not exceed the maximum wattage rating.

•  Select a suitable location for installation:

  • This luminaire is suitable for indoor use only.
  •  The mounting point must support 2 times the weight of the luminaire.
  •  Ensure the luminaire is not installed in direct line of an air vent/system.
  • If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.

• Take care not to pull any electrical wires during unpacking as this may damage the connection.

•  Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.

• Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.

• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. To help with assembly, lay the luminaire on its side on a smooth non scratch surface.
2. Feed the cord of luminaire though the marble finial (K), and install onto the body (L) of luminaire.
3.  Decide on the suspension length of your pendant by installing the different sections of suspension rods (G,H,I,J) onto the body (L) of your luminaire. Feed the cord of luminaire through as you assemble to remove any slack. Take care not to cross thread the suspension rods or twist and damage the cord of luminaire.
4. Pull the cord of luminaire up into the canopy (E) and attach the canopy (E) to the top of the suspension rod.
5. Install the “figure 8” shape cord anchorage onto the cord of luminaire inside the canopy. Ensure to leave enough room for connection to the terminal block (D).
6. Remove the mounting bracket (B) from the canopy (E) by loosening the screws (F) on the sides.
7. Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.
8.  Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (C) and anchors (A). Ensure the screws (C) and anchors (A) used are suitable for the mounting surface and the surrounding environment.
9. Connect the mains supply wire to the terminal block (D) provided. Ensure that the wires are secure and no bare wires are exposed.

NOTE: The luminaire is a Class I product and must be earthed during wiring and installation

10. Install the canopy (E) onto the mounting bracket (B) and secure by tightening the screws(F) on the side.
11. Install a globe (M – not included) into the lamp holder. Do not exceed the maximum wattage rating.
12. After the installation, switch on the luminaire to test and enjoy your new lighting product.

Safety tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
•  To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
•  Select a suitable location away from liquids and hazards.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
• To clean, wipe with a damp clean cloth. Do NOT soak or immerse the product in water or other liquids.

Specifications

FINISH
Rated Voltage| 220-240V~ 50Hz

Rated Wattage

|

45W Max.

Lamp Holder| ES / E27
Weight| 1.7kg
Canopy size| H:90mm    D:120mm
Dimensions| H:215mm    D:380mm    Susp:1800mm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>