ALTEC LANSING MZX5001 AL Nanobuds 3.0 True Wireless Earbuds User Guide
- June 12, 2024
- Altec Lansing
Table of Contents
ALTEC LANSING MZX5001 AL Nanobuds 3.0 True Wireless Earbuds
Product Information
The product is a pair of Wireless Earbuds that come with a voice assistant
feature.
It is designed for use with smartphones equipped with a voice assistant.
The earbuds come with a charging case and have Bluetooth connectivity.
Features:
- Wireless earbuds with voice assistant
- Charging case
- Bluetooth connectivity
Product Usage Instructions
- For the first use, follow these steps:
- Remove the earbuds from the case.
- Remove the sticker from both earbud charging contacts.
- Place the earbuds back in the case.
- Remove the earbuds from the case again. This will activate the earbuds.
- To use the voice assistant feature, make sure you have a phone that is equipped with a voice assistant.
- Ensure that you are within Bluetooth range to use the voice assistant via your Wireless Earbuds.
- The voice assistant feature will not work if a voice assistant is not first enabled within the settings on your phone. Refer to your phone’s user manual for more information on enabling the voice assistant.
- Do Not Return the Card
IMPORTANT
- PLEASE DO NOT RETURN TO THE STORE
- If You’re Having Trouble, We’re Here to Help!
- Thank you for purchasing an Altec
- Lansing product. Download our App to unlock all the features our products have to offer!
In the Box
A Closer Look
Charging
- Ice the earbuds into the case to charge:
- Charging (indicator breathing red every 35)
- Fully charged (indicator breathing blue every 3S)
- The LEDs turn off after about 60S to conserve power
The LED indicator will flash when charging:
- Connect the USB-C cable to the charging port to charge the case.
- The case’s indicator will flash momentarily to indicate low battery.
Powering On
- For the first use, please remove the earbuds from the case and remove the sticker from both earbud charging contacts.
- Next, place the earbuds back in the case then remove them from the case.
- This will activate earbuds.
- To turn them on, place earbuds into the case then remove them from the case. To turn off, place the earbuds into the case.
- If the LEDs do not turn on when the earbuds are removed from the case, charge the case then try again. In the event that the earbuds do not pair together, perform the Manual Reset function.
REGISTER YOUR PRODUCT
- To receive news, exclusive deals, OTA or firmware updates, warranty information, and more please register your product at alteclansingsupport.com
12-Month Limited Warranty
- All Altec Lansing products come with a 12-month limited warranty from the date of their original purchase
24-Hour Customer Support
- We love our customers, and we care about vour experience with Altec
- Lansing. If you need assistance, please call us at 1.855.292.4087 or e-mail [email protected] at www.alteclansing.com
- Altec Lansing Edison, NJ 08817
Bluetooth Pairing
- The AL Nanobuds 3.0 have automatic pairing technology.
- Once removed from the case, they will automatically turn on and pair with each other within a few seconds.
- After the earbuds have paired to each other, to connect the earbuds to your smartphone, go to settings then select the
- Bluetooth page. Look under ‘available devices’ and connect to “AL Nanobuds 3.0”
Touch Button Functions
- Low Latency Mode reduces intrinsic Bluetooth delay for better lip-sync.
- Answering a second call will put the first on hold. When on hold triple press L or R to switch calls.
Bluetooth Multipoint (two devices at once.)
- To connect a second device turn off Bluetooth on the first connected device. Now connect your second device. Turn Bluetooth back on the first device, Nanobuds 3.0 will reconnect to the first device and both will be connected.
Manual Reset
Placing the earbuds back into the case and taking them back out again always
resets the earbuds whilst not losing any pairing information.
In the unlikely event that you need to fully reset the earbuds and clear their
pairing information you can do a Hard reset as follows:
Hard Reset
- Forget the earphones in your phone (important).
- Take ONE earbud out of the case. If the LED is flashing purple wait for it to go red/blue/red/blue. Now Press and Hold the earbud touch button for 12S. The LED will change to Red for 5S, then flash Red three times and the earbud will reset.
- Put it back in the case and do the same operation for the other one.
- Finally, take them both out together, the earbuds will flash purple while they look for each other. Then when they pair together the Primary will go Red/Blue/Red/Blue (the Secondary LED will turn off).
- The earphones are now ready to pair with your phone.
- Reconnect the earbuds to your phone. You should see them in your phones pairing lis as AL Nanobuds 3.0.
Notes
- To use a voice assistant, you must have a phone that is equipped with a voice assistant.
- You must be within Bluetooth range to use voice assistant via your Wireless Earbuds.
- Your Wireless Earbud’s voice assistant feature will not work if a voice assistant is not first enabled within the settings on the phone. For more information, see your phone’s user manual.
- For additional user materials and warranty information, please visit alteclansing.com
FCC
ID: 2ALN9-TW91AL5
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.