Serenity SERLH1300 Left Hand Walk In Bath with Panel and Seat Installation Guide
- June 12, 2024
- Serenity
Table of Contents
Serenity 660 & 750 Installation Guide.
SERLH1300 Left Hand Walk In Bath with Panel and Seat
The Serenity supplied pre-assembled with LH or RH Door Hinging. Fitted 1 x End
Panel, 2 x Hand Grips and 1 x Pop-Up.
Waste/Overflow with a 2″ Horizontal Drain.
Supplied Loose: Pop-Up Plug with Safety Chain. A Reducer Connector & In-Line
Waste Trap for the Horizontal 2″ Drain.
See drawing below.
- DIMENSIONS FOR THE 750 BATH ARE SHOWN IN BRACKETS *
IMPORTANT NOTES
The Serenity is supplied partly assembled. It has no front panel as its front
face is moulded into the bath. 2 x access panels are fitted on either side of
the door for access to the services. An end panel, a pop-up waste with a 2″
horizontal drain and 2 x handgrips are also supplied fitted.
The bath is supplied levelled up on 8 x adjustable feet. The feet have been
raised up to increase the height of the bath from 950 to 980. This leaves a
gap of nominally 30mm at the bottom of the bath, which may require an edging
strip to cover. Height of the bath will need to be readjusted to suit the site
conditions. For easier access the bath door can be removed by unscrewing the 6
screws to the hinges on the bath using a 5mm Allen key and 2 men to hold.
Installation is similar as for a standard bath except that the 2″ diameter
waste has horizontal drain to increase drainage rate. Consequently an In-
LineWaste-Trap will be required. The floor should be sound enough to takethe
weight (65 kilos for the 660 & 74 kilos forthe 750 bath -unfilled) of the
bath without causing any
movement or sagging.
It has water capacity of 285 litres (unoccupied) which may require pump
assisted taps with a flow rate of 17 litres/min minimum. Use only 22mm pipe
leads to enhance flow rate. Bath is filled only when user has entered and shut
door, consequently taps must be thermostatically controlled.
Standard Fitting Guide. See Drawings
-
Remove the 2 x Access Panels on the front of the bath and the End Panel.
-
If bath is to pass through an opening wider than 660mm then carefully remove the door off its hinges on the bath side and refit once positioned.
-
Drill and affix Taps to the bath. Secure the 2″ connector to the horizontal drain outlet on waste.
-
Fit a shallow In-Line-Waste-Trap to the 2″ connector.
-
Place bath in position and lower the bath height such that the bottom of the front edge of the bath is almost touching the floor.
Important: If installing on wooden floor, consideration must be given to re-enforcing the floor and possibly fixing batten wood runs across to support the bath load. Concrete floors must be level so that the bath feet sit flat. -
Level bath in all planes using the 4 adjustable feet on the 4 outer corners only and lock the feet. Screw out the 4 centre support legs firmly to the floor.
-
Mark fixings and plumbing runs.
-
Remove bath and run all plumbing into position. Note: flexible waste and tap pipes will ease the installation.
-
Re-position bath and screw to the floor using all 8 bath feet. Note: the wide feet have no screw holes and can easily be drilled through.
-
Connect plumbing. Refer to fitting guides for the Thermostatic valve and Pump if supplied.
-
Test plumbing for leaks and pump operation.
-
Locate the Pop-Up Waste plug and adjust the stem lock nut and position into the waste.
Test when the bath is filled and adjust again if necessary.
Attach the safety chain on the Pop-Up Waste Plug to the Overflow brass stem -
Refit the access and side panels.
-
Silicone bath rims to walls as necessary and fit a suitable edging strip to bottom of the bath if required.
-
Finally drain bath and Leave the Door Open when in use to prevent over compression and the wear out of the seal.
-
Instruct customer on the use of the bath.
- Refer to ‘Operating/Care and Maintenance Instructions’ and leave copy with customer.
- Do not leave door in locked position on completion. Advise customer that the door should be left unlocked when not in use in order to preserve the seal.
To remove Access and End Panels
Fixing Safety Chain to Pop-Up Overflow
Waste Trap Fixing to Pop-Up Horizontal Drain (52mm ID)
A = overflow hose
B = pop-up horizontal drain -52mm
C = push fit connector – reducer 52mm to 1.5in
D = horizontal waste trap must be installed the right way up ( with the rubber
membrane horizontal) – see instructions
The bath is supplied with its feet adjusted making the height of the bath
980mm (from the floor) – giving a space of 110mm from the underside of the
bath well to the floor. This in turn leaves a gap of 30mm from the lower edges
of the bath to the floor.
The bath feet can be lowered to take up some of the gap, reducing the space
under the bath well from 110 to just under 80mm.
Nov 2018
Documents / Resources
|
Serenity SERLH1300 Left Hand Walk In Bath with Panel and
Seat
[pdf] Installation Guide
SERLH1300 Left Hand Walk In Bath with Panel and Seat, SERLH1300, Left Hand
Walk In Bath with Panel and Seat, Bath with Panel and Seat, Panel and Seat
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>