PAL LIGHTING PCR-1Z-SM Multi-Color Dual Zone Remote Control Transformer Instructions

PAL PCR-1Z-SM Multi-Color Dual Zone Remote Control Transformer

Product Information

The PCR-1Z-SM / PCR-1Z / PCR-2Z Lighting Controller is a device used to control lighting systems. It is designed to supply 24V DC power to PAL 4 Wire UL Listed LED Pool lights. The controller must be installed in accordance with the National Electrical Code by a Certified Electrician or Qualified Pool Technician. It is important to note that no bonding is required from this Class 2 power supply to the UL Listed PAL Pool Light fixtures as they are made of an all plastic construction and comply with NEC article 680 requirements.

Dimensions

• 13/16 / 21.0mm Knockout to connect power supply (2 available on each side of enclosure).
• 3 x conduit holes.
• 6 x conduit holes.

Product Usage Instructions

Knockout Instructions:

1. It is recommended to fit the cover and tighten the cover screws when removing the knockouts.
2. To remove the knockouts, place a flat blade screwdriver with a 3/16 (4mm) blade as shown and lightly hit it with a hammer to the head of the screwdriver.
3.  Alternatively, drill location points are located in the center of each knockout to allow the use of a hole saw to remove the knockouts.

Installation Instructions for PCR-1Z-SM / PCR-1Z / PCR-2Z:

1. Install the PCR-1Z-SM / PCR-1Z / PCR-2Z Lighting Controller in accordance with the National Electrical Code by a Certified Electrician or Qualified Pool Technician.
2. The Driver Enclosure must be located a minimum distance of 5 feet measured horizontally from the inside wall of the pool and not less than 1 foot above the maximum pool water level measured to the top of the Driver Enclosure.
3. Mount the enclosure using the mounting legs and screw set supplied. If mounting on a concrete or block wall, mark out the hole locations, drill 3/16-inch holes using a masonry drill, and fit the Star Plugs supplied into the holes. Secure with the stainless steel screws supplied.
4. Connect the 100-120V power supply to the bottom-right conduit entry on the PCR-1Z-SM / PCR-1Z / PCR-2Z.
5. Connect the 4 core wire from the PAL 4 Wire LED Lights to the remaining conduit entries at the bottom of the PCR-1Z-SM / PCR-1Z / PCR-2Z. Ensure that the 4 cores are connected to the correct terminals. Two output conduit entries are provided in the enclosure to connect up to 2 PAL-LED 4 Wire Pool Lights.
6. The PCR-1Z / PCR-2Z Driver / Receiver is factory set to operate with the PCZ-2 Transmitter supplied. Fit the 2 x batteries supplied with the PCZ-2. The PCR-1Z-SM does not operate with the PCZ-2 Transmitter. Refer to the information supplied with the PCZ-2 transmitter for full operating instructions and features of the system.

Installation Instructions for PCR-1Z-SM / PCR-1Z RGB Outdoor Driver:
Use the 2 x Mounting legs to fasten the enclosure to the wall with appropriate fixtures for the mounting substrate.
Please refer to the complete user manual for more detailed instructions and safety information.

DIMENSIONS

Knockout Instructions

• It is recommended that the cover is fitted and the cover screws tight when the knockouts are being removed.
• When removing the knock outs place a flat blade screwdriver with a 3/16” (4mm) blade as shown and a light hit with a hammer to the head of the screw driver will allow the Knockout to be removed.
• Alternatively drill location points are located in the centre of each Knock out to allow the use of a hole saw to remove the knockouts.

FEATURES

• Easy to Install
• UL Listed Class 2 Power Supply / Swimming Pool and Spa Transformer (WDGV)
• Remote Control Operation from PCZ-2 hand-held remote
•  Optional Wi-Fi Control from Apple iOS Devices
• IP65 Wet Location Construction
• Constant 24V DC Output Voltage over the Supply

IMPORTANT INFORMATION

• This PCR-1Z-SM/PCR-1Z/PCR-2Z Class 2 power supply is specifically designed to supply 24V DC to power the PAL 4 Wire UL Listed LED Pool lights.
• The PCR-1Z-SM/PCR-1Z/PCR-2Z must be installed in accordance with the National Electrical Code by a Certified Electrician or Qualified Pool Technician.
  NOTE: No bonding is required from this Class 2 power supply to the UL Listed PAL Pool Light fixtures as they are made of an all plastic construction and comply with NEC article 680 requirements.

INSTALLATION INSTRUCTIONS FOR PCR-1Z RGB OUTDOOR DRIVER

• Step 1. The PCR-1Z-SM/PCR-1Z/PCR-2Z Class 2 Power Supply is a Weatherproof construction (IP65) and should be mounted on a flat surface using the mounting legs on the enclosure with appropriate fixtures for the mounting substrate and in a suitable position to suit the intended location of the PAL 4 Wire LED Pool Lights and installed to comply with all the requirements of the National Electrical Code (NEC) and all relevant local codes and ordinances.
  NOTE: The Driver Enclosure must be located a minimum distance of 5 feet measured horizontally from the inside wall of the pool and not less than 1 foot above the maximum pool water level measured to the top of the Driver Enclosure.
  NOTE: The enclosure must be mounted using the mounting legs on the enclosure with the screw set supplied. If the enclosure is to be mounted on a concrete or block wall, mark out the mounting hole locations and drill 3/16” holes using a masonry drill then fit the Star Plugs supplied into the holes and fix using the stainless steel screws supplied??

• Step 2. Using the conduit entry on the bottom (bottom-front on PCR-2Z) right hand side of the PCR-1Z-SM/PCR-1Z/PCR-2Z (as shown) connect the 100-120V power supply to NEC code requirements.

• Step 3. Using the remaining conduit entries at the bottom of the PCR-1Z-SM/PCR-1Z/PCR-2Z (as shown), connect the 4 core wire from the PAL 4 WIRE LED LIGHTS. Please ensure the 4 cores are connected to the correct terminals. 2 x output conduit entries are provided in the enclosure to connect up to 2 x PAL-LED 4 Wire Pool Lights.

• Step 4. The PCR-1Z/PCR-2Z Driver / Receiver is factory set to operate with the PCZ-2 Transmitter supplied. Just fit the 2 x batteries supplied with the PCZ-2.
  The PCR-1Z-SM does not operate with the PCZ-2 Transmitter.
  Please refer to the information supplied with the PCZ-2 transmitter for full operating instructions and features of the system.

INSTALLATION INSTRUCTIONS FOR PCR-1Z-SM / PCR-1Z RGB OUTDOOR DRIVER

INSTALLATION INSTRUCTIONS FOR PCR-2Z RGB OUTDOOR DRIVER

CLONING SETTINGS (PCR-1Z & PCR-2Z AUTOMATION AND PCR-1Z-SM)

Note:

•  Must turn off power before making DIP switch selection.
• When synching PAL lights to other OEM lights, static colors will match but color change mode timing may vary.
• If the PAL Lights are to be used with Automation, do not use the handheld remote control and disconnect the WiFi module from the board if so equipped.
• If the Automation does not turn the PAL lights on or off and there is power to the driver, press the Z1 button one time to turn on the PAL Driver.
•  Note that the PAL features of infinite color selection and dimmability are not available while in Cloned mode.

ZONE SETTINGS – PCR-2Z ONLY

Other Config Operation

• Must turn off power before making DIP switch selection.
• Dip Switch 2: Toggles between 1 and 2 zone operation
• Dip Switch 1: When in single zone mode, this switch selects whether the driver operates entirely as Z1 or Z2 on the remote.
• Dip Switches 3 & 4 change the approximate color temperature of mixed white lights.
  Switch 1| Operation
  ---|---
  ON| Zone 2
  OFF| Zone 1
  Switch 2| Operation
  ---|---
  ON| Single Zone Operation
  OFF| Two Zone Operation

PAL TOUCH PCZ-2 TRANSMITTER HAND HELD REMOTE

FEATURES

1. Matching Code – Apply power to the receiver. Then press Z1 once within 5 seconds. The output light will flash white 3 times if matching is successful.

2. Clearing Code – Apply power to the receiver. Hold down Z1 for 3 seconds. The output light will flash 6 times if clearing the code is successful.
   After successfully clearing the existing code a new code will have to be applied by following the matching code procedure above.

3. 1 Transmitter (PCZ-2) can operate an unlimited number of Receivers (PCR-1Z)

4. 1 Receiver (PCR-1Z) can be controlled by a maximum of 4 Transmitters (PCZ-2)

5. Touching the color wheel will reset any Mode selection.

6. Memory Feature – Remembers color selection after being switched off.

7. Once the transmitter and receiver are successfully coded the receiver will remember the code if powered off.

AUTOMATION DEDICATED LIGHT OUTPUT RELAY FOR CLONE MODE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>