WISYCOM MTP61 Wireless Microphone User Guide
- June 12, 2024
- WISYCOM
Table of Contents
QUICK USER GUIDE
MTP61
MTP61 Wireless Microphone
Main Accesories (find more information at Wisycom.com )
LBC61: Multiple battery charger (4 MTP61 + 4 batteries) + TX management + LTC|
LBP61: rechargeable Lithium-ion battery Model CS-BCE10, Part No. CGA-S008E
3.7V, 1050 mAh, 3.9Wh, Cameron Sino
---|---
CAUSBM5P: Cable from USB/A to magnetic connector 5pin-M, lenght=1050mm for
battery charging, TX management and LTC Time code sync| BCL61: spring loaded
belt clip
LBP61: rechargeable Lithium-ion battery Model CS-BCE10, Cameron Sino Part No.
CGA-S008E. 3.7V, 1050 mAh, 3.9Wh| BCL61: spring loaded belt clip
Conformity
conformity identification is visible on the display by accessing from the Main
menu the Info> STD submenus: step 1: access submenu Info; step 2: access
submenu STD.
| RADIO Directive 2014/53/ EU Radio Equipment Directive (RED)
---|---
| UK Conformity
| FCC-ID: POUMTP61 *
| IC: 11967A-MTP61 **
(*)The Wisycom microphone pocket transmitter model MTP61 complies with the
following requirements: FCC (Federal Communications Commission) Part 74.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operations. Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC ID can be found inside the battery compartment.
This device complies with part 15 of the fcc rules. operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.Note: the grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limitsare designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radiofrequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there isno guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, whichcan be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS-123 and RSS-210
standard. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device. This radio transmitter IC: 11967A-MTP61 has been approved by Industry
Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with
this device.
Antenna types (50 Ohm impedance, max gain 2.1dBi): AWSS-507: band 470-547 MHz,
AWSS-590: band 547-663 MHz, AWSS30-950: band 940-960 MHz.
This equipment complies has been evaluated for and shown compliant with the
FCC and ISED RF Exposure limits. The unit of measurement for RF exposure is
Specific Absorption Rate (SAR). The FCC SAR limits for is 1.6W/Kg per 1g of
tissue The maximum SAR levels tested has been shown to be 0.85 W/kg at head
with 0mm of separation distance from the body.
This device operates on a no-interference, no-protection basis. Should the
user seek to obtain protection from other radio services operating in the same
TV bands, a radio license is required. For further details, consult
Innovation, Science and Economic development Canada’s Client Procedures
Circular CPC-2-128, Voluntary Licensing of License-Exempt Wireless Microphones
in TV Bands.
Serial Number:
Purchase Date:
This guide is intended to assist you with initial quick setup and operation of
your Wisycom product.
You can refer to Wisycom Autorized Distributors for technical Support and
information about service and repairs available in your area or contact us
directly by email.
WISYCOM S.r.l.
Via Tiepolo 7/E
35019 Tombolo (PD) – ITALY
+39 0424 382605
support@wisycom.com
sales@wisycom.com
WISYCOM INC.
14301 Sullyfield Circle, Suite C
Chantilly, VA 20151- USA
+1 703-574-7505
support.us@wisycom.com
sales.us@wisycom.com
Download Documentation and Firmware
Get declarations, user manual, specifications and softwares on the download
page: wisycom.com/products/d/MTP61
Product Registration and Warranty
Register your product to extend your warranty and receive update on latest
firmware: wisycom.com/registration
Keep up with Wisycom online
Follow us on Facebook and Instagram. You can also subscribe on Youtube for
more. wisycom.com/social
Mic Mode | Pinout |
---|---|
2 W | 1 = GND / 3 = AF |
2 W+B | 1 = GND / 3 = AF+5,5 V |
3 W | 1 = GND / 2 = 5,5 V / 3 = AF |
AUX | 1 = GND / 3 = AF (High impedance) |
| Label| Code| Band MHz
---|---|---|---
Antenna type| 507| AWSS-507| 470-547
590| AWSS-590| 547-663
552| AWSS-552| 510-595
646| AWSS-646| 595-698
710| AWSS-710| 663-760
796| AWSS-796| 760-832
808| AWSS-808| 806-810
950| AWSS-950| 940-960
1K1| AWSS-1K1| 960-1160
1K2| AWSS-1K2| 1240-1260