TRUDOOR TDE-E08 Escutcheon Lever Trim Instruction Manual

TRUDOOR TDE-E08 Escutcheon Lever Trim

Product Information

The product is a cylinder collar used in conjunction with a spring spindle. It is designed to extend the length of the spindle if needed. The product also includes a cam and cam screws for converting the TDE-E08 Entry function to Night latch function. The product is compatible with the TDE-E08 and TDE-E14 models. It is important to follow the provided instructions for proper installation and usage.

Product Usage Instructions

To extend the length of the spring spindle, follow these steps:

1. Insert the spring into the spindle hole.

To convert the TDE-E08 Entry function to the Night latch function, follow these steps:

1. Locate the cam and cam screws on the back of the mortise cylinder.
2. Remove the two cam screws and the cam.
3. Rotate the cam 180 degrees and re-install it in the down position.
4. Re-install and tighten the cam screws, being careful not to over-tighten them.
5. Follow the TDE-E08 directions for installing the cylinder into the trim.

Important Notes

• If using an outside trim, drill holes for the outside trim first and install it before drilling holes for the exit device.
• If using a mullion, install the mullion first, then the outside trim, and finally the exit device.
• For TDE-E08 and TDE-E14 models, remove the orange sticker and tighten the handing screw into hole A. Insert the spring first, then the spindle into the back of the lever into hole E.
• For 1000 series, screw thru bolts into the G holes. For 2000 series, screw thru bolts into the C holes and tighten them.
• If a cylinder is required, install it into the cylinder hole with the cylinder collar and secure it with the cylinder retaining ring.
• Follow the provided template for door templating according to the series being used.

Note: The G holes are for 1000 series use, and the C holes are for 2000 series use.

DOOR HANDING

Instructions for converting TDE-E08 Entry to Night latch function

TDE-E08 Entry function can be converted to Night latch function by inverting the cam on the mortise cylinder. The steps below show how to invert the cam:

• Step # 1
  Locate the cam and cam screws on the back of the mortise cylinder.

• Step # 2
  Remove the two cam screws and the cam.

• Step # 3
  Rotate the cam 180 degrees and re-install in the down position. Re-install and tighten the cam screws being careful not to over-tighten them as overtightened screws will make mortise cylinders difficult to operate.

• Step # 4
  Follow TDE-E08 directions for installing the cylinder into the trim.

INSTALLATION INSTRUCTIONS

1. DETERMINE HANDLING OF THE DOOR AS LHR OR HR AND ROTATE THE LEVER TO THE CORRESPONDING POSITION. (SEE FIGURE 5 AND 6).
2. IMPORTANT: REMOVE ORANGE STICKER AND TIGHTEN HANDING SCREW INTO HOLE “A* (SEE FIGURE 2 or 8)
3. INSERT THE SPRING FIRST THEN THE SPINDLE INTO THE BACK OF THE LEVER INTO HOLE “E* (SEE FIGURE 2)
4. FOR 1000 SERIES SCREW THRU BOLTS INTO (4) G HOLES & FOR THE 2000 SERIES, SCREW THRU BOLTS INTO (4) C HOLES AND TIGHTEN.
5. IF A CYLINDER IS REQUIRED, INSTALL THE CYLINDER INTO THE CYLINDER HOLE WITH THE CYLINDER COLLAR AND SECURE WITH THE CYLINDER RETAINING RING.
6. IF LE-02DT DUMMY TRIM IS BEING USED, PUT THE LEVER AT THE REQUIRED HR OR HR POSITION, INSERT SCREWS INTO HOLES F&F, AND TIGHTEN TO MAKE THE LEVER RIGID
7. PROCEED WITH TEMPLATING THE DOOR AS SHOWN IN FIG 7 AND FIG 9 FOR EITHER 1000 OR 2000 SERIES.
8. INSERT LEVER ESCUTCHEON TRIM INTO DOOR PREP. (SEE FIGURE 3) AND SECURE TO EXIT DEVICE USING MOUNTING SCREWS (SEE FIGURE 4).

NOTE: DO NOT REMOVE “B” SCREWS (SEE FIGURE 2) OR THE WARRANTY WILL BE VOID.

• A stock door backset of 2 3/4” can be used but will decrease the backset by 3/16”, this can be offset by not using the 1/8” strike shim to gain 1/8” extra clearance. This will bring the backset within 1/16” which is within acceptable tolerances to operate correctly.

Rim Device on Single Door

• If KRM Mullion is being used,install KRM mullion first, then outside trim adjusting backset according to KRM Mullion backset drawing and then install exit device.

Rim x Rim x Mullion on Pair of Doors

• When installing Rim device x SVR device on a pair of doors a Double Door Strike (DDS) is required. For complete template information, please refer to the DDS template.

Rim w/ DDS x Surface Vertical Rod on a Pair of Doors

• For complete template information Please refer to the Surface Vertical Rod exit device template.
• Surface Vertical Rod x Surface Vertical Rod on a Pair of Doors

INTERIOR SIDE OF DOOR

NOTE:(A) 4 G HOLES ARE FOR 1000 SERIES USE. (B) 4 C HOLES ARE FOR 2000 SERIES USE.

EXTERIOR SIDE OF DOOR

NOTE: (A) 4 G HOLES ARE FOR 1000 SERIES USE. (B) 4 C HOLES ARE FOR 2000 SERIES USE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>