Pyle PWRC52 Ceiling Wall Mount Speakers User Manual

: June 12, 2024
: Pyle

Table of Contents

Pyle PWRC52 Ceiling Wall Mount Speakers
INCLUDED
INSTALLTION
- TROUBLESHOOTING
WIRING DIAGRAM
SPEAKER CONNECTIONS
EXISTING CONSTRUCTION
FREQUENTLY ASKED QUESTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Pyle PWRC52 Ceiling Wall Mount Speakers

Pyle PWRC52 Ceiling Wall Mount Speakers-product

Thank you for purchasing this PYLE in-wall/in-ceiling speaker system. It is a state-of-the-art product carefully designed and manufactured for your installation needs and has been thoroughly tested to ensure consistent and reliable performance. If you have any questions about the installation or operation of your PYLE in-wall/in-ceiling speaker system which are not answered by this manual, contact your dealer immediately.

INCLUDED

IN-WALL SPEAKERS

IN-CEILING SPEAKERS

$Pyle PWRC52 Ceiling Wall Mount Speakers-fig- $2$$

SPEAKER PLACEMENT

FRONT SPEAKERS

INSTALLTION

The in-wall/in-ceiling speakers were designed to be easily installed, However, if you are unsure of your ability to prop- erly install these loudspeakers please contact your dealer or a qualified installer.

TROUBLESHOOTING

IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:

Check that the receiver/amplifier is on and a source is playing.
Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
Review the proper operation of your receiver/amplifier.

IF THERE IS NO SOUND COMING FROM ONE SPEAKER:

Check the “Balance control on your receiver/amplifier.

Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.

IF THERE IS LOW (OR NO) BASS OUTPUT:

Make sure the connections to the left and right Speaker Inputs* have the correct polarity (+ and -).
Consider adding a powered subwoofer to your system. + In Dolby Digital or DTS modes, make sure your receiver/ processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/ processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as “LARGE.” See your receiver/processor’s owner’s manual for further information on the correct speaker configuration in Dolby Digital, DTS and other surround sound modes.

IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED-

Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.

If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.

WIRING DIAGRAM

(PDIC60T/PDIC80T)

$Pyle PWRC52 Ceiling Wall Mount Speakers-fig- $5$$

REAR SPEAKERS

IN-CELLING

Proper placement of the soakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The front speakers should be placed in the same distance from each other as they are from the listening position. They should sa saris the same belt from the foor as the listener’s ears wit be, with the tweeters aimed toward the listener at ear-lovel height. In a home theater configuration, the two surround speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listener’s cars. If that is not possible, they may be placed in a wall (or in the ceiling) behind the listening position, facing forward. The surround speakers should not call attention to themselves. They should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers. In Dolby’s” Digital and DTS” systems, aim the tweeters toward the listening position at ear-level height.

SPEAKER CONNECTIONS

CONNECTION TIPS

Tho wires or both speakers should be the same length. One speaker is placed closer to the amplifier than the other. hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and (-] terminals. We use red to denote the (*] terminal and black for the (-) terminal. It is important to connect both speakers identically: (+) on the speaker to (4) on the amplifier and f-jon the speaker to (-) on the amplifier. Wiring out of phase results in a thin sound and an odor steres image. With the advent of multi-channel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambiance and directionality of the program material.

EXISTING CONSTRUCTION

IN-WALL SPEAKER

$Pyle PWRC52 Ceiling Wall Mount Speakers-fig- $9$$

Cut the drywall. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.
Screw out the two screws to separate the frame first.
Place the frame assembly on the wall. Screw down each of the six § Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall
Connect the speaker wires to the speaker. Screw down each of the six Philips head screws.
Put in the strips of adhesive to secure the grille.
The in-wall speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. PDIW55/PDIW6S/PDIW57/PDIW67/PDIW87 PDIWS28/PDIWS&/PDIWS10/PDIWS12 PDIWCS56/PDIWCS62 tweeter adjustment: Before installing the speaker grille. gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further.
Replace the metal grille.

PDIW52/PDIW62

After installing the speaker grille gently press on the mesh of the tweeter to adjust the position of the tweeter.

IN-CEILING SPEAKERS

$Pyle PWRC52 Ceiling Wall Mount Speakers-fig- $14$$

Cut the drywall,
Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.
Connect the speaker wires to the speaker.
Place the frame assembly on the wall
Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. Put in the strips of adhesive to secure the grille.
The in-celling speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grille. gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further.
Replace the metal grille.
Just for PDIC60/PDIC80 After installing the speaker grille, gently press on the mesh of the tweeter to adiust the position of the tweeter.

IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS

Check that the receiver/amplifier is on and a source is playing.

Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, out, punctured or touching each other.
Review the proper operation of your receiver/amplifier.

IF THERE IS NO SOUND COMING FROM ONE SPEAKER:

Check the “Balance” control on your receiver/amplifier.*
Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.

IF THERE IS LOW (OR NO) BASS OUTPUT:

Make sure the connections to the left and right “Speaker Inputs* have the correct polarity (+ and -). + Consider adding a powered subwoofer to your system.
In Dolby Digital or DTS modes, make sure your receiver/ processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as “LARGE.” See your receiver/processor’s owner’s manual for further information on the correct speaker configuration in Dolby Digital, DTS and other surround sound modes.

IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:

Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.