makita EN422MP Ground Trimmer Attachment Set Instruction Manual

makita EN422MP Ground Trimmer Attachment Set

Product Information

• Model: EN422MP
• Blade Length: 250 mm
• Overall Length: 1208 mm
• Net Weight: 2.2 kg
• Approved Power Unit: [Not specified]
• Guaranteed Sound Power Level: According to EU Outdoor Noise Directive

Intended Use:
The EN422MP Ground Trimmer Attachment is designed for trimming shrubs, hedges, and grasses on the ground in conjunction with an approved power unit. It should not be used for any other purpose.

Product Usage Instructions

1. Ensure you have an approved power unit to use with the EN422MP Ground Trimmer Attachment. Using a non-approved power unit may cause serious injury.
2. Before using the attachment, read and understand the instruction manual provided.
3. Ensure that you are wearing appropriate personal protective equipment, including a protective helmet, eye and ear protection, and protective gloves.
4. Keep your hands away from the blade at all times.
5. Beware of electrical lines to avoid the risk of electrical shock.
6. Wear sturdy boots with non-slip soles to maintain stability while operating the attachment.
7. Keep bystanders and animals at least 15 meters (50 feet) away from the power tool to prevent accidents.
8. Clear the area of operation from all persons and pets to ensure their safety.
9. When carrying the hedge trimmer, hold it by the handle with the blade stopped. Do not operate any power switch while carrying it to avoid inadvertent starting and potential personal injury from the blades.

For detailed safety warnings and additional instructions, refer to the instruction manual provided with the product.

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.

Approved power unit
This attachment is approved to use only with the follow-ing power unit(s):

• DUX60 Cordless multi function power head
• DUX18 Cordless multi function power head
• UX01G Cordless multi function power head

WARNING:
Never use the attachment with non-approved power unit. Non-approved combi- nation may cause serious injury.

Symbols
The followings show the symbols which may be used for the equipment. Be sure that you understand their meaning before use.

• Read and follow the instruction manual.
• DANGER – Keep hands away from blade.
• Beware of electrical lines. Risk of electrical shock.
• Wear protective helmet, eye and ear protection.
• Wear protective gloves.
• Wear sturdy boots with non-slip soles.
• Keep bystanders and animals at least 15 m (50 ft) away from the power tool.
• Keep the area of operation clear of all persons and pets.
• Guaranteed sound power level according to EU Outdoor Noise Directive.
• Sound power level according to Australia NSW Noise Control Regulation.

Intended use
This attachment is designed for only the purpose of trimming shrubs, hedges, and grasses on the ground in conjunction with an approved power unit. Never use the attachment for the other purpose. Abusing the attach-ment may cause serious injury.

Declaration of Conformity

EC Declaration of Conformity

For European countries only

We as the manufacturers:
Makita Europe N.V., Business address: Jan-Baptist Vinkstraat 2 3070 Kortenberg BELGIUM. Authorize Hiroshi Tsujimura for the compilation of the technical file and declare under our sole responsibility that the product(s); Designation: Ground Trimmer Attachment. Designation of Type(s): EN422MP.

Fulfills all the relevant provisions of 2006/42/EC and also fulfills all the relevant provisions of the following EC/EU Directives: 2000/14/EC and are manufactured in accordance with the following Harmonised Standards: EN62841-1:2015, EN 62841-4-2:2019, EN ISO 11806-1:2011.

• Place and date of declaration: Kortenberg, Belgium. 20. 12. 2022
• Responsible person: Hiroshi Tsujimura, Director -Makita Europe N.V.

Declaration of Conformity (For UK)

For UK only
We as the manufacturers: Makita Europe N.V., Business address: Jan-Baptist Vinkstraat 2 3070 Kortenberg BELGIUM. Authorize Hiroshi Tsujimura for the compilation of the technical file and declare under our sole responsibility that the product(s); Designation: Ground Trimmer Attachment. Designation of Type(s): EN422MP.

Fulfills all the relevant provisions of S.I. 2008/1597 (as amended) and also fulfills all the relevant provisions of the following UK Regulations: S.I. 2001/1701 (as amended) and are manufactured in accordance with the following Designated Standards: EN62841-1:2015, EN 62841-4-2:2019, EN ISO 11806-1:2011.

Place and date of declaration: Kortenberg, Belgium. 20. 12. 2022

• Responsible person: Hiroshi Tsujimura, Director -Makita Europe N.V.
• Importer: Makita (UK) Limited, Michigan Drive, Tongwell, Milton Keynes, Buckinghamshire, MK15 8JD, UK

SAFETY WARNINGS

Cordless Pole Hedge Trimmer Safety Warnings

1. Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal injury.
2. Carry the hedge trimmer by the handle with the blade stopped and taking care not to operate any power switch. Proper carrying of the hedge trimmer will decrease the risk of inadvertent start-ing and resultant personal injury from the blades.
3. When transporting or storing the hedge trim-mer, always fit the blade cover. Proper handling of the hedge trimmer will decrease the risk of personal injury from the blades.
4. When clearing jammed material or servicing the unit, make sure all power switches are off and the battery pack is removed or discon-nected. Unexpected actuation of the hedge trim-mer while clearing jammed material or servicing may result in serious personal injury.
5. Hold the hedge trimmer by insulated gripping surfaces only, because the blade may contact hidden wiring. Blades contacting a “live” wire may make exposed metal parts of the hedge trim-mer “live” and could give the operator an electric shock.
6. Keep all power cords and cables away from cutting area. Power cords or cables may be hid-den in hedges or bushes and can be accidentally cut by the blade.
7. Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.
8. To reduce the risk of electrocution, never use the pole hedge trimmer near any electrical power lines. Contact with or use near power lines may cause serious injury or electric shock result-ing in death.
9. Always use two hands when operating the pole hedge trimmer. Hold the pole hedge trimmer with both hands to avoid loss of control.
10. Always use head protection when operating the pole hedge trimmer overhead. Falling debris can result in serious personal injury.

Additional Safety Instructions

Preparation

1. THIS HEDGE TRIMMER CAN CAUSE SERIOUS INJURIES. Read the instructions carefully for the correct handling, preparation, main-tenance, starting and stopping of the tool. Become familiar with all controls and the proper use of the tool.

2. Check the hedges and bushes for foreign objects, such as wire fences or hidden wiring before operating the tool.

3. The tool must not be used by children or young persons under 18 years of age. Young persons over 16 years of age may be exempted from this restriction if they are undergoing training under the supervision of an expert.

4. 4. In the event of an emergency, switch off
   the tool and remove the battery cartridge immediately.

5. DANGER – Keep hands away from blade. Contact with blade will result in serious personal injury.

6. First-time users should have an experienced user show them how to use the tool.

7. Before operation, examine the work area for wire fences, stones, or other solid objects. They can damage the blades.

8. Use the tool only if you are in good physical condition. If you are tired, your attention will be reduced. Be especially careful at the end of a working day. Perform all work calmly and carefully. The user is responsible for all damages to third parties.

9. Before starting work, check to make sure that the tool is in good and safe working order. Ensure guards are fitted properly. The tool must not be used unless fully assembled.

10. Avoid dangerous environment. Don’t use the tool in damp or wet locations or expose it to rain. Water entering the tool will increase the risk of electric shock.

Personal protective equipment

1. Work gloves of stout leather are part of the basic equipment of the tool and must always be worn when working with it. Also wear sturdy shoes with anti-skid soles.
2. Wear ear protection such as ear muffs to pre-vent hearing loss.
3. Wear protective goggles, safety helmet and protective gloves to protect yourself from flying debris or falling objects.
4. When touching blades or adjusting the blade angle, wear protective gloves. Blades can cut bare hands severely.

Operation

1. Always use two hands to operate the tool. Using one hand could cause loss of control and result in serious personal injury.
2. While operating the tool, always ensure that the operating position is safe and secure. Overreaching with the tool, particularly from a ladder, is extremely dangerous. Do not work from anything wobbly or infirm.
3. Do not simultaneously wear multiple belt har-nesses and/or shoulder harnesses when oper-ating the tool.
4. During operation, keep bystanders or animals at least 15 m away from the tool. Stop the tool as soon as someone approaches.
5. If cutting tool strikes any object or the tool starts making unusual noise or vibration, switch off the tool and remove the battery car-tridge immediately and allow the tool to stop. And then take the following steps:
   • inspect for damage
   • check for, and tighten, any loose parts
   • have any damaged parts replaced or repaired with genuine spare parts.
6. Only use the tool for its intended purpose. Do not use the tool for any other purpose.
7. Switch off the tool and remove the battery cartridge before:
   • cleaning or when clearing a blockage,
   • checking, carrying out maintenance or working on the tool,
   • adjusting the working position of the shear blades,
   • leaving the tool unattended.
8. Ensure that the tool is correctly located in a designated working position before starting the tool.
9. Do not operate the tool with a damaged or excessively worn shear blades.
10. Always be aware of your surroundings and stay alert for possible hazards of which you may not be aware due to the noise of the tool.
11. Be careful not to accidentally contact a metal fence or other hard objects during operation. The blade will break and may cause serious injury.
12. Avoid unintentional starting. Do not carry the tool when the battery cartridge is installed and with finger on the switch. Make sure that the switch is off when installing the battery cartridge.
13. Do not grasp the exposed cutting blades or cutting edges when picking up or holding the tool.
14. Do not force the tool. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.
15. Do not use the tool in the rain or in wet or very damp conditions. The electric motor is not waterproof.
16. Hold the tool firmly when using the tool.
17. Do not operate the tool at no-load unnecessarily.
18. Before checking the shear blades, taking care of faults, or removing foreign objects caught in the shear blades, always switch off the tool and remove the battery cartridge.
19. Never point the shear blades to yourself or others.
20. If the blades stop moving due to the stuck of foreign objects between the blades during operation, switch off the tool and remove the battery cartridge, and then remove the foreign objects using tools such as pliers. Removing the foreign objects by hand may cause an injury for the reason that the blades may move in reac-tion to removing the foreign objects.
21. When attaching or removing the blade cover, be careful not to injure your hands.

Electrical and battery safety

1. Avoid dangerous environment. Don’t use the tool in damp or wet locations or expose it to rain. Water entering the tool will increase the risk of electric shock.
2. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
4. Do not charge battery in rain, or in wet locations.
5. Do not charge the battery outdoors.
6. Do not handle charger, including charger plug, and charger terminals with wet hands.

Maintenance and storage

1. When the tool is stopped for servicing, inspec-tion or storage, switch off the tool and remove the battery cartridge, and make sure all mov-ing parts have come to a stop. Allow the tool to cool before making any inspections, adjust-ment, etc.
2. Always allow the tool to cool down before storing.
3. When not in use, attach the blade cover to the tool and store the tool indoors in dry, and high locked-up place, out of reach of children.
4. Maintain the tool with care. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Keep grips dry, clean, and free from oil and grease.
5. Check damaged parts. Before further use of the tool, any part which is damaged should be carefully checked to determine that it will oper-ate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by your authorized service center.
6. Use genuine spare parts only.
7. When moving the tool to another location, including during work, always remove the battery cartridge and put the blade cover on the shear blades. Never carry or transport the tool with the blades running. Never grasp the blades with your hands.
8. Clean the tool and especially the shear blades after use, and before putting the tool into stor-age for extended periods. Lightly oil the shear blades and put on the blade cover.
9. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
10. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
11. Do not charge battery in rain, or in wet locations.

SAVE THESE INSTRUCTIONS.

WARNING:
DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

PARTS DESCRIPTION

Fig.1:

1. Blade cover
2. Angle adjustment handle
3. Cap
4. Shear blades
5. Slide lever
6. Front grip

ASSEMBLY

• WARNING: Before assembling or adjusting the equipment, switch off the motor and remove the battery cartridge. Otherwise, the machine may start unintentionally and result in an injury.
• WARNING: When assembling or adjusting the equipment, always put it down. Assembling or adjusting the equipment in an upright position may result in serious injury.
• WARNING: Follow the warnings and precau-tions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.

Assembling the attachment

1. Remove the cap from the attachment.  Fig.2:
2. Cap
3. Insert the pipe into the attachment so that the hole on the pipe is aligned with the hole on the attachment. Securely tighten the short bolt first, and then tighten the long bolt to fix the pipe. Fig.3:
4. Hole
5. Pipe
6. Bolt (short)
7. Bolt (long)

NOTE:
When tightening the bolts, apply 4.0 – 6.0 N•m as tightening torque.

Mounting the attachment pipe

CAUTION:
Always check that the attachment pipe is secured after installation. Improper instal-lation may cause the attachment falling off from the power unit and cause personal injury.

Mount the attachment pipe to the power unit.

1. Remove the cap from the end of the pipe. Fig.4:

2. Pipe

3. Cap
   NOTICE: Do not dispose of the cap since the cap is necessary for storing the attachment.

4. Turn the lever toward the attachment. Fig.5:

5. Lever

6. Align the pin with the arrow mark on the power unit. Insert the pipe until the release button pops up. Make sure that the position line is on the tip of the arrow mark on the power unit, and the arrow mark on the power unit and the arrow mark on the pipe are facing each other. Fig.6:

7. Release button

8. Arrow mark on the power unit

9. Pin

10. Position line

11. Arrow mark on the pipe

12. Turn the lever toward the power unit. Fig.7:

13. Lever

NOTICE:
Do not tighten the lever without the attachment pipe inserted. Otherwise the lever may tighten the entrance of the drive shaft too much and damage it.

To remove the pipe, turn the lever toward the attach-ment and pull the pipe out while pressing down the release button. Fig.8:

1. Release button
2. Lever
3. Pipe

Installing or removing the shear blades

• CAUTION: When replacing the shear blades, always wear gloves so that your hands do not directly contact the blades.
• CAUTION: Attach the blade cover before removing or installing the shear blades.
• NOTICE: When replacing the shear blades, do not wipe off grease from the crank.
• NOTE: Before installing or removing the shear blades, unfold the attachment so that the attachment is straight to the pipe.

1. Attach the blade cover to the shear blades. Fig.9:
2. Blade cover
3. Place the attachment upside down.
4. Remove 4 bolts with the hex wrench, and remove the under cover, cover and plate (large). Fig.10:
5. Bolt
6. Under cover
7. Cover
8. Plate (large)
9. Turn the crank with the slotted screwdriver so that the crank is positioned in the direction as shown in the figure. Fig.11:
10. Crank
11. Remove 2 bolts. Fig.12:
12. Bolt
13. Remove the felt pad (short), felt pad (long), plate (small), and sleeves. Fig.13:
14. Felt pad (short)
15. Felt pad (long)
16. Plate (small)
17. Sleeve
18. Remove the shear blades from the attachment. Fig.14
19. Remove the blade cover, and then attach it to the new shear blades.
20. Remove the dust guard from the shear blades, and then attach it in the position shown in the figure on the new shear blades. Fig.15:
21. Dust guard
22. Insert the bolt removed in step 5 into the hole on the shear blades through the hole on the blade cover. Fig.16:
23. Hole
24. Bolt
25. Apply a small amount of grease to the periphery of the crank. Attach the shear blades to the attachment. Fig.17
26. Attach the sleeves, plate (small) to the shear blades, and then tighten the bolt. Fig.18:
27. Bolt
28. Plate (small)
29. Sleeve
30. Remove the bolt inserted into the hole on the shear blades in step 10, and then tighten it to fix the shear blades.
31. Attach the felt pad (short) and felt pad (long). Fig.19:
32. Felt pad (short)
33. Felt pad (long)
34. Attach the plate (large), cover, and under cover, and then tighten 4 bolts. Fig.20:
35. Bolt
36. Under cover
37. Cover
38. Plate (large)

• NOTICE: If the shear blades do not operate prop-erly, the blades are not engaging the crank prop-erly. Remove the blades and install them again.
• NOTICE: If the parts other than the shear blades such as the crank are worn out, ask Makita Authorized Service Centers for parts replacement or repairs.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

Adjusting the cutting angle

CAUTION:
Always be sure that the tool is switched off before adjusting the cutting angle.

The angle of the head can be adjusted in 13 steps. To change the angle of the head, follow the steps below.

1. Hold the angle adjustment handle, and then adjust the angle of the head while pulling the slide lever, and then release the slide lever. Fig.21:
2. Slide lever
3. Angle adjustment handle
4. Move the head slightly until it is locked with a click.

NOTE:
Make sure that the head is securely locked before operating the tool.

OPERATION

WARNING:
Follow the warnings and precau-tions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.

Operating the tool

• WARNING: Do not use the tool near any electrical power lines. Contacting with power lines or using the tool near power lines may cause serious injury or electric shock resulting in death.
• WARNING: Keep hands away from shear blades.
• WARNING: Be extremely careful to maintain control of the tool at all times. Do not allow the tool to be deflected toward you or anyone in the work vicinity. Failure to keep control of the tool could result in serious injury to the bystander and the operator.
• CAUTION: Avoid operating the tool in very hot weather as much as practicable. When operat-ing the tool, be careful of your physical condition.
• CAUTION: Be careful not to accidentally contact a metal fence or other hard objects while trimming. The shear blades may break and cause an injury.
• CAUTION: Be careful not to allow the shear blades to contact the ground. The tool may recoil and cause an injury.
• CAUTION: Overreaching with a hedge trim-mer, particularly from a ladder, is extremely dangerous. Do not work while standing on anything wobbly or infirm.
• NOTICE: Do not attempt to cut branches thicker than 10 mm in diameter with the tool. Cut branches to 10 cm lower than the cutting height using branch cutters before using the tool. Fig.22:

1. Cutting height
2. 10 cm

• NOTICE: Do not cut down dead trees or similar hard objects. Doing so may damage the tool.
• Hold the tool with both hands by holding the front han-dle of the power unit or the front grip of the attachment and the rear grip of the power unit. Fig.23:

1. Front handle
2. Rear grip

• Pull the switch trigger while pressing the lock-off lever, and then move the tool forward.  Fig.24
• For basic operation, tilt the shear blades toward the trimming direction and move it calmly and slowly at the speed rate of 3 to 4 seconds per meter. Fig.25
• To cut a hedge side evenly, cut from the bottom to top. Fig.26
• When trimming to make a round shape (trimming box-wood or rhododendron, etc.), trim from the root to the top for a beautiful finish.  Fig.27
• When shearing the grass, apply the shear blades to the grass parallel to the ground, and shear the grass with a right to left swinging movement.  Fig.28

MAINTENANCE

• WARNING: Before inspecting or maintaining the equipment, switch off the motor and remove the battery cartridge. Otherwise, the machine may start unintentionally and result in serious injury.
• WARNING: When inspecting or maintaining the equipment, always put it down. Assembling or adjusting the equipment in an upright position may result in serious injury.
• WARNING: Follow the warnings and precau-tions in the chapter “SAFETY WARNINGS” and the instruction manual of the power unit.
• CAUTION: Wear gloves when performing the inspection or maintenance.
• NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

Cleaning the tool

Clean the tool by wiping off dust with a dry cloth or one dipped in soapy water and wrung out.

NOTICE:
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Shear blade maintenance

• Before the operation or once per hour during operation, apply low-viscosity oil (machine oil, or spray-type lubri-cating oil) to the shear blades.  Fig.29
• After operation, remove dust from both sides of the shear blades with a wired brush, wipe it off with a cloth and then apply low-viscos-ity oil (machine oil, or spray-type lubricating oil) to the shear blades.  Fig.30
• NOTICE: Do not wash the shear blades in water. Doing so may cause rust or damage to the tool.
• NOTICE: Dirt and corrosion cause excessive blade friction and shorten the operating time per battery charge.

Storage

Attach the blade cover to the shear blades so that the blades are not exposed. Store the tool out of the reach of children. Store the tool in a place not exposed to moisture or rain. When storing the attachment separated from the power unit, put the cap onto the end of the pipe.  Fig.31

Lubricating moving parts

NOTICE:
Follow the instruction of the frequency and amount of grease supplied. Otherwise insuffi-cient lubrication may damage moving parts.

Drive axle:
Apply grease (Makita grease N No.2 or equivalent) every 30 hours of operation. Fig.32

NOTE:
Genuine Makita grease may be purchased from your local Makita dealer.

Grease lubrication

Interval of lubrication:
Every 25 operating hours

1. Remove the bolt from the hole for lubrication. Fig.33:
2. Bolt
3. Remove the cap from the grease vessel. Align the outlet of the grease vessel with the hole on the cover, and then turn the grease vessel to attach the outlet of the grease vessel into the hole. Fig.34:
4. Grease vessel
5. Hole
6. Apply the grease to the tool (Approximately 3 g as a guide).
7. Remove the grease vessel.
8. Tighten the bolt.

Grinding the shear blades

NOTICE:
If the shear blades have considerably deformed by grinding, replace the shear blades with new ones.

1. Install the battery cartridge to the tool.

2. Turn on and start the tool so that the upper blade and lower blade are positioned alternately.  Fig.35

3. Turn off the tool and remove the battery cartridge from the tool.

4. Remove the screws and nut, and then remove the tip guard from the shear blades. Fig.36:

5. Screw

6. Nut

7. Tip guard

8. Set the angle of a file to 45°, and grind the upper blade from 3 directions with the file. Fig.37:

9. File (2) 45°
   CAUTION: Before grinding the shear blades, make sure that the tool is switched off and the battery cartridge is removed from the tool.

10. Place the tool upside down, and then remove the burrs from the shear blades with the dressing stone. Fig.38:

11. Dressing stone

12. Set the angle of the file to 45°, and grind the lower blade from 3 directions with the file.

13. Return the tool to normal position, and then remove the burrs from the shear blades with the dressing stone.

14. Attach the tip guard by tightening the screws and nut.

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-ment parts for repairs.

State of abnormality| Probable cause (malfunction)| Remedy
---|---|---
Motor does not start.| –| Refer to the instruction manual of the power unit.
Motor stops soon.| –| Refer to the instruction manual of the power unit.
Motor speed does not increase.| –| Refer to the instruction manual of the power unit.
Shear blades do not move:

stop the machine immediately!

| Foreign objects are caught between the shear blades.| Switch off the tool and remove the battery cartridge, and then remove the foreign objects using tools such as pliers.
The drive system does not work correctly.| Ask your local authorized service center for repair.
Abnormal vibration:

stop the machine immediately!

| Shear blades are broken, bent or worn.| Replace the shear blades.
The drive system does not work correctly.| Ask your local authorized service center for repair.
Shear blades and motor cannot stop: Remove the battery immediately!| Electric malfunction.| Remove the battery and ask your local authorized

service center for repair.

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments are recommended for use with your Makita machine specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attach-ment for its stated purpose.

If you need any assistance for more details regard-ing these accessories, ask your local Makita Service Center.

• Shear blade assembly
• Grease vessel
• Makita genuine battery and charger

NOTE:
Some items in the list may be included in the product package as standard accessories. They may differ from country to country.

Makita Europe N.V.
Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium.

Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan.

www.makita.com.

References

• MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>