SUNCO LIGHTING Vapor Tight Installation Guide

SUNCO LIGHTING Vapor Tight

Product Information:

The Vapor Tight Installation Guide provides instructions for installing and maintaining the fixture. It is important to read and follow the safety instructions and comply with local codes and ordinances. The fixture should not be cleaned or maintained while energized, and caution should be exercised to avoid the risk of fire.
The fixture has a non-abrasive lens that can be cleaned using a non-abrasive cleaning solution. However, the LED should not be touched or opened for cleaning. The instructions also mention that they may not cover all details or variations in equipment or every possible situation during installation, operation, or maintenance.
The troubleshooting section advises checking the line voltage and proper grounding of the fixture. Additionally, the wiring instructions for dimmable operation specify how to connect the fixture leads to the power supply.
The installation guide provides instructions for surface mount installation. It includes step-by-step illustrations for mounting brackets, opening clips, releasing the LED chip board, installing a waterproof connector, connecting wires, re-attaching the lens, and fastening the clips on the fixture.
The guide also explains how to select wattage and color temperature for different models of the fixture. It mentions the default wattage options and provides instructions on locating and adjusting the black toggle switches inside the fixture to change the wattage or color temperature settings.

Product Usage Instructions

Cleaning & Maintenance

1. Clean the lens with a non-abrasive cleaning solution.
2. Do not open the fixture to clean the LED or touch the LED.

Troubleshooting

1. Check that the line voltage at the fixture is correct by referring to the wiring directions.
2. Check that the fixture is grounded properly.

0-10V Dimmable Wiring:

The fixture’s universal voltage driver allows operation at 120V through 277V, 50/60Hz.

1. Connect the BLACK fixture lead to the (+) LINE supply lead.

2. Connect the WHITE fixture lead to the (-) COMMON supply lead.

3. Connect the GROUND wire from the fixture to the supply ground.
   Do not connect the GROUND of the dimming fixture to the output.

4. Connect the VIOLET fixture lead to the (V+) DIM lead.

5. Connect the GRAY fixture lead to the (V-) DIM lead.

Vapor Tight Installation – Surface Mount:
Follow the steps below for surface mount installation:

1. Install the mounting brackets to the installation surface.
2. Open the clips on the fixture.
3. Release the LED chip board inside the fixture by pinching the metal clips together in the middle of the board.
4. Install the waterproof connector to the fixture.
5. Connect the wires according to the provided illustration.
6. Re-attach the lens to the housing.
7. Fasten the clips on the fixture.
8. Install the fixture to the mounting brackets.

Selectable Wattage and Color Temperature:
To select wattage or color temperature, follow these steps:

Selecting Wattage:

1. Locate the 2 black toggle switches inside the fixture when the LED chip board is lifted.
2. To change the wattage, select the silver box labeled with wattage. The default wattage is the highest option on the fixture (left position). Adjust by pushing the switch to the middle or right for lower wattage.

Selecting Color Temperature:

1. Locate the 2 black toggle switches inside the fixture when the LED chip board is lifted.
2. To change the color temperature, select the silver box labeled with CCT. The default color temperature is the highest option on the left side (5,000K). Adjust by pushing the switch to the middle (4,000K) or right side (3,500K).

Please refer to the user manual for more detailed instructions and additional information.

Vapor Tight Installation Guide

SAFETY INSTRUCTIONS:   Read instructions carefully before attempting to install fixture.

• All wiring should be performed by a qualified electrician.
• Disconnect power before installing or servicing. This fixture must be wired in accordance with the National ElectricalCode and applicable local codes and ordinances.

CAUTION: Risk of fire

WARNING: Make certain power is OFF before installing or maintaining fixture. No user-serviceable parts inside.•WARNING: Do NOT handle energized fixture when hands are wet, when standing on wet or damp surfaces or inwater.•WARNING: Fixture to be independently supported to building structure.

CLEANING & MAINTENANCE

CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.

1. Clean lens with non-abrasive cleaning solution.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
   Note: These instructions do not cover all details or variation in equipment, nor do they provide for every possible situation during installation, operation or maintenance.

TROUBLESHOOTING

1. Check that the line voltage at fixture is correct. Refer to wiring directions.
2. Check that the fixture is grounded properly.

0-10V DIMMABLE WIRING:

Universal voltage driver permits operation at 120V through 277V, 50/60Hz.

1. Connect the BLACK fixture lead to the (+) LINE supply lead.
2. Connect the WHITE fixture lead to the (-) COMMON supply lead
3. Connect the GROUND wire from fixture to the supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
4. Connect the VIOLET fixture lead to the (V+) DIM lead.
5. Connect the GRAY fixture lead to the (V-) DIM lead.

INSTALLATION OPTION

Surface Mount

CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.

SURFACE MOUNT

1. Install the mounting brackets to the installation surface. (Fig. 1)
2. Open the clips on the fixture. (Fig. 2)
3. Release the LED chip board inside the fixture by pinching the metal clipsto gether on the middle of the board. (Fig. 3)
4. Install the waterproof connector to the fixture. (Fig. 4)
5. Connect the wires. (Fig. 5)
6. Re-attach the lens to the housing. (Fig. 6)
7. Fasten the clips on the fixture. (Fig. 7)
8. Install the fixture to the mounting brackets. (Fig. 8)

SELECTABLE WATTAGE AND COLOR TEMPERATURE

Selecting Wattage:

1. When you take the LED chip board up from the fixture, locate 2 black toggle switches inside the fixture. Each silver box is labeled with options to select a wattage or options to select a color temperature.
2. To change the wattage, please select the silver box with wattage. The default wattage is the highest wattage option on the fixture (left position). You can adjust this by pushing the switch to the middle or the right (lowest wattage).

2 FOOT MODEL NUMBER:| Default Wattage (Left)| Middle Wattage (Middle)| Lowest Wattage (Right)
---|---|---|---
LO-LOC-2FTVT-MW-MCCT| 30W| 25W| 20W

4 FOOT MODEL NUMBER:| Default Wattage (Left)| Middle Wattage (Middle)| Lowest Wattage (Right)
LO-LOC-4FTVT-MW-MCCT| 50W| 35W| 25W

8 FOOT MODEL NUMBER:| Default Wattage (Left)| Middle Wattage (Middle)| Lowest Wattage (Right)
LO-LOC-8FTVT-MW-MCCT| 90W| 75W| 60W

Selecting Color Temperature:

1. When you take the LED chip board up from the fixture, locate 2 black toggle switches inside the fixture. Each silver box is labeled with options to select a wattage or options to select a color temperature.
2. To change the color temperature, please select the silver box with CCT. The default color temperature is the highest temperature option on the fixture left side 5,000K. You can adjust this by pushing the switch to the middle 4,000K or the right side 3,500K.

Default Color Temperature (Left)| Middle Color Temperature (Middle)| Lowest Color Temperature (Right)
---|---|---
5,000K| 4,000K| 3,500K

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>