thermaltake TPG-0850D Toughpower DPS Power Supply Instruction Manual

: June 4, 2024
: thermaltake

Table of Contents

thermaltake TPG-0850D Toughpower DPS Power Supply Instruction Manual
Warnings and Caution
Components Check
Power Connector Introduction
CABLE P/N
Output Specification
Installation Steps
Total Protection
EMI & SAFETY
Trouble-Shooting
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

thermaltake TPG-0850D Toughpower DPS Power Supply Instruction Manual

Warnings and Caution

Do not unplug the AC power cord when the power supply is in use. Doing so may cause damage to your components.
Do not place the power supply in a high humidity and/or temperature environment.
High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
The power supply should be powered by the source indicated on the rating label.
Please use only genuine Thermaltake modular cables with Thermaltake Cable Management power supply models.Third party cables might not be compatible and could cause serious damage to your system and power supply. The warranty is voided with the use of third party cables.
All warranties and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this manual.

Components Check

TOUGH POWER GRAND power supply unit
AC power cord
User manual
Mounting screws x 4
Cable straps x 4

Power Connector Introduction

CABLE P/N

| | | | | |
---|---|---|---|---|---|---
| Main Power Connector (24 Pin)| ATX 12 V Connector (4+4 Pin)| SATA Connector (5 Pin)| PCI-E Connector (6+2 Pin)| Peripheral Connector (4 Pin)| PATA to FDD (4 Pin)
TPG-0850F-R| 1| 2| 12| 6| 4| 1
TPG-0750F-R| 1| 1| 9| 4| 4| 1
TPG-0650F-R| 1| 1| 9| 4| 4| 1

Output Specification

P/N| AC INPUT| Input Voltage: 100V – 240V~ ; Input Current: 12A ; Frequency: 50Hz – 60Hz| Continuous Power
---|---|---|---
TPG-0850F-R
| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB| 850W
| Max Output Current| 22A| 22A| 70.9A| 0.3A| 3A
| Max Output Power| 120W| 850W| 3.6W| 15W
TPG-0750F-R
| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB| 750W
Max Output Current| 22A| 22A| 70.9A| 0.3A| 3A
Max Output Power| 120W| 750W| 3.6W| 15W
TPG-0650F-R
| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB| 650W
Max Output Current| 22A| 22A| 70.9A| 0.3A| 3A
Max Output Power| 120W| 650W| 3.6W| 15W

Installation Steps

Note: Make sure that your system is turned off and unplugged. Disconnect the AC power cord from your old power supply.

Open your computer chassis; please refer to the instruction manual provided with your chassis.
Install the PSU into the case with the four screws provided.
If your motherboard requires a 24pin Main Power connector, please connect the 24pin Main Power connector to the motherboard.
For motherboard that only requires a 4pin ATX 12V (CPU) connector, please detach a 4pin connector from the 4+4pin ATX 12V connector and connect it to the motherboard. (Either one of the 4pin from the 4+4pin ATX 12V connector will work)
For motherboard that requires a single 8pin EPS connector, please use the 4+4pin connector from the power supply.
Connect other peripheral power connectors to devices such as hard drives,optical drives, etc.
If your graphic card requires PCI-E power connector, please connect corresponding PCI-E connector instructed by your graphic card’s user manual. Please note the power supply utilizes an unique 6+2pin PCI-E connector that can be effectively used as a single 8pin or 6pin PCI-E connector. To use it as a 6pin PCI-E connector, please detach the 2pin connector from the 6+2pin connector.
Close your computer case and connect the AC power cord to the power supply AC inlet.
Attention! When Smart Zero Fan System is turned on, the fan will not operate until the power supply reaches approximately 20% of rated load; It is normal if the fan does not operate when computer is at a low working load.
This PSU is equipped with a patented 256 colors Riing 14 RGB Fan which features:
Five lighting modes
The lighting modes can be changed when the RGB lighting button is pressed. You can either choose RGB Cycle Mode, Solid Red/Green/Blue/White Mode or you can switch off the LED.
Built-in memory Automatically recovers the previous lighting mode after you restart the PSU.

Total Protection

Over Voltage Protection

Voltage Source	Protection Point
+3.3V	4.3Vmax.
+5V	6.5Vmax.
+12V	15.5Vmax.

Over Current Protection

P/N	TPG-0850F-R
Voltage Source	Protection Point
+3.3V	24.2A min. ; 35.2A max
+5V	24.2A min. ; 35.2A max.
+12V	77.99A min. ; 113.44A max.

Short Circuit Protection
Activated when any DC rails short circuited.
Over Power Protection The power supply shall be shut down and latch off, if the wattage of the power supply is 110% – 160% over continuous power.

EMI & SAFETY

EMI Regulatory & SAFETY Standards

OUGHPOWER GRAND RGB 850W/750W/650W GOLD| CE, cTUVus, TUV SOD, FCC, EAC, CCC and BSMI certified.

Environments

MEOperating temperature	1 0°C to +50°C 1IM
Operating humidity	20% to 90%.non-condensing
M—MTBF	r > 120,000 hours

Trouble-Shooting

If the power supply fails to function properly, please follow the troubleshooting guide before application for service:

Is the power cord plugged properly into electrical outlet and into the power supply AC inlet?
Please make sure the I/O switch on the power supply is switched to I position.
Please make sure all power connectors are properly connected to all the devices.
If connected to a UPS unit, is the UPS on and plugged in?

If the power supply is still unable to function properly after following the above instruction, please contact your local store or Tt branch office for after sales service. You may also refer to Thermaltake’s website for more technical support: thermaltake.com