Tyba Turn 2 Smart Touch User Guide

User Guide

Turn 2
TY-K-TURN

Turn 2 Smart Touch

DISCLAIMER
Tyba Home Limited makes no representations or warranties with respect to this manual and, to the maximum extent permitted by law, expressly limits its liability for breach of any warranty that may be implied to the replacement of this manual with another. Furthermore, Tyba Home Limited reserves the right to revise this publication at any time without incurring an obligation to notify any person of the revision.
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Tyba Home Limited nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information that is contained herein. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us.
All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to help ensure compliance with documented system data, only the manufacturer shall perform repairs to components.
Failure to observe this information can result in injury or equipment damage.
Copyright © 2022 by Tyba Home Limited All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher. For permission requests, write to the publisher, addressed “Attention: Permissions Coordinator,” at the address below.
Tyba Home Limited, Unit 3, Jubilee Way, Faversham, Kent, ME13 8GD, UK +44 (0) 20 3907 6877 www.tybahome.com
TRADEMARKS
Tyba Home Limited has made every effort to supply trademark information about company names, products and services mentioned in this manual. Trademarks shown below were derived from various sources. All trademarks are the property of their respective owners.
General Notice : Some product names used in this manual are used for identification purposes only and may be trademarks of their respective companies.
Product Modifications

Document Revisions

Preface

1.1 Description of the User
This User Guide is intended for professional installers such as electricians or system integrators.
1.2 Explanation of Safety Warnings
Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury
Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Indicates information considered important, but not hazard-related.
1.3 Retaining Instructions
Read and understand this manual and its safety instructions before using this product. Failure to do so can result in serious injury or death.
Ensure that each person who uses the product has read these warnings and instructions and follows them.
Tyba Home Limited is not liable for cases of material damage or personal injury caused by incorrect handling or non-compliance with the safety instructions. In such cases, the warranty will be voided.

Product Description

2.1 Intended Use and Reasonably Foreseeable Misuse
Turn 2 is intended to be used as a room controller to adjust environment parameters such as lights, climate, shades and AV. Turn 2 is not intended to be used for any function outside those described.
Turn 2 should be used with the following software, original accessories and components only:

• Tyba IOS & Android applications.
• Tyba genuine accessories such as Bus Connectors, wall plates or stands.
• Tyba control system drivers or third party API.

2.2 System Overview
Turn 2 is a room controller designed to adjust room parameters with a rotating outer ring. Turn 2 also features a touch screen used to switch between control functions.
Turn 2 can be used either stand alone, powered by USB C or with one of the optional Bus Connectors. The Bus Connectors are designed to provide a mounting interface, power and optional system integration.
2.3 Technical Data

2.4 Product Compliance
This product complies to all relevant Directives associated with CE, UKCA, IC & FCC.
The Declaration of Conformity and further certification documentation can be found at www.tybahome.com/downloads. The Product is in conformity with the following relevant product safety standard:

• BS EN IEC 62368-1

Safety Instructions

Read and understand this manual and its safety instructions before using this product. Failure to do so can result in minor or moderate injury.
3.1 How to Use the Product Safely
When using this product, ensure all guidance is followed regarding technical specification, installation, setup and operation. Never use this product with anything other than Tyba genuine accessories.
3.2 Graphical Symbols

the product complies.
| The UKCA Marking on the product is the manufacturer’s declaration that the product complies.
| The FCC Marking on the product is the manufacturer’s declaration that the product complies.
| The WEEE Marking on the product is the manufacturer’s confirmation that the product is not recyclable.

Installation

The product should only be installed by a qualified and trained person.
4.1 Connections and Physical Details

4.2 Mounting to a Bus Connector
Turn 2 mounts to the Bus Connector range using a magnetic mounting system. Once the Bus Connector is installed, align Turn 2 with the front of the Bus Connector ensuring that the mounting locators on both Turn 2 and the Bus Connector are the right way around. Slowly move Turn 2 towards the Bus Connector until the magnets engage. Before releasing ensure Turn 2 is correctly seated on the Bus Connector.

Setup

It is recommend that setup is carried out by a qualified and trained person.
5.1 Powering On
Once Turn 2 is powered using a Bus Connector or USB C, the display will turn on and the device will begin to start up. If the device is new and has not been setup before, it will automatically go in to setup mode as below.

TY-K-TURN-93idje393jd9e | 3id939jdejde9w.f

5.2 Connecting
To setup Turn 2 you will need to download the Tyba app for IOS or Android. Within the Tyba app, press + or the “add a device” button. Scan the QR code presented on the Turn 2 display to start the setup process. Once the Tyba app has connected to the device follow the steps:

• Choose a friendly name for the device. If you don’t enter one it will default to “Turn 2”
• Select a Wi-Fi network from the list
• Enter the password for the selected Wi-Fi network
• The device will now be added to your local network
• Choose “Setup Later”

A Wi-Fi network with DHCP enabled is required for initial setup. Ensure good Wi-Fi signal strength for reliable operation.
5.3 Settings

Now that you have added the device to the Tyba app, it will be shown in the devices list. Next to each device is a traffic light status indicator.

• Choose the device from the list, it should have an amber status indicator as setup has not been completed
• You will be taken to the devices settings menu

If you selected to “Setup Now” during section 5.2 you will have been taken directly to the devices settings menu.
The settings available on the device are as follows:

check/install software updates
Date & Time| The date and time of the device, select from automatic or manual
LED| Enable or disable the LED
Clicker| Enable or disable the audible click
Motion| Enable or disable the motion detector
Display Sleep| Change the period until the device sleeps
Screensaver| Choose a screensaver

5.4 Wi-Fi Network
You can change or modify the network settings of the device after the initial setup described in section 5.2. The options are as follows:

5.5 Control Elements
The control elements presented on Turn 2 are configured under the device settings menu of the Tyba app. The controls interface provides a flexible method for building the control options required for your specific application. The options are as follows:
Lights

Choose per light if it is dimmable or switched.

Climate

Provide the operating temperature range, increment and temperature source, e.g. Internal or External. If set to Internal, choose between C or F and optionally provide a temperature offset
Fan| Configure control of up to 8 fan speeds
Humidity| Configure display of humidity and control set point.
Provide the operating humidity range
Modes| Configure control of up to 8 modes
Information| Configure display of Air Quality, Air Pressure and
Humidity

Shades

Choose per shade if it is a position or open/close shade

AV

controls and metadata

By default control elements will appear in a predetermined order for consistency.
However, the order in which the controls appear on the device can be changed by dragging and dropping the sections of the control interface within the Tyba app to reflect the desired order.
5.6 Reset, Remove and Report Error

device will be reset back to default.
The devices network settings will remain.  You can also press and hold the device in the device list to bring up the remove and reset menu.
Remove| In the device settings menu scroll to the bottom and choose remove. This will remove the device from the device list. You can also press and hold the device in the device list to bring up the remove and reset menu.
Report error to Tyba Support| If you are experiencing a technical issue with Turn 2 and have contacted Tyba support you may be asked to provide additional information. Use the report feature to set Tyba support technical logs.

5.7 Add Existing Devices to the Tyba app
To add a device that has already been setup to the Tyba app use the following steps:

• Press + or the “add a device” button
• Choose “Add Existing Device”
• The Tyba app will scan the network for existing devices and you will presented with the discovered devices.
• Select the devices you want to add and press the tick icon to finish.
• The devices will appear in the device list.

If no devices are found ensure the mobile device with the Tyba app installed is on the same Wi-Fi network as the device you intend to add.
5.8 Setup Mode
Should you need put the device back in setup mode for any reason, remove the device from the Bus Connector and power via USB C. Once the device has fully started up, press the button on the back of the device to enter setup mode and follow the steps in section 5.2.

5.9 Software Update
Keeping your device up to date with the latest software is simple. Use the following steps to check and install updates.

• Select a device from the device list
• Press the settings icon to enter device settings menu
• Press on the Software section within settings. The device will now check if there are any updates available
• If there is an update, press “Update Now” to start the upgrade. Status of the process will be presented with the Software section. The device will reboot once the update has been installed.

In the very unlikely instance where an update fails or causes any issues, you can roll back to the previous version using the following steps:

• Remove the device from the Bus Connector
• Press and hold the button on the back of Turn 2
• Connect a USB C power source
• Continue to hold the button for 30 seconds
• The device will roll back to the previous version

Operation

6.1 User Interactions
Turn 2 has been designed around two key user interactions; rotation and touch.
Rotation always is used to control the selected parameter, e.g. temperature set point .
Touch is used to change what you are controlling.

6.2 Touch
Use the touch screen to swipe left and right between the configured primary controls, e.g. lights, climate, shades and media. These controls are signified by the paging dots at the bottom of the display. Once the primary control is selected, tap the display to cycle through the secondary control options, e.g. if lights was selected, tap the display to cycle through all of the available lighting related functions. Continue to tap and the control will cycle back to the start, or press and hold the display to go straight back to the primary control.
6.3 Rotation
Use the ring to control the parameter of the selected control, e.g. the temperature set point. The rotation input will behave differently depending on the selected control.
When a preset control is selected, such as light scenes or fan speeds the rotation will control which preset is selected between 1-8. When a control such as volume or a light is selected the rotation will alter the brightness or volume level in 0-100 increments.

Maintenance

The product is maintenance free. Repair should only be carried out by a qualified and trained person.

March 2023
Version 1.2

Documents / Resources

| Tyba Turn 2 Smart Touch [pdf] User Guide
Turn 2 Smart Touch, Turn 2, Smart Touch, Touch
---|---

References

• Tyba Home
• Resources — Tyba Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>