EMERSON 2.19F01 Update Advisory Supervisory Control Platform Firmware Instruction Manual

Update Advisory Supervisory Control Platform
Firmware 2.1 9F01

2.19F01 Update Advisory Supervisory Control Platform Firmware

Release Notes
A new general release version of the Supervisory controller firmware version 2.19F01 has been released and is available for customer upgrade. For more information, visit the Supervisory Control page on the Emerson website:
https://climate.emerson.com/en-us/products/controls-monitoringsystems /facility-controls-electronics/facility-and-system-controls/lumitysupervisory- controls-platform

Who Should Update

Emerson recommends that all customers upgrade their Supervisory controllers and PCs running Connect+ to the latest version to take advantage of the latest fixes and enhancements listed in Table 3.
All customers who use any of the features below are advised to upgrade to Supervisory controller 2.19F01, and customers using any of the features listed in Table 3.

CONNECT+ UPDATE REQUIRED

Table 1 – Supervisory Controller and Connect+ Compatibility Matrix
Supervisory controller version 2.19F01 requires Connect+ 1.5.3 or greater. It is recommended the latest version of Connect+ be installed for best practices. If communication with Connect+ is required, upgrade Connect+ to the latest version first, then update the Supervisory controllers. Contact Emerson for more information about upgrading.

CONTROLLER FIRMWARE COMPATIBILITY

Table 2 – Firmware Platform Mapping

Features and Fix Descriptions Supervisory| Supported in Controllers 2.19F01
---|---
Features|
Offline Programming – Limited Release

Allows the user to configure a Site Supervisor/E3 without the hardware through a web site.| ✓
Layout Manager
Users can n ow move views up and down within a panel and between other panels.| ✓
Floor Plan Match Check
After installation of a Floorplan, users can now check configuration with the Floorplan Match Info window (View and Edit privileges) to verify unit types are matched.| ✓
16AI Board Application
Sensor Units supports Ohms and Volts.| ✓
UI – Engineering Units
Differential (Delta) Pressure EU is supported.| ✓

Table 3 – Supervisory Controller 2.19F01 Feature and Fix Matrix

Features and Fix Descriptions| Supported in Supervisory Controllers 2.19F01
---|---
Fixes|
UI – Alarm Communications
>      The format of content in the Confirmation page is now correct when saving configurations for Recipients.

      Relays will not turn OFF when active alarms are still present.| √
UI – Graphing
>      Saved graphing points of other devices are no longer removed when leaving the app and then returning to the app.| ✓
UI – Floorplan
> The Floorplan Match Icon will now display.
Points value displayed correctly for non-gateway units when installing one floorplan with GsAppSummaryTable widget onto another peer network.
Floorplan remote point registration failure message no longer prompts error “No Memory or queue is full for registering points.”
Floorplan will now install correctly from USB.
GsTable – All points in the widget are now displayed if the first point cannot be found.
The floorplan now displays correctly when restoring a setpoint file to a different unit number.
Scroll bars are visible and able to scroll floorplans that are longer or wider than the screen.
The “GsAppSummary” widget for “Air Handlers (AHUs)” is no longer blank.
E2 AHU points’ status now display correctly when overriding.| ✓
General System Properties – Network Settings
> On the Network Settings page, if the DNS Server value is updated and tabs are switched by clicking the Localization tab, the DNS Server value will update correctly on the Confirmation page and when switching back to the Network Settings page.| ✓
Circuit Applications – Main Menu
> If no Circuit Applications are licensed, the Case Defrost Schedule Summary will not display.| ✓
UI Enhancements
•  Send to
>  Process bar and error message are will pop out as a separate window when sending to a point’s expanded information.
•  Layout Manager >  After clicking the “Clear Zooming” button on a graph, the graph time filters will no longer be cleared.
  When I added a new device/application for the graph after deleting the graph’s app, the preview will now display correctly.
•  Starting Process page
>  UI stayed in “Starting Process” page and will now be refreshed automatically after restore setpoint with enabled “Force SSL.”| ✓
Features and Fix Descriptions| Supported in Supervisory Controllers 2.19F01
---|---
Logs & Statistics – Audit Log
Thescheduleapplication name is no longer displayedasiid when selecting one schedule application from the Schedule drop-down list in Alarm Communications page.| ✓
System Summary Page
Word of Point name displayed in the System Summary page is no longer truncated.| ✓
System
•Air Velocity
Unit of air velocity c hanged from default of feet/minute to meters/second.| ✓
Peer Network – Alarm Communication
TheAlarm out displays correctly in the gateway unit when enabling ‘Alarm Annum for a non-gateway unit.| ✓
IPro DAC Application
Damper IAQ enhancements.| ✓
Air Handler Application
AHU compressor status can now control by Enable.| ✓
M400
The OUTPUT RPM value On SiteSupervisor is now consistent with the device.| ✓
Restore – UltraSite to Site Supervisor
• Standard Circuits
• Analog Sensor Control
• AHU Large
• Lighting > Various parameters for these applications will now restore correctly.| ✓
IMC Prodigy Application
ECON STATUS no longer reports incorrect values on the Input/Output Status tab.| ✓
File Management
After an .ADF has been uploaded. application/device type will now display.| ✓
Irrigation Application
If connected to Global Data at startup. the Irrigation Outdoor Temp value will nov.
update to NONE to match the Global Data value if also set to NONE.| ✓
Digital Sensor Control Application
The vistaility of Proof Type is now correct.| ✓
Lighting Application
The SUNDOWN parameter will now display correctly when connected to Global Data.| ✓

Table 3 – Supervisory Controller 2.19F01 Feature and Fix Matrix

Update Supervisory Controller firmware

For Emerson Digital Cold Chain Technical Support

•  833-409-7505
• ColdChain.TechnicalServices@Emerson.com

https://climate.emerson.com/en-us/products/controls-monitoring-systems /facility-controls-electronics/facility-and-system-controls/lumity- supervisory-controls-platform
cument Part # 026-4079 Rev 1
This document may be photocopied for personal use.
Visit our website at www.climate.emerson.com for the latest technical documentation and updates.
Join Emerson Technical Support on Facebook http://on.fb.me/WUQRnt
For Technical Support call 833-409-7505 or email ColdChain.TechnicalServices@Emerson.com
The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. Emerson reserves the right to modify the designs or specifications of such products at any time without notice. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user. ©2022 Emerson is a trademark of Emerson Electric Co.

MERSON. CONSIDER IT SOLVED.

Documents / Resources

| EMERSON 2.19F01 Update Advisory Supervisory Control Platform Firmware [pdf] Instruction Manual
2.19F01, 2.19F01 Update Advisory Supervisory Control Platform Firmware, Update Advisory Supervisory Control Platform Firmware, Advisory Supervisory Control Platform Firmware, Supervisory Control Platform Firmware, Platform Firmware, Firmware
---|---

References

• Log into Facebook | Facebook
• Copeland | Copeland US
• Lumity Supervisory Control Platform | Copeland US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>