milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit Instruction Manual

June 12, 2024
Milwaukee

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit Instruction Manual

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit Instruction
Manual

IMPORTANT SAFETY INSTRUCTIONS

READ ALL SAFETY WARNINGS, INSTRUCTIONS, ILLUSTRATIONS AND SPECIFICATIONS PROVIDED WITH THIS POWER TOOL. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVE THESE INSTRUCTIONS – THIS OPERATOR’S MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS.

  • Do not modify the plug.
  • Chemical Burn Hazard. Keep coin cell battery away from children.
  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  • If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.

SYMBOLOGY

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit -
SYMBOLOGY

SPECIFICATIONS

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit -
SPECIFICATIONS

FUNCTIONAL DESCRIPTION

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit - FUNCTIONAL
DESCRIPTION

ASSEMBLY

To reduce the risk of injury, always unplug tool before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous.

Pairing

If remote is not connected to the adapter, pairing can be setup by:

  1. Insert Adapter into an outlet. NOTE : To confirm the Adapter has power, the power light indicator will light for 1 second.
  2. Press button on the Adapter and the remote until both LED’s begin to flash. A steady green light on both Adapter and remote will confirm that the unit is paired. NOTE : Remote needs to be within close proximity to ensure remote is receiving signal from the Adapter. This procedure will time out in 30 seconds if tool is not paired and will enter standby mode for inactivity.

To confirm that the remote has paired with the Adapter successfully, press button on remote and the button will light. Multiple remotes can be paired to one Adapter.

Unpairing

  1. Press and hold button on remote until the LED has a flashing red light.
  2. Press and hold button on Adapter until the pairing indicator LED has a flashing red light.

This procedure will time out in 30 seconds if remote and Adapter are not paired. It will enter standby mode for user inactivity

Remote Strap

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit - Remote
Strap

Remote strap installation:

  1. Feed logo side of strap through inner side of remote housing.
  2. Fold strap over and press firmly.
  3. Feed tail end of strap through the outer side of remote housing.
  4. Fold strap over and press firmly.

To adjust the length of the strap, release velcro and pull snug.

Remote Belt Clip

milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit - Remote Belt
Clip

  1. To remove the belt clip, remove the screw from the back of the remote.
  2. Pull the belt clip away from the remote.
  3. To install the belt clip, line up the tabs on the clip with the notches on the back of the remote.
  4. Insert the screw and tighten securely

GENERAL USE AND CARE

Use proper tools rated for this device. Others may be hazardous.

  1. Insert Adapter into wall outlet. Confirm power indicator flashes and pairing indicator is lit.

  2. Plug corded tool into Adapter outlet.
    NOTICE Do not use with a tool that requires input current greater than 12 A. It could result in damage to the adapter.

  3. Using remote, press the power button to turn ON/OFF tool.
    NOTE : Ensure tool being used is ON and fully operational.

MAINTENANCE

Internal Remote Battery

Chemical Burn Hazard. This device contains a lithium button/coin cell battery. A new or used battery can cause severe internal burns and lead to death in as little as 2 hours if swallowed or enters the body. Always secure the battery cover. If it does not close securely, stop using the device, remove the batteries, and keep it away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention.

An internal battery is used on the remote to facilitate full functionality.

To replace the battery:

  1. Remove strap or the screw on the belt clip.
  2. Remove the screw and open the battery door.
  3. Remove the old battery, keep it away from children, and dispose of it properly.
  4. Insert the new battery (3V CR2032), with the positive side facing up.
  5. Close the battery door and tighten the screw securely.
  6. Reattach the strap or screw with belt clip.

Internal Fuse Failure

If the power button on the remote is pressed and the power indicator starts flashing on the plug, there is an internal fuse failure making the tool unusable. Please contact 1-800-SAWDUST or visit milwaukeetool.com for service.

ACCESSORIES

Use only recommended accessories. Others may be hazardous.
For a complete listing of accessories, go online to www.milwaukeetool.com or contact a distributor.

WIRELESS COMMUNICATION

Pursuant to part 15.21 of the FCC Rules, you are cautioned that changes or modifications not expressly approved by the party responsible for com-pliance could void your authority to operate the product.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules and ISED-Canada’s license exempt RSS standards. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

SERVICE – UNITED STATES

1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM – 6:30 PM CST
or visit www.milwaukeetool.com

Contact Corporate After Sales Service Technical Support with technical, service/repair, or warranty questions.
Email: metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at www.milwaukeetool.com to receive important notifications regarding your tool purchases.

SERVICE – CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM – 4:30 PM CST
or visit www.milwaukeetool.ca

MILWAUKEE TOOL
13135 West Lisbon Road • Brookfield, WI 53005 USA

Documents / Resources

| milwaukee 0950-20 Wireless Dust Control Adapter and Remote Kit [pdf] Instruction Manual
0950-20, 0951-20, 0950-20 Wireless Dust Control Adapter and Remote Kit, Wireless Dust Control Adapter and Remote Kit, Dust Control Adapter and Remote Kit, Adapter and Remote Kit
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals