Starwell Technology PE10DA 14.7W DALI Dimmable LED Driver Instruction Manual

June 12, 2024
Starwell Technology

Starwell Technology logo Technology PE10DA 14.7W DALI Dimmable LED Driver
Instruction Manual

Features:

  • Standard DALI dimming interface
  • with PUSH function to realize PUSH dimming
  • Output flcker free
  • International universal AC input voltage (100V to 265VAC)
  • Protections: shoet circuit/over voltage/overcurrent
  • Natural cold wind
  • Big terminal locked by screw
  • Suitable for LED home lighting and commercial lighting
  • Safe no load protection device
  • Economic and convenient installation
  • Conform to the world lighting equipment safety standards
  • Protection class II
  • Three years warranty

Starwell Technology PE10DA 14.7W DALI Dimmable LED Driver - icon
1

General description:

DALI Dimming LED Driver is one of the constant current dimming LED driver developed by my company with high power factor. high efficiency. high precision. the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise. long life and other chorocteristica.
DALI Dimming LED Driver use standard DALI signal interface, can match with ail DALI control system in the market.
DALI full name: Digital Addressable Lighting Interface.

Specification:

Model PE1ODA24 PE10DA42 PE1ODA09
OUTPUT Output Voltage 9-24Vdc 9-42Vdc
Non-load Output Voltage 30Vdc 49.5Vdc 12Vdc
Output Current 350/400/450/500mA 200/250/300/350mA 400/500/600/700mA
Output Power 2.7W∼12W 1.8W-14.7W 1W-6.3W
Strobe Level No Flicker
Dimming Range 0∼100% , LEDstart at 0.03%possible.
PWM Dimming Frequency =3600Hz
Current Accuracy ±3%
Ripple & Noise flV (No dimming)
INPUT Dimming Interface DAL! (IEC62386), Push DIM
Input Voltage Range 100-250Vac
Frequency 50/60Hz
Input Current <0.06A <0.07A <0.07A
Power Factor PF>0.99/100Vac, at full load PF>0.99/100Vac, at full load

PF>0.9/100V ac, at full load
THD| 230Vac@THD 1.57,3 (full load)
Efficiency(typ.)| 82.%| 86.%| 83%
Inrush Current(typ.)| Cold start 0.6A@230Vac| Cold start 0.7A@230Vac| Cold start 0.7A@230Vac
Anti Surge| L-N: 2kV
Leakage Current| <0.98mA/230Vac
BWRONNENT| Working Temperature| ta: 45°C tc: 80°C
Working Humidity| 20 ∼ 95%RH, non-condensing
Storage Temp., Humidity| -40 ∼ 80°C 10∼95%RH
Temp. Coefficient| ±0.03%/t(0-50)°C
Vibration| 10-500Hz, 2G 12min./lcycle, period for 72min. each along X, Y, Z axes.
PROTEC11ON| Over-heat Protection| Intelligently adjusting or turning off the output current if the PCB temperature a110°C„ auto recovers.
Over Load Protection| Shut down the output when rated powera102%, auto recovers.
Short Circuit Protection| Shut down automatically if short circuit occurs, auto recovers.
Non-load Protection| Shut down automatically if short circuit occurs, auto recowers.
SAFETY| Withstand Voltage| I/P-0/P: 3750Vac
Isolation Resistance| I/P-0/P: 100MO/500VDC/25°C/70%RH
Safety Standards| IEC/EN61347-1, IEC/EN61347-2-13
Strobe Test Standard| IEEE 1789
OTHERS| Dimension| 105x39x26mm(LW$H)
Packing| 106x40x26.5mm(L
W*H)
Weight(G.W.)| 689±10g

Dimensions:

Starwell Technology PE10DA 14.7W DALI Dimmable LED Driver - Fig
1

Product Label:

Starwell Technology PE10DA 14.7W DALI Dimmable LED Driver - fig
2

LED Current Selection:

DIP switch for 4 optional currents’ quick selection( see the table below ).

PE I ODA24| DIP Switch| | | |
---|---|---|---|---|---
Output Current| 350mA| 400mA| 450mA| 500mA
Output Voltage| 9-24V| 9-24V| 9-24V| 9-24V
Output Power| 3.15W-8.5W| 3.6W-9.6W| 4.05W-10.8Vv| 4.5W-12W
PE I ODA42| DIP Switch| | | |
---|---|---|---|---|---
Output Current| 200mA| 250mA| 300mA| 350mA
Output Voltage| 9-42V| 9-42V| 9-42V| 9-42V
Output Power| 1.8W-8.4W| 2.25W-10.5W| 2.7W-12.6N| 3.15W-14.7N
PE 1 ODA09| DIP Switch| | | |
---|---|---|---|---|---
Output Current| 400mA| 500mA| 600mA| 700mA
Output Voltage| 2-9V| 2-9V| 2-9V| 2-9V
Output Power| 1W-3.6W| 1W-4.5w| 1.2W-5.4W| 1.4W-6.3W

  • After current setting by DIP switch, power off and then power on to make the new current effective.
  • E.g. LED 3.2V/pcs: 9-24V can power 3-7pcs LEDs in series, 9-42V can power 3-12pcs LEDs, the max quantity of LEDs in series will be subject to the actual voltage of LED.

Wiring Diagram:

Starwell Technology PE10DA 14.7W DALI Dimmable LED Driver - fig
3

Push Dimming:

On/off control: Short press.
Stepless dimming: Long press.
With every other long press. the light level goes to the opposite direction.
Dimming memory: Brightness will be the same as previously adjusted when turning off and on again.

Wiring:

The input terminal: wire gauge 22AWG-14AWG (0.315mm2 – 2.06mm2)wire stripping requirement:9-10mm
The output terminal: wire gauge 22AWG-12AWG (0.315mm2 – 3.15mm2)wire stripping requirement :6-7mm.

Relationship Diagrams:

Starwell Technology PE10DA 14.7W DALI Dimmable LED Driver - fig
5

The use of guidance:

Unless otherwise specified, all specifications and parameters are measured at 230VAC input. rated load and 25 °C Ambient Temperature
This product has a press line cap at the input, with self-locking clamping, it can be opened up with a screwdriver, then you will see the input terminal connected with the AC line L and the null lime N. The output terminal connect a according to the product label, notice the positive and negative pole.
l :please pay attention to the distinction between input and out put , connect correctly, then power on
2:please connect first the load of the DC output, open the driver after checking; in the constant current mode, if power on at open circuit, please turn off the driver and can’t connect the LED until the electric energy stored by the output release. or it may damage the LED;
**3.this type of driver is only limited to the use of the LED lamps ,the input voltage range is AC I 00-250V,the heat insulation cotton and other items that obstruct the heat dissipation of the product. which conforms to the product under the specified output voltage, current range. the use environment temperature is -20-45 degrees. and the surface can not cover the conditions of the environment, this product enjoys three years of free warranty. I .the LED lamp doesn’t bright after the dimming driver is connected at the first time. please turn off the AC input and check as follow:

  1. whether or not DC output bad contact;
  2. whether DC output polarity is reversed, or the LED board is welded anti;
  3. whether AC input is bad contact, test after eliminating these failures;
    2.the device has good connection. LED lights, but the LED flicker, please turn off the AC input and check as follow:
    1).whether or not the parameters and actual parameters match.
    2).please timely communicate with us if you have any questions in the using. we will try our best to solve the problems with you.

The abnormal conditions and the corresponding treatment methods:

Digital Addressable lighting Interface (DALI) DALI slave unit will send data only master unit requests. that is. adopt command answering mode There are 64 slave units at most in the same DALI network, each unit has a separate address(short address). A salve unit can also be assigned to a certain group. and a slave unit can belong to different group. salve unit can exist up to 16 groups at the same time. each unit can set 16 scenarios. The main features of the DALI protocol

  1. Asynchronous serial communication.
  2. 1200 baud rate. using the Manchester encoding format.
  3. Two lies differential signal.
  4. The high level when differential voltage is larger than 9.5V.
  5. The low level when differential voltage is less than 6.5V.
  6. The master unit controls communication process.
  7. One DALI bus can connect with 64 slave units.
  8. Each slave unit can be individually addressed.

DALI Electrical Specification
Under the idle state. from machine unit method to control the bus :

  1. High Output power at ordinary time. not to interference in the hold signal.
  2. Output low electricity at ordinary time. directly to the DALI bus short circuit to each other.
  3. DALI bus maximum current of 250mA 4)Not a two-way communication at the same time.

Statement:

The pictures and specifications is for reference only. in kind prevail, specifications are subject to change with further notice.

Starwell Technology logoDALI Dimming LED Driver (Constant Current)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals