Pyle PCM20A Compact Mini Home Power Amplifier User Manual

Pyle PCM20A Compact Mini Home Power Amplifier

IMPORTANT SAFETY INSTRUCTIONS

1. Read Instructions — All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions — The safety and operating instructions should be retained for future reference.

3. Heed Warnings — All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions — All operating and use instructions should be followed.

5. Water and Moisture — The appliance should not be used near water -for example, near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool, or a wet basement.

6. Ventilation — The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings: or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

7. Heat — The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances
   (including amplifiers) that produce heat.

8. Power Sources — The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

9. Grounding or Polarization — Precaution should be taken to insure that the grounding or polarization means of an appliance is not defeated.

10. Power-Cord Protection — Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the appliance.

11. Cleaning — The appliance should be cleaned only as recommended by the manufacturer.

12. Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

13. Nonuse Periods — The power cord of the appliance should be unplugged from the outlet when the appliance is to be left unused for a long period of time.

14. Object and Liquid Entry — Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

15. Carts and Stands — If the appliance is used with a cart or stand, the cart or stand should be a type recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces cause the appliance and cart combination to overturn.

16. Mounting — The appliance should be mounted only as recommended by the manufacturer.

17. Damage Requiring Service — The appliance should be serviced by qualified service personnel when:

    • The power-supply cord or plug has been damaged.
    • Objects have fallen into, or liquid has been spilled into the appliance enclosure.
    • The appliance has been exposed to rain.
    • The appliance has been dropped, or the enclosure damaged.
    • The appliance does not appear to operate normally or exhibit a marked change in performance.

18. Servicing — The user should not attempt to service the appliance beyond that described in the user’s operating instructions. All other servicing should be referred to qualified personnel.

19. Overloading — Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

20. Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

21. Safety Check — Upon completion of any service or repairs to this appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operating condition.

Your new PYLE HOME PCM Amplifier

gives you the power and versatility that you need in a professional sound system. The wide frequency response is perfect for the amplification of vocals and music. The talk over function for the Mic 1 and Aux Input located on the front panel makes it perfect for meeting halls, auditoriums, sports events, schools, and office paging systems. Great for anywhere you need to deliver a special announcement with excellent sound quality.

FEATURES AND CONTROLS – FRONT PANEL

1. Power On/Off and Indicator
   Main power switch, the indicator light when the amplifier is turned on.

2. MIC1, MIC2, and AUX Volume Controls
   Adjust the output signal level of the corresponding inputs.

3. BASS and TREBLE Tone Controls
   Adjust the bass and treble of the corresponding inputs.

4. MIC1 and MIC2 Inputs
   To connect the low impedance microphone with a 1/4″ plug. The MIC 1 is a ” Priority” source, the signals from AUX will be attenuated automatically by -40dB, and the signal from MIC 1 will override to page (auto talk-over). it is good for a paging system.

5. AUX Input
   To connect the high-impedance audio source such as Tape Deck, CD player, or Tuner with a 1/4″ plug via an audio plug adapter (two phono RCA plugs into a 1/4″ mono jack).

6. BT/LINE Input Switch (For PCM21BT only )
   Press in, its Bluetooth Input status, and press it out, its LINE input status.

7. Bluetooth Indicator
   

8. Bluetooth Antenna (For PCM21BT only)
   The antenna is the best receiver for Bluetooth signals.

9. Voltage Switch
   This PA amplifier has a selectable input voltage from 110V/60Hz ( the standard in USA and CANADA ) to 220V/50Hz ( for EUROPEAN operation). Please make sure the switch is in the proper position before operating, otherwise severe damage will be incurred and not covered by warranty.

10. AC Input
    Plug the included power cord into the unit while the power is switched off, then plug the AC power cord into a proper power outlet. Please also replace the fuse only with the proper rating if needed (see the fuse rating of T 1.2AL 250V for 110-120V and T0.63AL 250V for 220V/240V printed at the power inlet)

11. Speaker Connection
    One or more speakers (4,8 or 16 Ohms) can be connected to the amplifier with or without transformers. However, before you connect any speakers to the amplifier, the total impedance must be calculated in order to avoid damage to the amplifier. A total speaker impedance greater than 8 Ohms or less than 8 Ohms can cause this damage to occur.

SPEAKER CONNECTION

One or more speakers (4, 8, or 16 Ohms) can be connected to the amplifier with or without transformers. However, before you connect any speakers to the amplifier, the total impedance must be calculated in order to avoid damage to the amplifier. A total speaker impedance greater than 8 Ohms or less than 8 Ohms can cause this damage to occur.

SYSTEM 1: Single Speaker System

NOTE: Connect the speaker (+) to the amplifier’s 8-Ohm terminal.

SYSTEM 2: Two (or more) Speakers in Series

NOTE: Connect the speaker (+) to the amplifier’s 8-Ohm terminal, depending on the TOTAL IMPEDANCE of the two speakers. If each speaker has an impedance of 4-Ohm, the total speaker impedance in this series configuration is 8 ohms.

SYSTEM 3: Two (or more) Speakers in Parallel

NOTE: Connect the speaker (+) to the amplifier’s 8-Ohm terminal, depending on the TOTAL IMPEDANCE of the two speakers. If each speaker has an impedance of 16-Ohm, the total speaker impedance in this series configuration is 8 ohms.

SYSTEM 4: Four Speakers in Series and Parallel

NOTE: Although the description above is for connecting two series pairs of 8 Ohms speakers in a parallel hook-up, you may also select to combine a series pair and a parallel pair in a parallel hook up, simply be sure you have calculated the total impedance, and attach the speaker (+) circuit wire to the proper amp terminal.

SYSTEM 5: Connecting Speakers with Transformers

NOTE: When the 25V or 70V constant line voltages are used, a line- matching transformer must be used with each speaker, All transformers must be connected in parallel, never connect line transformers in series.

BLUETOOTH OPERATION INSTRUCTION (For PCM21BT only)

External devices which have a built-in Bluetooth feature can be connected to this amplifier wirelessly to play through the amplifier’s speakers. If your amp is connected to speakers, you will hear audible tones which will help for connecting.

1. First, be sure that the amplifier is powered on, and turn the volume to low. Please remember to connect the Bluetooth Antenna at the back panel for a better-receiving signal
2. Press the BT/Line button switch in on the front panel, and you will hear the voice “POWER ON” and also “PAIRING”, and then the unit is automatically ready to pair with your external device.
3. Turn on the Bluetooth of your external device.
4. Search for available Bluetooth devices and make sure to be within range of your amp, and wait for your device to select “BT-RY” on the pairing devices lists of Bluetooth networks.
5. Once connecting you will hear a voice say, “Your Device is Connected”, then the Bluetooth pairing is successful and you have established a Bluetooth connection.
6. You can now play music on your external device through the amplifier.

Input Impedance

• AUX……………………………………………….. 150mV/50k-Ohm
• MIC 1/MIC 2………………………………………………1.0mV/600-Ohm
• Max Output Power…………………………………………….40 Watts x 1
• THD at rated output power………………………….1% or less at 1 kHz
• Frequency Response +/- 3 dB………………………….50 Hz to 15 kHz

Signal-to-Noise Ratio A-Weighted

• MIC………………………………………………………………………..61dB
• AUX……………………………………………………………………….72dB
• Speaker Outputs………. …………8-Ohm, 25V, and 70V line outputs
• Attenuation Level (MIC 1)…………………………………………….40dB

Tone Controls

• Treble………………………………………………………+/- 10dB, 10 kHz
• Bass………………………………………………………..+/- 10dB, 100 Hz
• Power Requirement……………………120V AC 60Hz/230V AC 50Hz
• Power Fuse…………………………….T 1.2AL 250V for 110-120V and T 0.63AL 250V for 220-240V
• Dimensions, inches (mm) WxHxD………………….7.87 x 3.15 x 5.90 (200 x 80 x 150)
• Weight, lbs (kg) ………………………………………………….4.5 ( 2.04)

FREQUENTLY ASKED QUESTIONS

What is the Pyle PCM20A Compact Mini Home Power Amplifier?

The Pyle PCM20A is a compact mini home power amplifier designed to enhance the audio performance of small speaker systems.

What are the dimensions of the PCM20A amplifier?

The exact dimensions may vary, but it is typically a compact unit measuring around 5.5 inches (width) x 4.2 inches (depth) x 2.7 inches (height).

What is the power output of the Pyle PCM20A?

The Pyle PCM20A usually provides a power output of around 2 x 20 watts RMS.

What type of speakers can I connect to this amplifier?

The Pyle PCM20A is generally compatible with most passive speakers rated within its power range.

How many audio inputs does the PCM20A have?

The amplifier typically features multiple audio inputs, including RCA and 3.5mm AUX inputs.

Does it have an output for headphones?

No, the Pyle PCM20A usually does not have a headphone output.

Can I use this amplifier for outdoor speakers?

Yes, you can use the PCM20A for outdoor speakers as long as they are passive and within the power range supported by the amplifier.

Does the PCM20A support a subwoofer output?

As of my last update, the Pyle PCM20A does not have a dedicated subwoofer output.

What is the power source for the amplifier?

The Pyle PCM20A typically operates using a standard AC power source.

Does the amplifier come with a remote control?

The inclusion of remote control may vary based on the package. Some versions may include a remote, while others may not.

Can I use this amplifier with my TV?

Yes, you can connect the PCM20A to your TV's audio output to enhance the sound quality of your TV's speakers.

Does the Pyle PCM20A have tone controls (bass/treble adjustments)?

Yes, it usually includes basic tone control adjustments for bass and treble.

Is the amplifier compatible with turntables?

Yes, the PCM20A typically supports turntables with a built-in phono preamp or when used with an external phono preamp.

Can I bridge the channels on this amplifier to create a mono setup?

No, the Pyle PCM20A is not designed to be bridged for mono operation.

Is the PCM20A suitable for powering bookshelf speakers?

Yes, the PCM20A is commonly used to power bookshelf speakers for small audio setups.

DOWNLOAD THE PDF LINK:Pyle PCM20A Compact Mini Home Power Amplifier User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>