DIGITUS DN-95357 Gigabit PoE Switch Installation Guide
- June 12, 2024
- DIGITUS
Table of Contents
DIGITUS DN-95357 Gigabit PoE Switch
Introduction
DN-95357 has a CCTV function for 250 meters of ultra-long-distance transmission. Users can choose to turn on or off the CCTV function. Improve network security and restrain network storms, facilitate management and maintenance, and meet the networking and access requirements of enterprises, communities, and hotels. office networks, and campus networks.
Main Features
- Support IEEE802.3 at standard, compatible with IEEE802.3 af by electrical equipment (PD)
- Stand-up output power up to 30W
- Support IEEE802.3 x full duplex flow control and Backpressure half duplex flow control
- Panel lights to monitor the working state and help with fault analysis
- Perfect security mechanism
- Line-speed forwarding intelligent identification
- Support CCTV Function
- Support Energy-Efficient Ethernet (EEE) function (IEEE802.3az)
- Support PD-ALIVE function
Package Contents
- PoE Switch
- User Guide
- Power Cord
Product Specification
Technical
Interface| 10＊10/100/1000Mbps auto-negotiation RJ45 port
PoE port| 1 ~ 8
PoE stand| IEEE802.3af/at
PoE total| 60 W
Power supply| 65 W
Key function| CCTV
PoE port output| Max 30W
RJ45 PoE power supply| Mode A, Anode 1/2,
Cathode 3/6
Indicator| PWR (Green), LNK/ACT (Green)
PoE (Orange)
Network media| 10 BASE-T: UTP category 3,4,5 cable (≤100m),
100 BASE-TX: UTP category 5, 5e cable (≤100m),
1000 BASE-T: UTP category 5,
5e cable (≤100m)
MAC Address Table| 2K, Automatic study,
automatic updates
Jumbo frame| 9216 Bytes
Packet buffer| 2Mbit
Transfer Mode| Store-and-forward
Packet Forward Speed| 14.88Mpps
Bandwidth| 20Gbps
Device Dimension| 168 x 93 x 32mm
Green energy saving| Support IEEE (802.3az)
Mains input| 100 ~ 240V AC, 50/60Hz
Operating Temperature| 0°C ~ 40 °C
---|---
Storage Temperature| -40 °C ~ 70 °C
Operating Humidity| 10% ~ 90% non-condensing
Storage Humidity| 5% ~ 90% non-condensing
Surge Protection| Common mode ± 2KV,
differential mode ± 1KV
MTBF| >50000 hour
Electrostatic standard| Contact ±6KV, air ± 8KV
Hardware Description
Front Panel
The Front Panel Consists of Ethernet Ports. The LED indicators are also
located on the panel.
DIP Switch: The DIP switch is located on the right of the panel.
Default: the factory default mode, can normal communication between ports
1~10.
CCTV mode: 1-8 ports can be isolated from each other, but 1-8 ports can
connect to 9, 10 ports after opening CCTV to stop broadcast storm to increase
the forwarding rate of the frame. The CCTV mode, up to 250m PoE distance
allows you to expand your network via Ethernet cable to where there is no
power line or outlet but where you want to fix devices such as IP Cameras.
Note: After changing the mode, there is no need to restart manually to make the corresponding configuration take effect.
LED indicator
LED
| ****
Color
| ****
Function
---|---|---
PWR| Green| Off: No Power supply.
Light: Indicates the switch has power.
LNK/ ACT
| ****
Green
| Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully established at 10/100Mbps.
Blink: Indicates that the Switch is actively
sending or receiving data over that port.
PoE
| ****
Orange
| Off: No PoE-powered device (PD) connected.
Light: There is a PoE PD connected to be port, which supplies power successfully. Blink: Indicates port abnormal power
supply.
Rear Panel
The rear panel of the PoE Switch indicates an AC inlet power socket, which
accepts input power from 100 to 240V AC, 50/60HZ.
Power socket
Connect the female connector of the power cord here, and the male connector to
the AC (Alternating Current) power outlet. Please make sure the voltage of the
power supply meets the requirement of the input voltage.
Grounding column
The switch already comes with a lightning protection mechanism. You can also
ground the switch through the PE (Protecting Earth) cable of the AC cord or
with Ground Cable.
Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions to avoid incorrect installation causing device damage and security threat.
- Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with a wet cloth or liquid;
- Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis;
- Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall;
- Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction;
- Make sure that the operating voltage is the same one labeled on the switch;
- To avoid the danger of electric shock, do not open the chassis without authorization;
Desktop Installation
- Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each corner of the Switch in case of external vibration. Allow adequate space for ventilation between the device and the objects around it.
Wall-mounted installation
- In the first two fixed screw on the wall as shown in the figure below. Aim at the two fixed hole switches (M4 screw, nut diameter 7mm) and the machine smoothly on the screw.
Turn on the switch
Please connect the AC power cord into the rear of the switch and to an
electrical outlet (preferably one that is grounded). When the switch is
powered on, the LED indicators flash momentarily for one second, which
represents a resetting of the system. The Power LED indicator turns on green.
Note: Please confirm the voltage is correct before powering on, otherwise the switch will be damaged. (The power input is: 100V-240Vac, 50/60Hz)
Disclaimer
- This is a Class A product. In a home environment, this product may cause radio interference.
- In this case, the user may be required to take appropriate measures.
- Hereby Assmann Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below-mentioned manufacturer address.
Assmann Electronic GmbH
- Auf dem Schüffel 3
- 58513 Lüdenscheid
- Germany
- www.assmann.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>