LANCASTER TABLE SEATING 164WAITRS4WL Walnut Waitress Station Instruction Manual
- June 12, 2024
- LANCASTER TABLE SEATING
Table of Contents
LANCASTER TABLE SEATING 164WAITRS4WL Walnut Waitress Station
PART LIST
-
/1PC Left Side Board SIZE: 31in x 22in
-
/1PC Right Side Board SIZE: 301in x 22in
-
/1PC Top Board SIZE: 24in x 23in
-
/1PC Kick Board SIZE: 24n x 3in\
-
/1PC Back Board SIZE: 36in x 24in
-
/1PC Shelf SIZE: 22in x 22in
-
/1PC Bottom Board SIZE: 22in x 22in
-
/1PC Shelf Bottom SIZE: 20in x 12in
-
/1PC Right Drawer Side SIZE: 12in x 4in
-
/1PC Left Drawer Side SIZE: 12in x 4in
-
/1PC Front Drawer Side SIZE: 24in x 4in
-
/1PC Back Drawer Side SIZE: 20in x 4in
HARDWARE LIST
-
A Cam Lock Screw (26PCS)
-
B Small Cam Lock (2PCS)
-
C Screws (12PCS)
-
D Shelf Pin (6PCS)
-
E Machine Screw (2PCS)
-
F Cam Lock (26PCS)
-
G Drawer Track (1PC)
-
H Handle (1PC)
TOOLS REQUIRED
- Phillip’s Head Screwdriver (not included)
ASSEMBLY INSTRUCTIONS
STEP 1.
Screw Cam Lock Screws (Ax16) onto side boards (1) & (2) and top board (3) and
back board (5). a. Attach tracks onto predrilled holes on side 1 and 2 using
the pilot holes to guide you.
STEP 2.
Insert cam lock (Fx18) into bottom Board (7), top board (3), side boards (1
&2).
Arrow on cam lock should face outer edge where screw will be inserted.
2a. Inset 2 cam lock screws (ax2) into piece 7
STEP 3.
-
Lay top Board (3) on ground. Add sideboards (1 &2): line up cam lock screw (Ax4) and cam lock (Fx4).
Tighten cam lock (Fx4) with screwdriver once boards are in place. -
Align bottom board (7) with remaining cam lock screws(A). Tighten cam locks with screwdriver.
STEP 4.
- Rotate the rectangle made in step 3 so that right side side (1) is touching the ground. Then place back board (5) onto the back side of the rectangular piece. Align the large cam lock screws (Ax8) in the corresponding holes. Tighten the cam lock (Fx5) with screwdriver.
- Place 2 small cam lock screws (Bx2) in the predrilled holes on the underside of bottom board (7).
STEP 5.
Align 2 screws (B) on bottom board (7) with holes on kickboard (4), press
kickboard onto screws.
STEP 6.
- Place 4 cam locks (Fx4) into back drawer (12) and Place 4 cam lock screws into front drawer (11)
- Place 2 cam locks and 2 cam lock screws into 9 and 10.
STEP 7.
Align all 3 panels of outside of drawer (10,12 and 9). Tighten cam locks.
a. Slide bottom of drawer (8) into notches.
b. Put piece (11) on front and tighten cam locks.
c. Attach handle (G) to predrilled holes on the front of board (11) with
(Cx2).
d. Attach tracks to the outside of piece 9 and 10
e. Insert drawer into tracks on assembled waitress station
STEP 8.
- Insert shelf pins (Dx6) on each side of the waitress station at desired height. place the shelf (6) on pins.
- Adjust drawer track to ensure tight fit if needed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>