TIBOR Billy Pate Anti Reverse Fly Reels Instructions

TIBOR Billy Pate Anti Reverse Fly Reels

Product Information

The Billy Pate Anti-Reverse Fly Reels are high-quality fishing reels that are lubricated at the factory prior to assembly. They come with a Drag Adjustment Knob and Drag Washer to provide smooth and controlled drag settings. The reels are designed for durability and reliability, ensuring a great fishing experience.

Maintenance:
After each fishing trip, it is recommended to perform the following maintenance steps:

1. Back off the Drag Adjustment Knob to release any pressure on the Drag Washer.
2. Rinse off the reel with fresh water.
3. Shake the reel dry.
4. Do not soak the reel.
5. Allow the reel to dry completely.
6. Store the reel in a protective pouch.

Service Tool Information:
A Service Tool is included with all new Billy Pate Reels. This tool facilitates spool changes or further takedowns, making it easier to maintain and repair your reel.

Disassembly/Reassembly:
Please follow the steps below for disassembling and reassembling your Billy Pate Anti-Reverse Fly Reel:

1. Remove the Handle Nut Screw (Part #26).
2. Remove the Handle Nut (Part #25) using the provided wrench. For left-hand reels, remove by turning clockwise; for right-hand reels, remove by turning counter-clockwise.
3. Back off the Drag Knob (Part #19). This will push the

Parts List:

*These are multiple-part components.

All replacement parts are available through your local Tibor dealer. A selection of replacement parts is also available for purchase online at tiborreel.com. When ordering parts, please specify the model name (Salmon, Bonefish, Tarpon) in addition to the complete part name and part number.

Billy Pate Anti-Reverse Fly Reels

MAINTENANCE
All reels are lubricated at the factory prior to assembly and relubrication is generally not necessary. After each fishing trip, back off the Drag Adjustment Knob to release any pressure on the Drag Washer. Simply rinse off the reel with fresh water and shake dry. Do not soak reel. Allow reel to dry completely and store in protective pouch.

SERVICE TOOL INFORMATION
A Service Tool is included with all new Billy Pate Reels. This Tool facilitates spool changes or further takedowns.

Features of the service tool include:

• A Wrench for the Star Nut over the Handle.
• A properly sized Screwdriver Blade to prevent screw head damage.

DISASSEMBLY/REASSEMBLY:
Please refer to the numbered parts list on the reverse side.

1. Remove Handle Nut Screw (Part #26).
2. Remove Handle Nut (Part #25) using the Wrench provided. For left hand reels, remove by turning clockwise; for right hand reels, remove by turning counter-clockwise.
3. Back off the Drag Knob (part # 19). This will push the Handle Arm (Part #22) off of the Main Gear. For left hand reels, remove the Drag Knob by turning clock- wise. For right hand reels, remove the Drag Knob by turning counter-clockwise. Note: the Handle Washer (Part #23) is under the Handle Arm, between the Drag Knob and the Handle Arm.
4. Remove the Drag Washers (Part #’s 16, 17 & 18) and the Drag Spring (Part #15). Note the order and position the Spring and Washers are in. They must be put back in the same order.
5. Remove the Spool. Check the Cork Drag Surface and lubricate if needed with Tibor Graphite Lube.
6. Reassembly is the reverse of disassembly. Put the Spool back on the reel, making sure it sits in the Frame properly.
7. Put the Drag Spring (Part #15) back on the Main Gear.
8. Put the Drag Washer (Part #16) on the Main Gear, smoothest side up.
9. Put the Teflon Washer (Part #17) on the Main Gear (this part should have a little lube on it).
10. Put the Keyed Drag Washer (Part #18) on the Main Gear. The tab slips into the keyway on the gear, with “bumps” facing up.
11. Put the Drag Knob (Part #19) on, lube the bottom side where the dimples ride against the Keyed Washer and tighten down almost all the way.
12. Put the Handle Washer (Part #23) on with the smooth side down towards the Drag Knob.
13. Put the Handle Arm (Part #22) on. This part may fit a little snug.
14. Put the Handle Nut (Part #25) on. For left hand reels, turn counter-clockwise, for right hand reels, turn clockwise. Tighten down with the Wrench provided until snug, then line up the notch in the Handle Nut with the hole for the Handle Nut Screw (Part #26). If the Handle Arm is not tight enough, tighten to the next notch in the Handle Nut. Use caution: if the Handle Nut is tightened too much, it can bind the reel.
15. Put the Handle Nut Screw (Part #26) on and back the drag off.

All replacement parts are available through your local Tibor dealer. A selection of replacement parts is also available for purchase online at tiborreel.com
When ordering parts, please specify model name (Salmon, Bonefish, Tarpon) in addition to complete part name and part number.

TCP-032/TB-024
| Main Gear (left hand)| XX-006-LH-AR| 21| Handle Knob| BP-021-XX
7| Clicker Spring| BP-007-XX| 22| Handle Arm| XX-022-AR
8| Clicker Pin| BP-008-XX| 23| Handle Washer| BP-023-AR
9| Anti-Reverse Dog| BP-009| 24| Main Shaft Screw| BP-024
10| Anti-Reverse Dog Bushing| BP-010| 25| Handle Nut (right hand)| BP-025-RH- AR
11| Anti-Reverse Dog Screw| PCP-011| | Handle Nut (left hand)| BP-025-LH-AR
12| Anti-Reverse Spring| BP-012| 26| Handle Nut Screw| PCP-026-AR
13| Anti-Reverse Spring Screw| PCP-013| 27| Anti-Reverse Dog Stop Screw*| PCP-013 Assembly
14| Spool| XX-014| Not Shown:| Service Tool| BP-29
15| Drag Spring| XX-015| | |

*These are multiple-part components.

255 North Congress Avenue
Delray Beach, FL 33445
Phone: 561-272-0770
Fax: 561-272-0047
Website: tiborreel.com

References

• Tibor Reel Corporation | The World's Finest Fly Reels

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>