roviis Wireless Bluetooth Earbuds User Manual
- June 9, 2024
- roviis
Table of Contents
roviis Wireless Bluetooth Earbuds
PRODUCT OVERVIEW
RESTORE FACTORY SETTINGS (RESETTING AND PAIRING)
- Please place both TWS into the charging case and close the lid (about 3 seconds).
- Please open the lid of the charging case, and long-press the reset button inside the case(more than 8 seconds), please note that you need to release your hand as soon as all 4 white lights above the reset button are on.
- Then you will see the light blinking in the right/left touch area(It flashes quickly for about two seconds and then flashes slowly), which means R2 has been reset and ready for pairing.
- Please continue to keep the lid open, then go to Bluetooth settings and select “ROVIIS R2” on your Bluetooth audio device.
— Once successful, there are two prompts: “pairing successful” and “connected”.
— Once reconnected, there is a prompt “connected”.
- The Earbuds LED lights will flash when the MIC is enabled during a call.
WEARING
Steps:
To achieve the most comfortable fit and sound for your TWS, take time to test out the various tip sizes to find the best fitting size. It is normal to use differently sized tips in each ear.
Step 1: Place the earbuds into your each ear, like picture 1.
Step 2: Whirl the earbuds to be comfortable, like picture 2.
Step 3: Put on the ear hooks and adjust to fit your ears, ensure the Mic 1 align with mouth, like picture 3.
TURN ON
Way 1: Open the charging case
Way 2: Long-press the left or right side of the earbud’s touch area for 3
seconds
TURN OFF
Way 1: Put the earbuds back to the charging case → close the charging
case cover → wait for to charge fully, then the earbuds will turn off
automatically.
Way 2: Earbuds will turn off automatically when the earbuds run out of
power.
Way 3: Earbuds are disconnected with Bluetooth devices more than 5
minutes, the earbuds will turn off automatically
PAIRING
Way 1: Open the charging case → wait for the earbuds to enter pairing
mode automatically (the main ear will flash green light slowly in the touch
area) → pick up the earbuds from the charging case → open your Bluetooth
device → you can see “ROVIIS R2” in the Bluetooth list, pleases click
“pairing”.
Way 2: Open the charging case → put both left and right side earbud into
the charging case → press and hold the reset button for 2~8 seconds and then
release (Once the 2 LED lights are flashing, please release your hand right
now) → enter pairing mode (the main ear will flash green light blinking slowly
in the touch area) → open your Bluetooth device → you can see “ROVIIS R2” in
the Bluetooth list, pleases click “pairing”.
Pairing operation with another device: Open the charging case → put both left
and right side earbud into the charging case → press and hold the reset button
for 2~8 seconds and then release (Once the 2 LED lights are flashing, please
release your hand right now) → enter pairing mode(the main ear
will flash green light blinking slowly in the touch area) In the Bluetooth
settings of your Bluetooth audio device, click to select “ROVIIS R2”. If the
connection is successful, the earbuds’ indicator will go off. (Without the
above operation, the other device will not search for these earbuds)
CHARGING
The earbuds will start charging once they are placed into the charging case and the lid closed. LED lights above the reset button inside the charging case will indicate the charging status:
-
Charging: Solid red light on case.
-
Fully charged: Solid green light on case.
-
To short-press the reset button inside the charging case, LED lights above the reset button will indicate the power of the case.
TOUCH CONTROL (FACTORY DEFAULT)
| Audio Playback| Calls
---|---|---
Play/Pause| Answer/Hang Up
| Voice Assistance|
| | Reject
| Volume +| Volume +
| Volume –| Volume –
| Next Song|
| Previous Song|
RESTORE FACTORY SETTINGS
- Please put both left and right side earbud into the charging case and close the lid (about 3 seconds).
- Please open the lid of the charging case, and long-press the reset button inside the case(more than 8 seconds), please note that you need to release your hand as soon as all 4 white lights above the reset button are on.
- Then you will see the light blinking slowly in the right or left touch area (Two sides flash quickly for about two seconds, and then the right/left side flashes slowly), which means ROVIIS R2 has been reset and is ready for pairing.
SPECIFICATION PARAMETERS
| Earbuds Weight (Single): 9g | Charging Case Weight: 58g |
|---|---|
| Earbuds Weight: 76g | Charging Case Size: 10356.3836.28mm |
| Earbuds Size: 47.8341.2226.59 mm(with ear caps) | Charging Case Battery |
Capacity: 450 mAh
Earbuds Battery Capacity (Single): 40 mAh| Charging Time of The Charging Case
(Wired): 2 Hours
Earbuds Charging Time: 2 Hours| Fast Charging: 15 Minutes = 1 Hour 30 Minutes
Play Time
Play Time Monaural Full Charge: 6 Hours| Full Charge Box: 28 Hours
Speaker Impedance: 16 Ω| Audio Decoding: SBC, AAC
Communication Distance: 10 m (in Open Environment)| Bluetooth Protocol: HFP /
A2DP / AVRCP
Rated Input: 5V 500mA| Operating Temperature: 0 ℃ ~ 45 ℃
Frequency Response Range: 20Hz ~ 20KHz
*The above parameters are obtained from lab test data. Playback time was tested under experimental conditions with AAC format and 50% volume. Playback time and standby time may vary depending on different settings, environment, usage, etc.
WARM TIPS
- When there is no sound on one side of both earbuds, please open the top cover of the charging case, and then long-press the reset button inside the charging case for 2–8 seconds (Once the 2 LED lights are flashing, please release your hand right now), then the main earbuds’ indicator will flash slowly. At this time, please follow the above steps to restore factory settings, then ignore the ROVIIS R2 earbuds from the device Bluetooth list (if any) and re-pair.
- Please clean the pins of the earbuds and charging port with dry tissue regularly to avoid poor contact due to dirt.
- If the other party finds your voice is too low during the call, please try to adjust the wearing position of the earbuds.
- After receiving the product, please put the two earbuds back into the charging case for charging together, which can ensure the effective use of the product.
SUPPORT
If there is any questions or issues, please contact with ROVIIS Support Team, we will respond to you in 24 hours.
Email: support@roviis.com
Brand： ROVIIS
Model： ROVIIS R2
Name： Wireless Earbuds
FCC ID: 2ARYG-SPORTSOUND
Manufacturer： FONBERIC UNITED TECHNOLOGIES Co.,Ltd MADE IN CHINA
FCC WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
Notes: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If thisequipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Note: If shielded cables or special accessories are required for
compliance, a statement must be included which instructs the user to employ
them, for example, Shielded cables must be used with this unit to ensure
compliance with the Class B FCC limits.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>