Midea V2AinCU1 Cyclonic Bagless Vacuum Cleaner Instruction Manual

V2AinCU1 Cyclonic Bagless Vacuum Cleaner
Instruction Manual 385629
VACUUM CLEANER
OPERATION
INSTRUCTIONS MANUAL

V2AinCU1 Cyclonic Bagless Vacuum Cleaner

All the content in the manual have been checked carefully. If there are any errors in printing or misunderstanding in the content, please contact Midea customer service center.
Note: Where there is a technical improvement on the product, it will be included in the new edition of the manual. No further notification will be provided. Refer to the actual product for any changes in the appearance and color of the product.

Safety Introduction

1. Do not place the vacuum cleaner close to heat sources, radiation, or burning cigarette, Do not use the appliance to remove the following objects:
   – All liquids such as water and solvents.
   – Lime, cement, ash and other construction dust and garbage.
   – Hot objects, such as cigarette butts.
   – Sharp objects, such as glass shards, etc.
   – Inflammable and explosive articles, such as gaso line or alcohol products.

2. Do not let children play with or operate the vacuum cleaner to prevent accidents.

3. Your vacuum cleaner is an electric appliance: It must be used appropriately.

4. Do not leave the operating vacuum cleaner unattended.

5. The power must be turned off during cleaning, maintenance or when in storage.

6. Do not pull the power plug to turn off the vacuum cleaner. Hold the plastic part of the plug to remove it from the power socket.

7. The power supply voltage must correspond to that of the vacuum cleaner charging voltage.

8. Keep the power cord away from sharp objects to prevent it from being damaged.

9. To prevent fires do not immerse the vacuum cleaner in water, do not expose it to any heating appliances.

10. Do not drag the power cord when moving the charging station.

11. In the case of below situations do not use the vacuum cleaner and send it immediately to the nearest approved maintenance facility if:
    – The vacuum cleaner fell and consequently damaged.
    – The power cord is damaged.

12. Stop operating the vacuum cleaner if the suction inlet is blocked to prevent damages (such as overheating) to the motor or deformations to the vacuum plastic parts occasioned by overheating motor.

13. Do not press the dust cup button during handling to prevent the machine from falling off.

Product Introduction

1. VainBody
2. tose
3. Extension Tube
4. MainBrush
5. creviceTool
6. Round Brush

Product Operation

Product use

1. Pull out the power cord to connect the power supply:
   When you see the red mark on the power cord, do not pull out the cord outward

2. press the ON/OFF button:
   Control the start and stop of the vacuum cleaner.

3. Press the take up button:
   The power cord is automatically rolled back into the machine,

cavtion
Please slowly take up the cord, to avoid the power cord or power plug bruising human body or furniture in the process of taking up.

Product Maintenance

Dust cup cleaning

1. Remove the dust cup: Press the dust cup release button, gently lift the grip of dust cup and remove the dust cup.
2. Dump the garbage: Tap the dust dumping button to dump the garbage.

How to maintain

1. The filter should be cleaned twice a year, and when there is obvious dirt on the filter, itis time.

2. You must fix the filter properly before running the vacuum cleaner.

3. The filter can’t be cleaned in the washing machine or baked by the blower.

4. It will reduce the suction power and damge the motor if you use the wet filter.

5. Steps for maintenance:

6. Press the outlet lock to open the outlet board, get out the outlet filter.   

7. Rotate the HEPA cover to separate it from the dust cup cover, get the HEPA cover.
   

8. Take the filter out and tap it to remove the dust. If necessary, you can rinse it under water tap.
   

9. Wash the HEPA cover, the HEPA assembly, the outlet sponge and the dust cup in the water without detergent and dry them before use. Don’ t use any tools to brush the HEPA fitler paper, otherwise the HEPA filter will be damaged and filteration effect will be affecteds.

10. Fix the HEPA assembly on the cup cover and make sure three salient cubes should be stuck in the grooves of the dust cup.

11. Rotate the HEPA assembly in the direction of the mark on the cup cover.

12. Assemble the cup cover assembly and the dust cup according to the mark outside.

13. Put the dust cup assembly into the machine. And in this process, first you should make the cup in the right position and then press the handle of the dust cup, if there is a cluck it means the operation is successful.

caition

1. The filter parts can be put back for use only after being cleaned and dried. It is recommended to have sun exposure for 24 hours to ensure it is thoroughly dried
2. All parts must be ensured to be properly installed, otherwise it will cause product failure.
3. Water s not allowed to penetrate into the vacuum cleaner electrical components, or otherwise may cause product failure.

TROUBLESHOOTING

In case of malfunction, please refer to the following table

the socket
-No electricity on the power socket
– The vacuum cleaner switch s not tumed on
– Motor thermal protector acts| – Reinsert the plug
– Check the circuit breaker
-Press the machine’s power switch
– Unplug the plug and wait for the thermal protector torecover
Suction becomes weaker| The main brush or accessories are clogged  weaker
– Dustin the dust barrel is too full
-Dustinthe dust cup flter cotton s toomuch| – Clean up the stemming
-Timely clean up garbage
– Clean the iter cotton

Ifthe problem still can’t be solved, please contact local service center.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>