genexis XGS2120 FiberTwist Series Devices Installation Guide
- June 12, 2024
- genexis
Table of Contents
People deserve fiber.
XGS2120
FiberTwist-Series
Installation Guide
Overview
Button overview
Port overview
ON/OFF button
Power ON or OFF – press and release to switch device ON or OFF
LED overview
Installation guide
Box contents
- Genexis FiberTwist (active device)
- Power adapter
- 2x Spare device label (self-adhesive)
Label position
The product label is positioned on the back of the active device.
Preparation
Ensure there is a power socket within reach of where the device is being
installed.
Important : Instructions need to be followed precisely and uninterrupted.
This minimizes the risk of damage to the fiber optic connectors, causing a
severe degradation of signal quality.
Remove Blind Cover (if present)
- Press and hold the unlock button (see button overview).
- Rotate the Blind Cover counterclockwise till it blocks.
- Remove the Blind Cover from the baseplate (FTU) by pulling it towards yourself.
- Store the Blind Cover in a safe place.
Remove dust cap
- Take the FiberTwist out of the box.
- The dust cap is connected to the red string located on the rear of the FiberTwist.
- Remove the dust cap by pulling the red string.
- Store the dust cap in a safe place.
Twist!
- Place the FiberTwist on the FTU as shown in the picture below, in a 30–degree angle.
- Rotate clockwise until it clicks into place.
- Make sure the FiberTwist is aligned squarely on the FTU, each edge must line up directly with the FTU below.
Your FiberTwist is now installed!
Connecting the FiberTwist
- If required, connect your television / set-top box to the TV port with a coax cable.
- If required, connect your personal device to the LAN port via an RJ45 network cable.
- Connect the supplied power adapter to the FiberTwist and plug the adapter into a power socket.
- Press the ON/OFF button to power on the device.
If at some point in the future it becomes necessary to uninstall the
FiberTwist, please place the Blind Cover back on the FTU immediately and put
the dust cap back on the FiberTwist.
Warning: This product contains a laser that emits invisible light. It is
a Class 1 Laser product, which means it is safe under all conditions of normal
use. However, it is still advised to not look directly into the fiber
connector when the product is powered on.
Warning: Do not cover the device, this will interfere with the
ventilation. Ambient Operating Temperature: 0°C ~ 40°C
EU Declaration of Conformity
Hereby, Genexis Netherlands B.V. declares that the product FiberTwist-XGS2120
is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated
Directive 2015/863 and Ecodesign Directive 2009/125/EC.
The full text of the EU declaration of conformity is available at the
following internet address: https://genexis.eu/product/fibertwist/red
/fibertwist-xgs2120
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
**Signature of authorized person
Place of issue
Eindhoven
The Netherlands
Date of issue
2023-05-02
**
Revision 1.2 – May 2023 – Copyright © 2023 Genexis Netherlands B.V. All rights
reserved.
Multiple languages of this document and additional product information are
available on https://genexis.eu/product/fibertwist/downloads
Genexis assumes no responsibility for any inaccuracies in this document.
Genexis reserves the right to change, modify, transfer, or otherwise revise
this publication without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>