genexis P6416 FiberTwist Series Installation Guide
- June 12, 2024
- genexis
Table of Contents
P6416
Fiber Twist Series
Installation Guide
Wi-Fi Easy Mesh™ supported
Installation with use of app
You’re just a few steps away to install your device via the Genexis Easy WiFi app
1. Scan QR-code
https://genexis.eu/content/uploads/app-redirect/index.html
2. Download app and follow the steps
Installation guide
Fiber Twist P6416 is installed on an FTU/Bracket
Various translations of this document (if available) and additional product
information can be found on https://genexis.eu/product/fibertwist/downloads
Box contents Check if the following items are in the giftbox:
- Genexis Fiber Twist P6416
- Power adapter
- Labels (self-adhesive)
Label position
The product label is positioned on the bottom of the active device. The
relevant device information is also listed on the additional labels included
in the giftbox.
Preparation
Ensure there is a power socket within reach of where the device is being
installed.
Important: Instructions need to be followed precisely and uninterrupted.
This minimizes the risk of damage (a severe degradation of signal quality) to
the fiber optic connectors.
Warning: Do not cover the device with anything, this will interfere with
the ventilation of the Fiber Twist. Operation temperature 0°C ~ 40°C
Remove Blind Cover or active device (if present)
- Press and hold the unlock button (on the right side of the Blind Cover or active device).
- Rotate the Blind Cover or active device counterclockwise till it blocks.
- Remove the Blind Cover or active device from the baseplate (FTU) by pulling it towards yourself.
- Store the Blind Cover or active device in a safe place.
Remove dust cap
- Take the Fiber Twist P6416 out of the box.
- The dust cap is connected to the red string located on the rear of the Fiber Twist P6416.
- Remove the dust cap by pulling the red string.
- Store the dust cap in a safe place.
Twist!
- Place the Fiber Twist P6416 on the FTU/Bracket as shown in the picture below.
- Rotate clockwise until it clicks into place.
- Make sure the Fiber Twist P6416 is aligned squarely on the FTU/Bracket.
Your Fiber Twist P6416 is now installed!
Setting up the Fiber Twist P6416
- If required, connect your telephone to a green telephone port via an RJ11 phone cable.
- If required, connect your personal devices to the yellow LAN ports via an RJ45 network cable.
- Connect the supplied power adapter to the Fiber Twist P6416 and plug the adapter into a power socket.
- Toggle the ON/OFF button on the bottom of the Fiber Twist P6416 in the ON position to turn on the device.
- If the device is connected properly and the service is active on the fiber port, the Status, Uplink and Internet LEDs will have a solid green color.
Switching the WiFi ON/OFF
The WiFi function of the Fiber Twist P6416 can be switched ON or OFF by
means of the Mode button.
-
Switch OFF: On the Fiber Twist P6416, press
and hold the Mode button until the WiFi LED turns off. -
Switch ON: On the Fiber Twist P6416, press and hold the Mode button until the WiFi LED turns on.
Connecting to the wireless network
You can connect your personal device to the Fiber Twist P6416 via manual
pairing. If Automated pairing (WPS) is prefered, please check for your
specific device how this can be initiated. Before pairing , make sure the WiFi
LED is on (solid green). If not, switch the WiFi ON as described in this
installation guide.
Manual pairing
The WiFi network name and WiFi key are printed on the labels of the Fiber
Twist P6416.
- Perform a search of available wireless networks on your personal device or scan the QR-code on the label of the Fiber Twist P6416.
- Select the WiFi network name printed on the labels of the Fiber Twist P6416.
- Enter the WiFi key printed on the labels of the Fiber Twist P6416.
Using the web interface
You can access the Fiber Twist P6416 web interface via a wired connection or
wireless connection.
- Wired connection: Connect an RJ45 network cable between your personal device and the Fiber Twist P6416 LAN port (yellow connector).
- Wireless connection: Connect your personal device to the wireless network as described in this installation guide.
Power saving options Power saving options are available via the web interface.
The Fiber Twist P6416 is a Class 1 laser product.
- Use a web browser on your personal device and navigate to the GUI URL as printed on the labels of the Fiber Twist P6416.
- Login using the credentials as printed on the labels of the Fiber Twist P6416.
Power saving options
Power saving options are available via the web interface.
The Fiber Twist P6416 is a Class 1 laser product.
LED overview
Button overview
Port overview
Reset button (recessed)
Reboot – short press once
Factory reset – long press and hold until the all LED’s start fast blinking
green
ON/OFF switch
Switch ON – flip the switch to ON
Switch OFF – flip the switch to OFF
Troubleshooting
Is the Status LED solid red?
Contact your service provider.
Has the Status LED not been solid blue after WPS pairing?
WPS pairing between the Fiber Twist P6416 and personal device failed. Please
follow the instructions again to connect your personal devices to the Fiber
Twist P6416 via the wireless network.
Is the Status LED blinking yellow and the Uplink LED is blinking green?
The FiberTwist P6416 is being upgraded with new software. Please wait until
the Status LED turns solid green again.
Is the Uplink LED off?
If the Uplink indicator LED is off, despite proper connection, contact your
service provider.
Is the Uplink LED blinking red?
Contact your service provider.
Is the Internet LED blinking green for 5 minutes?
Fiber Twist P6416 does not have a connection with the broadband network.
Please contact your service provider.
Is the WiFi LED off?
Please turn the WiFi ON as described in this installation guide.
Return the Fiber Twist P6416 to factory default settings
With the reset button you can reset the Fiber Twist P6416 to its factory
default settings. You can press this button with a small pin or paperclip.
- Press and hold the reset button until all LED’s start fast blinking green.
- Wait until the Status LED turns solid green again.
Your Fiber Twist P6416 is returned to its default settings as printed on the labels of the Fiber Twist P6416.
EU Declaration of Conformity
Hereby, Genexis Netherlands B.V. declares that the radio equipment type
FiberTwist P6416 is in compliance with Directive 2014/53/EU, Directive
2009/125/EC, Directive 2011/65/EU and Delegated Directive 2015/863.
The full text of the EU declaration of conformity is available at the
following internet addresses:
https://genexis.eu/product/fibertwist/red/fibertwist-p6416
Company Name: Genexis Netherlands B.V.
Company Address: Lodewijkstraat 1a, 5652 AC Eindhoven, The Netherlands
Name and title of authorized person: Maarten Egmond, CTO
Signature of authorized person
Place of issue: Eindhoven The Netherlands
Date of issue: 2022-07-22
Frequency bands and maximum radio frequency power transmitted
The FiberTwist P6416 operates in the frequency bands of 2.4 GHz and 5GHz.
The maximum radio frequency power transmitted in these bands is:
- 20 dBm (100 mW) (EIRP) for the 2400 MHz 2483.5 MHz band
- 23 dBm (200 mW) (EIRP) for the 5150 MHz 5350 MHz band *
- 30 dBm (1000 mW) (EIRP) for the 5470 MHz 5725 MHz band
- In EU, 5150 5350 MHz is restricted to indoor.
Revision 1.1 – November 2022 – Copyright © 2022 Genexis Netherlands B.V.
All rights reserved.
Genexis assumes no responsibility for any inaccuracies in this document.
Genexis reserves the right to change, modify, transfer, or otherwise revise
this publication without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>