Antradar 9001402CA GWK 40V 55lbs Trolling Motor Instruction Manual

Antradar 9001402CA GWK 40V 55lbs Trolling Motor

DESCRIPTION

OVERVIEW

1. Shaft depth adjustment collar
2. Steering tension knob
3. Prop shaft tilt release lever
4. Clamping knobs
5. Boat mounting bracket
6. Tilt/Twist tiller handle
7. Adjustable shaft
8. Propeller
9. Motor

OPERATION

ADJUST THE DEPTH

1. Hold the shaft tightly.
2. Loosen the steering tension knob (2) and depth collar knob (1) until the shaft moves freely.
3. Move the motor to the desired depth.
4. Tighten the depth collar knob (1) to attach the motor in place.

IMPORTANT When you set the depth, make sure the top of the motor is submerged at least 12″ (30 cm) to avoid churning or agitation of surface water. The propeller must be fully submerged.

ADJUST THE BRACKET
You can lock your motor in a vertical position, angle it for shallow water or tilt it completely out of the water.

1. Grasp the shaft tightly.
2. Depress and hold the tilt lever (3).
3. Tilt the bracket (5) to the desired position.
4. Release the tilt lever (3).

MOUNT THE MOTOR

1. Install the bracket (5) on the transom of the boat.
2. Tighten the clamp knobs ( 4) tightly.

TIL THE TWIST TILLER HANDLE
The twist tiller handle has five available positions.

NOTE: The twist tiller handle is shipped in the down position. Pull the handle tightly up to the horizontal position.

1. Pull the twist tiller handle (6) up to 15°, 30° or 45° position.
2. Pull the twist tiller handle (6) down to 45° position.

ADJUST THE SPEED
The machine offers a choice of five forward and three reverse speeds .

1. Turn the twist tiller handle ( 6) counterclockwise from 0 (OFF) position to increase the reverse speed.
2. Tum the twist tiller handle (6) clockwise from O (OFF) position to increase the forward speed.

INSTALL THE BATTERY PACK
WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the engine stops before you install or remove the battery pack.
• Read, know, and do the instructions in the battery and charger manual.

1. Press the door release button (12).
2. Open the battery door.
3. Align the lift ribs on the battery pack (11) with the grooves in the battery compartment.
4. Push the battery pack ( 11) into the battery compartment until the battery pack locks into place.
5. When you hear a click, the battery pack is installed.
6. Close the battery door.

REMOVE THE BATTERY PACK

1. Open the battery door (14).
2. Push and hold the battery release button (13).
3. Remove the battery pack (11) from the machine.

MAINTENANCE

CAUTION
Do not let brake fluids, gasoline, or petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.

WARNING
Remove the battery pack from the machine before maintenance.

REPLACE THE PROPELLER

1. Hold the propeller (8) tightly.

2. Loosen the prop nut (15) with a wrench.

3. Remove the prop nut (15) and washer (16).

4. Replace with a new propeller.
   WARNING Make sure you align the slot (17) of the propeller with the dirve pin (18).

5. Reinstall the prop nut and washer.

CAUTION Tighten the prop nut 1/4 turn past snug (25 – 35 in lbs.). Don’t overtighten the prop nut, it may cause damage to the prop or cause too much pressure/strain on the motor which may cause overheating or premature battery drain.

STORE THE MACIDNE

• Make sure the battery is removed.
• Clean housing and the plastic components with a moist and soft cloth.
• Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/ instructions:
  • replace the damaged parts.
  • tighten the bolts or nuts.
  • speak to an authorized service center.
• Keep the propeller free of weeds and fishing line.
• Keep the leading edge of the blades smooth. If there are nicks or rough edges, it is suggested to correct by using a smooth file or fine sandpaper.

TROUBLESHOOTING

TECHNICAL DATA

LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. Greenworks, at its own discretion, will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been purchased or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners’ manual supplied with the product when new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, ifit has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.

HELPLINE: Warranty service is available by calling our toll-free helpline at 1-888-909-6757.
TRANSPORTATION CHARGES: Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.

EXPLODED VIEW

USA address:
Greenworks Tools
P.O. Box 1238
Mooresville, NC 28115

Canadian address:
Greenworks Tools Canada, Inc.
P.O. Box 93095, Newmarket, Ontario
L3Y 8K3

www.greenworkstools.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>