KARCHER IB10, 8 L2P Dry Ice Blaster Instruction Manual

: June 12, 2024
: Karcher

IB 10/8 L2P

IB10, 8 L2P Dry Ice Blaster

General notes

Read the original instructions before using the device for the first time and act in accordance with it.
Keep the original instructions for future reference or for future owners.

Intended use

The device is used to remove dirt with dry ice pellets that are accelerated by an air jet.
The dry ice pellets are produced in the device. This requires liquid carbon dioxide from a dip tube bottle.
The device may not be operated in a potentially explosive atmosphere.
The minimum air exchange specified in the “Technical data” section must be observed at the operating location.
The casing of the device may only be removed by KÄRCHER Customer Service for maintenance purposes.

CO2 quality
To ensure trouble-free operation, the carbon dioxide used must at least comply with the following specifications:

Carbon dioxide technical, class 2.5 or better
Purity ≥ 99.5%
Water content (H2O) ≤ 250 ppm
NVOC (oil and fat) ≤ 2 ppm

Function

Carbon dioxide snow is created via decompression of liquid carbon dioxide. The gaseous carbon dioxide that also arises is carried away from the workplace via the exhaust hose.
The carbon dioxide snow is pressed into dry ice pellets in the device. Compressed air reaches the jet gun via a solenoid valve.
The air pressure is controlled by an on-site pressure reducer. When the trigger of the jet gun is activated, the valve opens and the air jet emerges from the jet gun. Dry ice pellets are additionally dosed into the air jet via a dosing device.
The dry ice pellets hit the surface to be cleaned and remove the dirt. The -79 °C cold dry ice pellets also create thermal stresses between the dirt and the object to be cleaned, which also contribute to the loosening of the dirt. In addition, the dry ice immediately turns into gaseous carbon dioxide when it hits the surface, thus taking up 700 times its volume. Dirt penetrated by the dry ice is blown away as a result.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials and often components such as batter- ies, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.
Notes on the content materials (REACH) Current information on content materials can be found at: www.kaercher.com/ REACH

Safety instructions

The device may only be operated by persons who have read and understood these operating instructions. In particular, all safety instructions must be observed.
Store these operating instructions so that they are available to the operator at all times.
The operator of the unit must carry out a risk assessment on site and ensure that operators are instructed.

Hazard levels
DANGER

Indication of an imminent threat of danger that will lead to severe injuries or even death.

WARNING

Indication of a potentially dangerous situation that may lead to severe injuries or even death.

CAUTION

Indication of a potentially dangerous situation that may lead to minor injuries.

ATTENTION

Indication of a potentially dangerous situation that may lead to damage to property.

Symbols on the unit
Danger from flying dry ice pellets.
Do not point the jet gun at people. Remove third parties from the operating location and keep them away (e.g. via barriers) during operation. Do not touch the nozzle or the dry ice jet during operation.
CO2 Risk of suffocation from carbon dioxide.
During operation, the carbon dioxide content of the air at the workplace increases.

Make sure there is sufficient air exchange at the workplace. Lay the exhaust hose outdoors, for example, so that nobody is endangered by carbon dioxide. Note: Carbon dioxide is heavier than air.
Make sure that carbon dioxide does sink to lower-lying areas, for example by flowing from the outside into a basement below the workshop (flows). For longer jet work (longer than 10 minutes per day) and especially in small rooms (less than 300 m³), we recommend wearing a carbon dioxide warning device. Signs of high levels of carbon dioxide: 3…5%:
Headache, high breathing rate. 7…10%: Headache, nausea, possibly unconsciousness. If these symptoms occur, switch off the device immediately and get some fresh air. Before continuing work, improve ventilation or use a breathing apparatus.
Carbon dioxide is heavier than air and col- lects in confined spaces, lower- lying spaces or in closed containers. Ensure adequate ventilation at the workplace. Observe the safety data sheet from the carbon dioxide supplier.
Risk of injury, risk of damage from electrostatic charging. The cleaning object can become electrostatically charged during the cleaning process. Ground the object to be cleaned and keep it grounded it until the cleaning process is complete.
Risk of injury from electric shock.
Do not open the device. Work on the device may only be performed by KÄRCHER Customer Service. Risk of injury from cold burns. Dry ice has a temperature of 79 °C. Do not touch the dry ice or cold parts of the unit. Risk of injury from carbon dioxide bottle falling over, Danger of suffocation due to carbon dioxide Attach the carbon dioxide bottle securely.

| Risk of injury from cold burns.
Dry ice has a temperature of 79 °C. Do not touch the dry ice or cold parts of the unit.
---|---
| Risk of injury from carbon dioxide bottle falling over, Danger of suffocation due to carbon dioxide Attach the carbon dioxide bottle securely.
| Risk of injury from flying dry ice pellets and dirt particles.
Wear safety goggles.
Danger of hearing damage.
Wear hearing protection.
| Risk of injury from flying dry ice pellets and dirt particles.
Wear protective gloves according to EN 511.
| Risk of injury from flying dry ice pellets and dirt particles.
Wear long-sleeved protective clothing.
| Caution! Permanent malfunctions possible.
Traces of fat or oil interfere with the formation of dry ice snow in the device.
Do not use grease, oil or other lubricants on the connection nozzle or on the thread of the carbon dioxide bottle or the carbon dioxide hose.

General safety instructions
DANGER Risk of injury The device may start up unexpectedly. Unplug the mains plug from the power socket before working on the device. Risk of injury Dry ice and cold device parts can cause cold burns on contact with the skin. Wear cold protection clothing or allow the device to warm up before working on the device. Never put dry ice in your mouth. Risk of injury The dry ice jet can be dangerous if used improperly. Do not direct the dry ice jet at persons, live electrical equipment or at the device itself. Do not aim the dry ice jet at yourself or oth- ers, e.g. to clean clothes or shoes. Risk of injury Light objects can be blasted away by the dry ice jet. Fix light objects in place before starting cleaning.

Risk of asphyxiation
Increased concentration of carbon dioxide in the air you breathe can lead to death from suffocation. Make sure that no exhaust gases are emitted close to air vents.
Provide adequate ventilation in the workplace and ensure that the exhaust gases are properly discharged.

WARNING
Risk of injury
The recoil force of the jet gun can throw you off balance. Find a safe place to stand and hold the jet gun firmly before you pull the trigger.
Risk of injury Dry ice pellets and dirt particles can hit and injure people. Do not use the device when other people are within range unless they are wearing protective clothing. Do not use the device if a power cable or important parts of the device are damaged, e.g. safety devices, abrasive hose, jet gun.

Safety instructions for gas bottles

DANGER Risk of bursting, risk of suffocation Gas bottles can burst if they become too hot or if they are mechanically damaged. Leaking carbon dioxide can cause death by suffocation. Protect gas bottles from excessive heat, fire, dangerous corrosion, mechanical damage and unauthorized access. Store gas bottles so that no escape routes are restricted.
Do not store gas bottles in underground rooms, on and at stairs, in hallways, corridors and garages.
Do not store gas bottles together with flammable materials. Store gas bottles upright. Secure gas bottles against tipping over or falling.
Close the bottle valve before transporting gas bottles. Transport gas bottles with a gas bottle cart or a vehicle and secure the bottles against falling.
Pull on the protective cover before lifting the gas bottle to check that the protective cover is securely in place. Secure the gas bottle at the point of use against falling over. Do not open the bottle valve to check the pressure.
Open and close the bottle valve only by hand without the aid of tools. Check the bottle valve/device connection for leaks.
Close the bottle valve during work breaks and at the end of work to prevent uncontrolled gas escaping. Only empty gas bottles so far that a small residual pressure remains in the bottle in order to prevent foreign matter from entering. When the gas bottle has been emptied to the residual pressure, first close the bottle

valve before unscrewing the extraction device. The gas bottle still has considerable residual pressure. Before returning it, screw the locking nut and the protective cover onto the gas bottle.
If the gas escapes uncontrolled, close the bottle valve. If the gas emission cannot be stopped, take the bottle outside or leave the room, lock the access and only enter and ventilate the room if a concentration measurement rules out a danger.

Regulations and guidelines In the Federal Republic of Germany, the following regulations and guidelines apply to the operation of this system (available from Carl Heymanns Verlag KG, Luxemburger Straße 449, 50939 Cologne):

DGUV R 100-500 Working with blasting machines
DGUV 113-004 Working in confined spaces
DGUV 113-004 Use of protective clothing
DGUV 113-004 Use of protective gloves
DGUV 113-004 Working with jet units
DGUV 213-056 Gas warning unit
VDMA 24389 Systems for dry ice jet – safety requirements

Switching off in the event of an emergency

Release the trigger of the jet gun.
Turn the program switch to “0/OFF”.
Close the stop valve on the carbon dioxide bottle.
Shut off the compressed air supply.

Safety devices
CAUTION
Missing or modified safety devices
Safety devices are provided for your own protection.
Never modify or bypass safety devices.
Safety lever
The safety lever prevents unintentional activation of the jet gun.
The trigger can only be operated when the safety lever has been raised beforehand.

Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.
Protective clothing
Full-view safety goggles, anti-fog, part no .: 6.321-208.0
Cold protection gloves with anti-slip profile, category III according to EN 511, part no .: 6.321-210.0
Hearing protection with headband, part no .: 6.321-207.0

Scope of delivery
Check the contents for completeness when unpacking. If any accessories are missingor in the event of any shipping damage, please notify your dealer.

Control elements

Illustration A

Steering roller with parking brake ® Abrasive hose coupling
Control cable coupling
Control panel
Push handle
Holder for jet gun
Storage area
Nozzle holder
Display
Program switch
Fault indication pellet dosing
Lights up red: The drive motor of the dosing device is blocked
Flashes red: The drive motor of the dosing device is overheated
Fault indication pellet generation
Lights up red: The drive motor for pellet production is blocked
Compressed air supply fault indicator
Lights up red: Compressed air supply has too little pressure
Flashes red: The internal pressure is too high
Voltage supply indicator lamp
Lights up green: Voltage supply OK
Compressed air indicator light
Lights up green: Compressed air supply OK.
Jet gun fault indicator
Lights up yellow: The trigger is fastened (e.g. cable tie)
Flashes yellow: no jet gun connected to the device
Jet nozzle
Jet gun
Compressed air / pellets button with indicator light
Lights up red: Compressed air jet
Off: Pellet jet
Trigger
Safety lever
Retaining cone
Abrasive hose
Bottle connection
Screw plug
Copper sealing ring
Carbon dioxide filter () Screw flange
Bottle connection seal (order number 574-316.0)
Carbon dioxide immersion pipe bottle (not included in the scope of delivery)
Carbon dioxide hose
Carbon dioxide bottle retaining belt
Homebase retaining rail
Hose/cable holder with rubber tensioner
Opening for resetting the motor circuit breaker
Handle
Compressed air connection
Storage space for carbon dioxide bottle
Carbon dioxide exhaust hose
Mains connection cable with mains plug
Holder for abrasive hose
Drain tap for condensation water

Initial startup

DANGER
Risk of injury
Dry ice pellets can escape from damaged components and cause injuries.
Before initial startup, check all components of the device, especially the abrasive hose, to ensure that they are in good condition.
Replace damaged assemblies with flawless ones.
Clean soiled assemblies and check that they are working properly.

ATTENTION
Risk of damage Condensation water can drip from the device casing onto the floor. Do not operate the device on surfaces that are sensitive to moisture.

Open the drain tap and drain the condensation water that has collected in the device.
Close the drain tap. 3. Store the device on a level and flat surface.
Block the steering rollers with the parking brakes.
Connect the abrasive hose to the coupling on the device.
1 Control cable
2 Union nut
3 Control cable coupling
4 Abrasive hose coupling
5 Union nut
6 Abrasive hose
Unscrew the union nut of the abrasive hose and slightly tighten it with an openend wrench.
Plug the control cable into the device.
Screw on the union nut of the control cable and tighten by hand.
Insert the jet gun with the retaining cone into the holder on the device.

DANGER
Risk of asphyxiation Carbon dioxide escapes from the exhaust hose. From a concentration of 8 percent by volume in the breath, carbon dioxide leads to unconsciousness, respiratory arrest and death. The maximum workplace concentration is 0.5%. Carbon dioxide is heavier than air and collects in pits, basements and de- pressions. Lay the exhaust hose so that nobody is endangered by the escaping carbon dioxide.
Note: Carbon dioxide is heavier than air. Make sure that carbon dioxide does sink to lower-lying areas, for example by flowing from the outside into a basement below theworkshop (flows).
Lay the exhaust hose outdoors or connect it to an extraction device.

Operation

DANGER
Risk of injury
Dry ice pellets flying around can cause injuries or cold burns.
Do not point the jet gun at people.
Remove third parties from the operating location and keep them away (e.g. via barriers) during operation. Do not touch the nozzle or the dry ice jet during operation.

Carry out all maintenance work from the chapter “Care and maintenance / daily before starting operation”.
Cordon off the work area to prevent people from entering during operation.

DANGER
Risk of asphyxiation
Risk of suffocation from carbon dioxide. The dry ice pellets consist of solid carbon dioxide. The carbon dioxide content of the air at the workplace increases when the device is operated.
Lay the exhaust hose outdoors, for example, so that nobody is endangered by carbon dioxide. Note: Carbon dioxide is heavier than air. Make sure that carbon dioxide does sink to lower-lying areas, for example by flowing from the outside into a basement below the workshop (flows). For longer jet work (longer than 10 minutes per day) and especially in small rooms (less than 300 m³), we recommend wearing a carbon dioxide warning device.
Signs of high carbon dioxide concentration in the air you breathe: 3…5%: Headache, high breathing rate. 7…10%: Headache, nausea, possibly unconsciousness.
Turn off the device immediately and seek fresh air at the first signs of these symptoms. Before continuing work, be sure to improve the ventilation measures or use a breathing apparatus.
Observe the safety data sheet provided by the carbon dioxide supplier.

Danger from substances harmful to health.
Substances removed from the object to be cleaned are whirled up as dust. Adhere to the appropriate safety measures if harmful dusts can arise during the cleaning process. Risk of explosion A mixture of iron oxide and light metal dust can ignite under unfavourable conditions and generate intense heat. Never work on light metals and ferrous parts at the same time.
Clean the work area and the extraction device before you work on the respective other material. 3. When working in confined spaces, ensure that there is sufficient air exchange to keep the carbon dioxide concentration in the room air below the dangerous level.
Fasten light cleaning objects in position.

Cleaning with dry ice pellets

Select operation with pellet jet using the compressed air / pellets button. (The indicator light must not light up.)
Illustration I
1 Compressed air / pellets button with indicator light Lights up red:
Compressed air jet Off: Pellet jet
Set the jet pressure on the on-site pressure reducer to the desired value.
Maximum pressure: 10 bar. Minimum pressure:
• Level 1: 0.7 bar
• Level 2: 1.4 bar
• Level 3: 2.8 bar
Note
The pressure is shown in the display. If the minimum pressure is not reached or the maximum pressure is exceeded, the display flashes.
Point the jet gun away from your body.
Push the safety lever of the jet gun upwards and at the same time activate the trigger.
Illustration K
1 Safety lever
2 Trigger
3 Working light
The working light switches on at the same time as the pellet production.
Wait until the pellet jet has built up.
ATTENTION
Never operate the device without or with an empty carbon dioxide bottle.
Use the program switch to select a higher level or change the carbon dioxide bottle if no pellets come out of the jet gun after 5 minutes of jet.
If necessary, turn the program switch back to level 2 or 1.
ATTENTION
Risk of damage
Coarse pellets may possibly escape.
Check the cleaning performance on a nonvisible area first to avoid damage.
Note
If there are interruptions in the dry ice stream, increase the blasting pressure or set a lower level on the programme selector switch.
Direct the pellet jet at the object to be cleaned and remove the dirt with the jet.
Release the trigger.
The pellet jet stops.
The working light goes out after 30 seconds.
Insert the jet gun with the retaining cone into the holder on the device.
Illustration J
1 Holder
2 Retaining cone
3 Jet gun
Close the stop valve on the carbon dioxide bottle if the work break lasts longer than 30 minutes.

Ending operation

Release the trigger of the jet gun.
Close the stop valve on the carbon dioxide bottle.
Pull the trigger on the jet gun until no more pellets come out.
Turn the program switch to level 1.
Shut off the compressed air supply.
Operate the trigger on the jet gun until the compressed air has escaped from the device.
Turn the program switch to “0/OFF”.
Pull the mains plug out of the socket.
Wind up the power cord, hang it on a hose/cable holder and secure with the rubber tensioner.
Illustration L
1 Mains cable
2 Hose/cable holder
3 Rubber tensioner
4 Exhaust hose
Disconnect the compressed air hose from the device.
Wind up the exhaust hose, hang it on a hose/cable holder and secure it with the rubber tensioner.
Wind up the abrasive hose and hang it on the abrasive hose holder.
Insert the jet gun with the cone into the holder on the device.

Transport

CAUTION
Risk of accidents and injuries
Take the weight of the device into account for transportation and storage. See chapter “Technical data”.
ATTENTION
Risk of damage
Engine oil can escape when transporting horizontally. A subsequent lack of oil can lead to damage during the next operation.
Transport the device only in a standing upright position.

Carry out all the steps in the “Ending operation” chapter before transport.
Release the parking brakes on the steering rollers and push the device by the push handle.
Remove the carbon dioxide bottle from the device before loading it into a vehicle.
The device can be lifted by 2 people.
Each person uses a handle on the underside of the device and supports the device with the other hand on the upper edge.
For transport in vehicles, lock the parking brakes on the steering rollers and secure the device with a tension belt.
Illustration M

Storage

CAUTION
Risk of accidents and injuries
Take the weight of the device into account for transportation and storage. See chapter “Technical data”.
The device may only be stored indoors.
DANGER
Risk of asphyxiation
Carbon dioxide can accumulate in enclosed spaces and cause death by asphyxiation.
Only store carbon dioxide bottles (even if they are connected to the device) in well ventilated locations.

Care and service

Maintenance instructions
Regular maintenance according to the following maintenance plan is fundamental for a safely operating system. Use only original manufacturer spare parts or parts recommended by the original manufacturer, such as

Spare parts and wearing parts,
Accessories,
Operating materials,
Detergent.

DANGER
Danger of accident
The device can start unintentionally. Cold unit parts or liquid carbon dioxide can cause frostbite. Gaseous carbon dioxide can cause death by asphyxiation. Before working on the device, carry out all the steps in the “Ending operation” chapter.Wait until the device has warmed up or wear cold protection clothing. Never put dry ice in your mouth.
ATTENTION
Risk of damage Using the wrong detergent can damage thedevice and the jet gun. Never clean the device or the jet gun with solvents, petrol or detergents containing oil.

Service contract
We recommend that you close a service contract to ensure reliable operation of the system. Please contact your KÄRCHER customer service department responsible.
Maintenance plan
Daily before the start of operations

Carefully examine the abrasive hose for cracks, kink points and other damage. Soft spots in the hose indicate wear on the inside of the hose. Replace the defective or worn hose with a new hose.
Examine electrical cables and plugs for damage. Have defective parts replaced by Customer Service.

Every 100 operating hours

Check the couplings on the abrasive hose and on the device for damage and wear. Replace a defective hose, have defective couplings on the unit replaced by Customer Service.

Every 500 operating hours or annually

Have the device checked by Customer Service.

Every 2 years

Renew the abrasive hose at least every 2 years.

Tests
According to DGUV R 100-500, the following tests must be carried out on the unit by an expert. The results of the test must be recorded in a test certificate. The operator of the device must keep the test certificate until the next test.
After a business interruption of more than a year

Check the device for correct condition and function.

After changing the installation site

Check the device for proper condition, function and installation.

After repair work or changes that can affect operational safety

Check the device for proper condition, function and installation.

Troubleshooting guide

DANGER
Danger of accident
The device can start unintentionally. Cold device parts or liquid carbon dioxide can cause frostbite. Gaseous carbon dioxide can cause death by asphyxiation.
Before working on the device, carry out all the steps in the “Ending operation” chapter.
Wait until the device has warmed up or wear cold protection clothing. Never put dry ice in your mouth.
ATTENTION
Risk of damage
Using the wrong detergent can damage the device and the jet gun.
Never clean the device or the jet gun with solvents, petrol or detergents containing oil.

Fault display
Faults are indicated by the indicator lights on the control panel.
Illustration N

Jet gun fault indicator
Compressed air supply fault indicator
Fault indication pellet generation
Fault indication pellet dosing

Troubleshooting
Malfunctions often have simple causes that you can remedy yourself using the following overview.
When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Kärcher Customer Service.

Fault	Rectification
The Jet gun fault indicator lights up	• Do not pull the trigger of the jet

gun before switching it on.
• Remove the fastener on the trigger of the jet gun.
The Jet gun fault indicator flashes| • Check that the control cable of the jet gun is connected to the device.
• Check the control cable on the abrasive hose for damage.
The compressed air supply fault indicator lights up| • Increase the air pressure.
The compressed air supply fault indicator flashes| • Check the exhaust hose for clogging.
• The carbon dioxide bottle is too hot and therefore has too high a pressure Set up the device including the carbon dioxide bottle in a cooler location or protect it from direct sunlight.
The pellet production fault in dlcator lights up| • Allow the device to thaw out. Check the carbon dioxide filter and change it if necessary. Then perform a reset.
• If the malfunction occurs repeatedly, replace the carbon dioxide bottle.
The pellet metering fault indi- cator lights up| • Switch the device off and back on again.
• If the fault indicator remains lit, contact the customer service.
The pellet metering fault indi- cator flashes| • Allow the metering motor to cool down. Position the device so that air can flow into the device from below. Contact Customer Service if necessary.
The voltage supply Indicator light does not light up| • Plug the mains plug into the socket.
• Check the on-site voltage supply.
The compressed air Indicator light does not light up| • Connect a compressed air hose to the device.
• Open the stop valve in the on-site compressed air supply.
The device does not work| • Check the indicator lights and fault indicators.
• Perform a reset.
Poor cleaning performance| • Turn the program switch to a higher level.
• Increase the jet pressure.
• Check the filling level of the carbon dioxide bottle.
• Do not use a heated carbon dioxide bottle. Protect the carbon dioxide bottle from heat radiation. The effectiveness of the pellet production drops sharply if the temperature of the carbon dioxide is above 31 °C.
• Allow the abrasive hose and the jet gun to thaw to clear any blockages. Then increase the jet pressure.
Pellet dosage too low| • Turn the program switch to a higher level.
• Replace the carbon dioxide filter between the carbon dioxide bottle and the device.
Recurring interruptions in the dry ice stream| • Turn the programme switch to a lower level or increase the jet pressure.
• If the jet nozzle is clogged:
a Immediately close the carbon dioxide bottle.
b Allow the unit to thaw for 30 minutes.
c Increase the jet pressure.
d Start the appliance with the carbon dioxide bottle closed to remove pellet residues.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address)

Accessories

ABS residual pressure valve
Order number 2.574-006.0
Necessary when using carbon dioxide bottles with a residual pressure valve.

Technical data

Electrical connection

Mains voltage| V| 220…
| | 230
Phase| –| 1
Frequency| Hz| 50…6
| | 0
Power rating| kW| 1,0
Degree of protection| | IPX4
Leakage current, typical| mA| <3,5
Residual current device| delta I, A| 0,03
Compressed air connection
Compressed air hose, nominal width (min.)| Inches| 0,5
Pressure (max.)| MPa| 1,0
| (bar)| (10)
Compressed air consump-| m3/| 0,8
tion, max.| min|
Device performance data
Jet pressure, max.| MPa| 1,0
| (bar)| (10)
Jet pressure, min. level 1| MPa| 0,07
| (bar)| (0,7)
Jet pressure, min. level 2| MPa| 0,14
| (bar)| (1,4)
Jet pressure, min. level 3| MPa| 0,28
| (bar)| (2,8)
Carbon dioxide consumption| kg/h| 20…60

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.
Product: Ice Blaster
Type:
1.574-xxx (IB 10/8 L2P)
Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2014/30/EU
2011/65/EU
2009/125/EC + 2009/1781
Harmonised standards used
EN 60335-1
EN IEC 63000: 2018
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2021/02/01

Declaration of Conformity (UK)
We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval. Product: Ice Blaster

Type:
1.574-xxx (IB 10/8 L2P)
Currently applicable UK Regulations
S.I. 2008/1597 (as amended)
S.I. 2016/1091 (as amended)
S.I. 2012/3032 (as amended)
2009/125/EC + 2009/1781
Designated standards used
EN 60335-1
EN IEC 63000: 2018
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2021/02/01

THANK YOU!
GRACIAS!MERCI! DANKE!
Register your product and benet from many advantages.
www.kaercher.com/welcome
Rate your product and tell us your opinion.

KARCHER EDI 4 Electric Ice Scraper - sembly3 | www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212| http://kaer.ch/er/?l=TwSoJtl9IUOwZyAe1rHDyw
---|---|---