Smart Power TBF15C-1120 Copier Guardian II Electronic Power Conditioner User Manual
- June 12, 2024
- Smart Power
Table of Contents
Smart Power TBF15C-1120 Copier Guardian II Electronic Power Conditioner
Product Information
Copier Guardian II with Smart Ground Electronic Power Conditioner
The Copier Guardian II with Smart Ground Electronic Power Conditioner is a high-performance power protection and filtrationdevice designed for electronic equipment. It provides the necessary protection for your connected equipment.
Model / Part Numbers:
- TBF15C-1120
- TBF15C-1111TN
- TBF15C-1121TN
- TBF15C-1131TN
- TBF20C-1210
- TBF20C-1211TN
- TBF20C-1221TN
- TBF15CZ-1121TN
- TBF20CZ-1211TN
- TBF15C-2111TN
- TBF20C-2211TN
Features:
- Modem & Data Protection (model dependent): Provides protection for phone and network lines with RJ11 and RJ45 jacks, making it ideal for Fax/Internet/Network users.
- Power Surge Protection: Guards against power surges that can pass through phone lines and network cables to protect copiers.
- Internal Protection: The device features internal protection that disconnects the surge protective component at the end of its useful life, but maintains power to the load, which may require device replacement as per manufacturer’s instructions.
Warnings and Cautions:
- Installing this device without at least 10 meters (30 feet) of wire between the electrical outlet and the electrical service panel will void the warranty.
- Do not plug the device into another relocatable power tap to avoid the risk of electric shock.
For any questions or technical support, contact our Tech Support line at 1-800-772-7633 or email us at [email protected].
Product Usage Instructions
Installation and Protection for Telephone Line and Network Cable
Installation of Copier Guardian II:
- Turn off and unplug the equipment to be protected from the wall outlet.
- Plug the equipment into the Copier Guardian II unit.
- Plug the Copier Guardian II unit into a grounded wall outlet.
- Ensure that the monitoring lights on the Copier Guardian II unit can be observed.
Protection for Telephone Line:
- Unplug the equipment’s telephone cable from the wall jack.
- Plug the equipment’s telephone cable into the RJ11 DEVICE jack on the Copier Guardian II unit.
- Plug the provided telephone cable into the RJ11 LINE jack on the Copier Guardian II unit.
- Plug the other end of the telephone cable into the RJ11 wall jack.
Protection for Network Cable:
- Unplug the equipment’s network cable from the wall RJ45 network jack.
- Plug the equipment’s network cable into the RJ45 DEVICE jack on the Copier Guardian II unit.
- Plug the provided network cable into the RJ45 LINE jack on the Copier Guardian II unit.
- Plug the other end of the network cable into the wall RJ45 network jack.
Important Notes:
- Never install telephone wiring during a lightning storm.
- Disconnect the telephone line at the network interface before installing the secondary protector.
- The device is intended for indoor use only.
- Telephone Line Protection clamping voltage is 250-350 VDC.
Thank you for purchasing this Copier Guardian II.
Smart Power Systems is dedicated to developing and manufacturing the highest-
performance power protection and filtration devices for your electronic
equipment. Proper use of this device will provide the protection needed for
your connected equipment.
Use this user’s guide for the following products:
| MODEL / PART NUMBER | DESCRIPTION |
|---|---|
| TBF15C-1120 | 120V/15A, two 5-15R outlets |
| TBF15C-1111TN | 120V/15A, ONE 5-15R pigtail outlet, RJ11+RJ45 |
| TBF15C-1121TN | 120V/15A, two 5-15R outlets , RJ11+RJ45 |
| TBF15C-1131TN | 120V/15A, two 5-15R outlets and one 5-15R pigtail outlet, |
RJ11+RJ45
TBF20C-1210| 120V/20A, one 5-20R pigtail outlet
TBF20C-1211TN| 120V/20A, one 5-20R pigtail outlet, RJ11+RJ45
TBF20C-1221TN| 120V/20A, one 5-15R outlet, one 5-20R pigtail outlet, RJ11+RJ45
TBF15CZ-1121TN| ZERO CROSS PROTECTION, 120V/15A, two 5-15R outlets, RJ11+RJ45
TBF20CZ-1211TN| ZERO CROSS PROTECTION, 120V/20A, one 5-20R outlet, RJ11+RJ45
TBF15C-2111TN| 208V – 240V/15A, one 6-15R pigtail outlet, RJ11+RJ45
TBF20C-2211TN| 208V – 240V/20A, one 6-20R pigtail outlet, RJ11+RJ45
CAUTION
- Use only in dry locations indoors.
- Avoid dropping the unit.
- Only plug the Copier Guardian II into a three pronged grounded outlet. This unit is not to be used with any type of ground “lift” or pin eliminator.
- Do not open the Copier Guardian II unit, there are no serviceable parts inside. Opening the unit will void your warranty.
This device features an internal protection that will disconnect the surge protective component at the end of its useful life but will maintain power to the load now unprotected. If this situation is undesirable for the application, follow the manufacturer’s instructions for replacing the device.
Do not install this device if there is not at least 10 meters (30 feet) or more of wire between the electrical outlet and the electrical service panel.
Risk of Electric Shock. Do not plug into another relocatable power tap.
FEATURED
Modem & Data Protection (model dependent)
Protection is extended to your phone and network lines with the addition of
RJ11 and RJ45 jacks on the Copier Guardian II unit, creating ideal protection
for Fax/Internet/Network users. Power surges can pass to a copier through
phones lines and network cables.
INSTALLATION OF TBF™
- Turn off and un-plug equipment to be protected from wall outlet.
- Plug the equipment into the Copier Guardian II Unit.
- Plug the Copier Guardian II unit into grounded wall outlet.
- Your equipment is now fully protected. Place the Copier Guardian II where monitoring lights can be observed.
Installation for Protection for Telephone Line and Network Cable TELEPHONE
- Unplug the equipment’s telephone cable from the wall jack and plug into the RJ11 “DEVICE” on the Copier Guardian II.
- Plug the provided telephone cable to the RJ11 jack “LINE” on the Copier Guardian II.
- Plug the other end of the telephone cable into the RJ11 wall jack.
CAUTION:
- Never install telephone wiring during a lightning storm.
- Disconnect telephone line at the network interface before installing the secondary protector.
- Intended for indoor use only.
Telephone Line Protection clamping voltage 250-350 vdc.
NETWORK
- Unplug the equipment’s network cable from the wall RJ45 network jack and plug into the RJ45 “DEVICE” on the Copier Guardian II.
- Plug the provided network cable to the RJ45 jack “LINE” on the Copier Guardian II.
- Plug the other end of the network cable into the wall RJ45 network jack. Your equipment is now fully protected. Place the Copier Guardian II where monitoring lights can be observed.
The GREEN light confirms properly the connected equipment is fully protected. The RED light indicates over voltage, improper ground connection or reversed power wires which needs to be corrected. In an over voltage incident, power is disconnected to protect the connected equipment. IMPORTANT: If the RED Light comes on, contact your electrician to inspect and correct the outlet wiring in order to receive the maximum protection for your connected equipment.
NOTE: All Copier Guardian II units come with security straps, warning label and Velcro™ to secure unit to connected equipment.
IMPORTANT: Velcro™ strips are provided so Copier Guardian II can be attached to copier when needed. Do not place Velcro™ over label.
TRANSFORMER BASED FILTER (TBF™) SERIES
Considered to be one of the most significant developments in the power
protection industry. TBF™ Filters contain innovative technology that combines
Surge Suppression and Noise Isolation which filters the noise on the ground to
less than 0.5 Volts (US Patent # 6229682). Exclusive “POVP” Prolonged Over
Voltage Protector (US Patent # 6560086) disconnects the output power if
voltage exceeds 155 volts. Exclusive Smart Technology (US Patent #5721661)
protects microprocessor based equipment against reverse polarity or no ground.
The patented TBF™ filters prevent 90% of the power problems experienced by
your POS system, computer, copier and facsimile machine.
OTHER POWER PROTECTION PRODUCTS
MEGA CONDITIONERS
The most advanced electronic power conditioner on the market for half the
price and a quarter of the weight of an isolation transformer. The Mega
Conditioner offers voltage regulation, ultra power filtration and conditioning
of normal and common mode noise which accounts for 90% of power-related
problems experienced by copiers, mailing systems, large format printers and
other office equipment.
UNINTERRUPTIBLE POWER SUPPLIES – UPS SERIES
Smart Power Systems’ Uninterruptible Power Supplies (UPS) with integrated TBF™
Technology provide online power conditioning.
WARRANTY
Limited Lifetime Warranty
All Copier Guardian II Filters Series are guaranteed free of defects in
material or workmanship for the life to the original purchaser –or, they will
be repaired or replaced free of charge. See our website for more details –
www.smartpowersystems.com
$25,000 Connected Equipment Warranty
If the Smart Power Systems equipment fails and this failure allows a surge to
pass through and damage the connected equipment, Smart Power Systems will pay
for the repair or replacement of the connected equipment of the original
purchaser . Please take the time to register each Smart Power Systems’ product
along with the connected equipment devices connected to it within 10 days of
date of purchase in order for you to take advantage of this product warranty
and connected equipment protection policy. See our website for more details –
www.smartpowersystems.com
IMPORTANT
If for any reason you need to return the Copier Guardian II unit to the
manufacturer, you should obtain an RMA (Return Material Authorization) number
before returning the unit. To request an RMA number please call
1-800-772-7633 or visit the website at
www.smartpowersystems.com/main/rma.htm
7409 Railhead Ln. – Houston, Texas 77086 – Tel:(713)464-8000 –
Fax:(713)984-0841
E-mail: [email protected]
www.smartpowersystems.com